Dorma TS93 ST User manual

(REFERENCE UNIT CARTON LABEL FOR ACCESSORIES AND OPTIONS SUPPLIED)
M5 HEX KEY
COMPONENTS TO UNREINFORCED DOORS AND TO WOOD
TS93 ST
LEFT HAND DOOR
PULL SIDE TRACK MOUNT
Determine hand of door and degree of deadstop required.
Prepare door and frame for fasteners
1
according to template 08280182.
2
3
4
LEFT HAND DOOR RIGHT HAND DOOR
Attach mounting plate to door, using lower four QTY
(4) WOOD
DOORS
METAL
DOORS
RIGHT HAND DOOR LEFT HAND DOOR
QTY
(4)
Attach closer to mounting plate. QTY
(4)
RIGHT HAND DOOR LEFT HAND DOOR
QTY
(1)
RIGHT HAND DOOR
Attach arm to pinion of closer, parallel to door.
holes in plate. Use upper four holes for optional
mounting. Arrows on plate face top of door.
MANUFACTURER'S LISTINGS.
ALTERNATIVE METHOD IS IDENTIFIED IN THE INDIVIDUAL DOOR
CAUTION: SEX NUTS ARE REQUIRED FOR ATTACHMENT OF
OR PLASTIC FACED COMPOSITE TYPE FIRE DOORS, UNLESS AN
M5 HEX KEY
www.dorma-usa.com 1-800-523-8483
INSPK NO. 08280180 Rev.10/09
08280181 05/09
PAGE
Description:
INS NO. Rev.
1 of 3

screw and tighten securely. Install track cover.
Attach arm to slide shoe.
Align hole in arm with slide shoe in track. Insert
QTY
(1)
M5 HEX KEY
SLIDE
TRACK
END BLOCK
SPRING ON
SHOE
HINGE SIDE
QTY
QTY
(2) WOOD
FRAME
METAL
FRAME
(2) TRACK MOUNTING
BRACKET
ANGLE
08280181 2 of 3 05/09
INS NO. PAGE Rev.
56
7
Assemble track and attach to frame.
Adjust sweep, latch, backcheck and delayed
action valves.
1 - SWEEP speed from
2 - LATCH speed from approx.
70° to 0°
7° to 0°.-(INCREASE ONLY)
DECREASE
INCREASE SWEEP
RANGE
LATCH RANGE
CAUTION: DO NOT REMOVE VALVES.
BACKCHECK RANGE
4 - DELAY speed from max opening 180° to 70°
CAUTION: DO NOT CLOSE VALVE COMPLETELY.
DECREASE
INCREASE
BACKCHECK (INTENSITY)
3 - BACKCHECK cushion effect.
142 3
DELAY
ACTION
RANGE
Attach track assembly to frame.
Attach track to angle bracket using track mounting screws.
Insert slide shoe and end blocks into track with spring block
near the hinge side of door frame.
L HINGES
C

Install cover.
screw.
Secure with locking
TAB
COVER
cover onto plate.
END COVERS
end caps.
Slide end covers over closer body
REMOVE
Remove tab that aligns with arm hub. Slide
9
08280181 3 of 3 05/09
INS NO. PAGE Rev.
8
adjusted to meet barrier-free forces may not have sufficient
Take an opening force reading from
CAUTION: DO NOT OVERTIGHTEN
to meet the barrier-free requirement. Maximum number of
clockwise =12. Depending on opening conditions, a door
turns counter clockwise=5. Maximum number of turns
power to reliably close and latch the door.
ULC LABELED UNITS "ONLY"
NON-BARRIER-FREE OPENINGS:
Adjust according to chart.
Adjust according to chart.
Adjust spring tension, if required.
TS93-1 supplied with a size 2 spring setting.
CRITICAL
the pull on the door. If required, adjust the spring tension
REFERENCE LABEL ON CLOSER FOR MINIMUM/MAXIMUM SETTINGS
BARRIER-FREE OPENINGS -
+
-
+12
200 5
WEIGHT (LBS)
CLOSER
TS93-1
TYPE
100
150
125
DOOR
4'
3'6"
3'
2'6"
3'6"
MAX.
3'
2'6"
---
SPRING
ADJUSTER
OF SPRING
2
4
3
SIZE
0
+9
+3
FULL TURNS
+12
+3
+9
0
5
3
4
2
SPRING ADJUSTER
FULL TURNS OF
INT.
DOOR WIDTH
EXT. CLOSER
SIZE
M5 HEX KEY
NOTE:
TS93-5 supplied with a size 6 spring setting.
NOTE:
Maximum number of turns clockwise = 6
TS93-1
0
SPRING ADJUSTER
FULL TURNS OF
4'
4' 6"
TS93-5 DOOR WIDTH
EXT.
3' 6"
INT.
4' -4 6
CLOSER
SIZE
5
0
-4
5
6
200
250
TS93-5