Electro Industries Mini-Boiler EMB-W-9 Manual

10/22/2008 BI302B
Electric
Mini-BoilerTM
Installation & Operating
Instructions
Model EMB-W-9 9 kW 2 GPM minimum flow
Application - Low temperature, low pressure, radiant underfloor heating systems. This model
includes a factory installed WarmFlo®aquastat.
Comment - If this application is for traditional hydronics heating requiring temperatures greater than
14Øand capacities larger than shown above, contact factory for other Electro-Boiler product series.
If this application requires temperatures greater than 140°, this is the wrong model. Contact the
distributor or factory for the EB-M*-** model series which is designed for temperatures up to 180°.
This series can also do outdoor reset and other features.
Accessories – Attached BL001 lists various accessory or option items which are not part of basic
Electro-Boiler. Page 1 gives information on a zone control update which stages elements based upon
zone capacity.
Note: This product meets the requirements of the ASME Boiler and Pressure
Vessel Code.
Drawings: BX304
BH304
BS304
BS309
BD705
BH007
BL001

10/22/2008 BI302B
TABLE OF CONTENTS
Description Page
System Components 1
SystemorWaterFlow 1
Room Thermostat Placement 1
Built in Temperature Control 2
Water Flow Calculation 2
Installation Requirements 2
Mechanical Installation 3
Electrical Hookup 4
Water Fill Procedure 6
OperationalTips 7
Troubleshooting Helps 8
Drawings:
Piping, install kit BX304
Hook-up BH304
Internal Wiring (reference information) BS304
Schematic, one line BS309
Sensor Installation BD705
Zones BH007
Boiler Accessories BL001

10/22/2008 1BI302B
GENERAL
As stated, this product series applies to underfloor hydronics heating. The basic components for an electric energy heating
system typically includes:
1. Electric Mini-Boiler itself – covered by this manual
2. Thermostat control – covered by this manual
3. Plumbing kit or piping material at the boiler itself - Can be ordered as a kit, reference catalog number EMB-PK.
These items are shown on plumbing installation drawing BX304.
4. Circulating pump - Typically sized for head pressure and system flow requirement, typical catalog number
EMB-P2.
5. The underfloor circulating tubes and manifolds - Provided and manufactured by others, not covered in this
manual.
APPROVED TUBING/PIPING
When plumbing this boiler and its peripheral parts to the loop system, all plumbing parts and/or tubing must be sealed to
prevent entrance of oxygen.
Use only tubing or polyethylene tubing with oxygen Diffusion Barrier (ie. PEX).
WARMFLO AQUASTAT
This model is factory equipped with the WarmFlo®comfort module setup specifically for boiler water temperatures.
During installation the sensor must be installed within the pipe well (see Mechanical section) and the controller modulates
or regulates the elements to maintain a preset maximum or preset operating temperature. The circuit board has a
screwdriver adjustment (see Operational Tips section) for setting the operating temperature point.
During initial turn on (slab stat call for heat) both elements come on full. When the water temperature reaches the set
point, the first 4.5 kW element begins turning off and on in an attempt to regulate at this specific temperature. Assuming
proper flow, the element power will regulate to maintain this preset temperature. If Stage 1 is totally off and the
temperature overshoots by 5°, Stage 2 element is also turned off.
ROOM THERMOSTAT PLACEMENT
Comfort and proper space heating response is a direct relationship to the room thermostat type and the placement of the
thermostat sensing bulb. Typically an underfloor heating system can be broken down into two categories.
Energy storage, water tubing is under the concrete or within the sand base - The controlling thermostat
must have a remote bulb, and this remote bulb must sense the concrete slab temperature (slab stat).
Coordinated with the concrete pour, install a ¾” PVC, minimum bend radius of 7 inches, and locate at
approximately center (vertical) of the concrete slab. The thermostat sensing bulb can later be pushed down
this PVC conduit. If the slab is already poured without conduit for slab stat, use electronic remote sensing
thermostat such as Electro Industries’ ES-24-SRO. This type of device only requires a ¼” hole drilled in the
concrete at some center wall location.
Quick response, hydronics tubing just under the concrete surface, no flooring material over the
concrete - In this case, heated water can directly radiate into the room, a standard wall mount room
thermostat is adequate. Mount room thermostat on an inside wall similar to most heating systems.
Comment: If the slab was poured without the conduit, Electro Industries can provide a remote sensing
slab stat with a remote sensor requiring only a ¼” hole. If it is at an inside wall, the ¼” hole need only be
1’ or 2” away from the plate. If it is an outside wall you should go in about 24”. Simply insert the sensor
about 2” and fill with basic silicone to keep the sensor protected within the hole.

10/22/2008 2BI302B
TEMPERATURE CONTROL
The hi-limits within this unit are for safety purposes only. The system installation must have a proper responding slab
sensing thermostat to properly turn the boiler on and off. If the water flow is greater than the minimum GPM specified,
this boiler should not reach hi-limit and the hydronics loop should continue to flow in the normal heating pattern until the
operating slab stat is satisfied. If hi-limiting is experienced prior to satisfying the operating slab stat, there is probably a
water flow problem.
The WarmFlo®aquastat sensor is designed to control the temperature at the set point; however, depending upon the sensor
location, water flow through the pipe at the sensor well, and the non-failure of the circuit board; the temperature of this unit
should never reach hi-limit (160°). The limits are provided as a safety backup to the WarmFlo®modulator.
INFORMATION/WATER FLOW CALCULATIONS
Water flow, GPM, can easily be calculated if the temperature rise across the electric boiler can be measured.
The formula below can only be used when the temperature rise is stable and the boiler is not hi-limiting. In other words,
verify constant current draw and stable outlet temperatures for at least 15 minutes.
Volts x Amps x 3.4 240 volts x 36 amps x 3.4 29376
GPM= 500 x Temp. rise Example: 500 x 10 degree rise = 5000 = 5.8 gpm
INFORMATION/WATER FLOW CALCULATIONS – METRIC
Volts x Amps x 3.587 240 volts x 36 amps x 3.587 30991.68
L/min = 251.04 x Temp. rise ° C Example: 251.04 x 6° C rise = 1506.24 = 20.57 L/min
INSTALLATION REQUIREMENTS
1. All installation work must be performed by trained, qualified contractors or technicians. Electro Industries, Inc.,
sponsors installation and service schools to assist the installer. Visit our web site at electromn.com for upcoming
service schools.
WARNING
ALL ELECTRICAL WIRING MUST BE IN ACCORDANCE WITH NATIONAL ELECTRIC CODE
AND LOCAL ELECTRIC CODES, ORDINANCES, AND REGULATIONS.
WARNING
OBSERVE ELECTRIC POLARITY AND WIRING COLORS. FAILURE TO OBSERVE COULD
CAUSE ELECTRIC SHOCK AND/OR DAMAGE TO THE EQUIPMENT.
CAUTION
This unit can only be used for its intended design as described in this manual. Any internal
wiring changes, modifications to the circuit board, modifications or bypass of any controls, or
installation practices not according to the details of this manual will void the product warranty,
the CSA/us certification label, and manufacturer product liability. Electro Industries, Inc.,
cannot be held responsible for field modifications, incorrect installations, and conditions which
may bypass or compromise the built-in safety features and controls.
2. This installation manual and Electro-Boiler products relate only to the addition of the Electro-Boiler to the hydronics
system. The owner/installer assumes all responsibility and/or liability associated with any needed installation of the
gas/oil boiler, pump, plumbing, system design, etc. Any instructions or comments made within this manual (or factory
phone assistance) relating to the hydronics system or backup gas/oil boiler are provided as comments of assistance and
“helps” only.

10/22/2008 3BI302B
CAUTION
Hazards or unsafe practices could result in property damage, product damage, severe personal
injury and/or death.
3. Remember, safety is the installer’s responsibility and the installer must know this product well enough to instruct the
end user on its safe use.
Safety is a matter of common sense - - a matter of thinking before acting. Professional installers have training and
experienced practices for handling electrical, sheet metal, and material handling processes. Use them.
CLEARANCES
MINIMUM CLEARANCE FROM
COMBUSTIBLE SURFACES SUGGESTED MINIMUM SERVICE CLEARANCE
BACK 0 INCH 0 MM 0 INCH 0 MM
LEFT 1 INCH 25 MM 6 INCHES 152 MM
RIGHT 1 INCH 25 MM 6 INCHES 152 MM
FRONT 1 INCH 25 MM 24 INCHES 610 MM
TOP 1 INCH 25 MM 24 INCHES 610 MM
BOTTOM REQUIRED CLEARANCE – 10 INCHES/254 MM
AVAILABLE, ELECTRO INDUSTRIES, INSTALL PARTS OR KITS
EMB-BK MINI-BOILER PLUMBING KIT BASIC
EMB-P2 PUMP KIT 1/25HP BOILER
ES-24-SRO STAT DIG SLAB/ROOM/ROOM 24VAC
@WFS5 WATER SENSOR
5616 TRANSFORMER HTR 4X4 PLATE 40VA 24VAC
5576 AIR ELIMINATOR 3/4" ROLLAIRTROL
5456A GAUGE PRES/TEMP 75 PSI/320DG F .25"
5453 VALVE RELIEF 30 PSIG .75” NPT MALE
5590 EXPANSION TAN K 40K BTU 20.1 GALLON
EMB-PK MINI-BOILER INSTALL KIT PREFERRED
EB-5415A ZONE CONTROLLER
MECHANICAL INSTALLATION
CAUTION
Electro Industries Inc. requires the use of dielectric isolation between the boiler vessel supply and return
piping when the boiler is plumbed using copper or any other dissimilar metal. Damage to the vessel
caused by galvanic corrosion voids Electro Industries’ warranty.
Reference drawing BX304
At the outlet pipe the first fitting must be the supplied Tee with the sensor well fitting. It is important that the WarmFlo®
aquastat sensor be as close as possible to the vessel, reference detail A on drawing BH304. Please reference BD705 for
proper installation of the sensor. After the Tee and the sensor have been permanently installed, route the sensor cable
along the right side of the unit and properly affix (do not puncture cable) to the wall.
The plumbing components and piping layout shown on drawing BX304 has been very carefully picked and should be
plumbed as shown. When following this diagram, the water fill procedure becomes very simple and almost guarantees the
removal of all air or prevents air locking problems. Experienced hydronic heating installers may be able to eliminate
components such as regulated fill valve, check valve, temperature gauge, etc., but the inclusion of these components
guarantees installation and initial operating success.
The key mechanical components required include:

10/22/2008 4BI302B
Boiler/Plumbing Kit Placement – This model series is wall hung and the vessel must be vertical.
The plumbing kit items are located adjacent to the boiler housing itself as shown on drawing BX304.
For future servicing, the unit itself must be installed a minimum of 18” above the floor. The
elements are screwed in from the bottom.
Allow adequate space for cover removal and maintenance.
Expansion Tank - As a closed loop hydronic heating system, a minimal expansion tank is required. This can
be an air diaphragm tank as provided in the plumbing kit or a basic “empty” tank where air is compressed at
the tank top.
Temperature/Pressure Gauge - Recommended to observe the operation of the system. Actually a
temperature gauge at the inlet and outlet is desirable.
Pressure Safety Valve - This is required at the hot outlet and is furnished as a loose component with the
boiler unit itself. Failure to install the provided, 30 PSI, pressure relief valve as shown void warranty and the
CSA product listing.
Add the necessary pipe extension from the relief valve to the floor to prevent water damage on this unit or
surrounding area.
Gate Valve/Drain Valve - These are for servicing and easy fill purposes.
Circulating Pump - Depending upon system lift and system loop resistance (feet of head), the proper
circulating pump is required to guarantee the minimum GPM flow as specified on the cover sheet.
Comment: Circulator pump can be in the outlet or inlet. However, the circulator pump should “pump away
from” the expansion tank.
Air Vent – Whenever there is a plumbing point higher than any of the components shown or an adjacent line
(any vertical “U” trap), an air vent valve should be provided.
Building Water Supply Connection – Reference drawing BX304, note 4, some local building codes require
sophisticated check valve or anti-siphon check valve when the hydronics heating system is permanently
connected to the domestic water system. The intent of this connection is temporary and for fill purposes only.
The installer has the responsibility of complying with local building codes.
ELECTRICAL HOOKUP
Reference drawing BH304.
WARNING
DISCONNECT ALL ELECTRICAL POWER BEFORE ELECTRICALLY CONNECTING OR
SERVICING THE UNIT. FAILURE TO DISCONNECT THE ELECTRICAL POWER BEFORE
WORKING ON THIS PRODUCT CAN CREATE A HAZARD LEADING TO PERSONAL INJURY
OR DEATH.
1. Panel breaker sizes – 4.5 kW Mini-Boiler will require 30-amp breaker, copper wire. 9 kW Mini-Boiler will
require 50-amp breaker, copper wire.
2. 24Ø Volt Power Source – route and install the proper current carrying conductors, suggested by local codes,
from service panel fuse or circuit breaker. Nameplate shows current & KW rating.
NOTE: This model series is designed and equipped for 240-volt residential single phase. If this unit is used on 208
volt, energy capacity is reduced and there is a possibility of intermittent relay operation. Call factory for 208-volt
application.
The source is either from the standard service panel or may be part of an off-peak separately metered panel/CT
metered enclosure. Consult with local utility if questions on off-peak installations.
Since this unit is less than 10 kW, no fusing or circuit breaker at the boiler itself is required. The 240-volt (L1,
L2, with copper ground) is connected directly to the left bottom terminal block.

10/22/2008 5BI302B
WARNING
USE ONLY COPPER WIRE FOR CONNECTION TO THE CIRCUIT BREAKER TERMINALS
AND INSIDE THIS PRODUCT’S CABINET.
WARNING
TO AVOID THE RISK OF ELECTRIC SHOCK OR DEATH, WIRING TO THE UNIT MUST BE
PROPERLY GROUNDED. FAILURE TO PROPERLY GROUND THE UNIT CAN RESULT IN A
HAZARD LEADING TO PERSONAL INJURY OR DEATH.
3. Circulating Pump – the two screw terminals (orange wires) represent a switch closure (see drawing – 10-amp
maximum) to operate the circulating pump motor. Voltage for the pump must come from a separate source.
Wiring entrance must be left KO, do not combine with thermostat cable or other control wiring.
4. Operating Thermostat – zone valve dry contact end switch is an operating contact, direct wired thermostats
include:
Standard Mechanical – connect to control board “R” and “W”. Important! -Set thermostat internal heat
anticipator to Ø.2.
Electro-Stat - (ES-24-SRO) 4 wire connection required. This is an electronic remote sensing device, remote
sensor can be up to 50 feet, cut and splice as required. Use only stranded wire, shielded cable not required.
The primary advantages include the capability for longer sensor and the sensor itself is less than ¼”. This
means it can be installed after the slab is complete by simply drilling a ¼” hole, 1/8” slot, etc. slightly out
from an inside wall.
* R to R, W to W, C to C, green to ground
* Use drawing EH304 (with ES product) for hookup, note change in load control connection.
WARNING
VOLTAGE SEPARATION IS REQUIRED. THE 24Ø POWER AND PUMP WIRING MUST
REMAIN LEFT OF THE BOTTOM PIPE. THE THERMOSTAT WIRES AND LOAD CONTROL
WIRING (BLUE & BLUE/WHT) MUST EXIT AND REMAIN ON THE RIGHT SIDE OF THE
BOTTOM PIPE.
5. Load Management Interrupt Control – this Mini-Boiler product has been pre-wired and designed for a power
company load management receiver connection. This should not be altered in any manner!
A. Remove blue jumper wire
B. Extend or connect the two terminal screw points to the power company load control device.
As shipped, this unit is only equipped for off-peak =N.C. logic. If reversed logic is required, contact the
factory for modification.
Optional – if load management is not used, simply leave the blue wire jumper connected as shipped from
manufacturer. Also for Electro-Stat the load control connection is at the Electro-Stat “R” terminal.
6. Zone Valve – do not power from EMB internal transformer. Contractor needs to install separate 24VAC
transformer to operate zone valves. Suggest adding zone interlock control, EB-5415A . Call factory.
7. Inspection/final check – Verify all electrical connections are tight (including factory connections), verify there is
proper spacing between all power and electrical wire/terminals, and verify top high limit manual reset is “in”.
During shipping freight vibration there are times when the boiler vessel top manual reset high limit is “popped
out”.
WATER ADDITIVES
1. Unless the source water is unusually poor and/or rust elements, additives are not required. It is recommended the
water source as shown on drawing BX304 comes through the household water softener.

10/22/2008 6BI302B
2. Impurities within a closed loop hydronics boiler are considerably less damaging than the typical domestic water heater.
In a closed loop electric boiler, the water impurities “boil out” and the system essentially reverts to pure water. As a
closed system, this “pure water” becomes the operating mode. In the case of domestic water tank, there is always new
water entering with new impurities.
3. However, if additives are required, use the recommendations and source from your local professional plumber,
specializing in hydronics heating systems.
WATER FILL PROCEDURE
The following procedure only applies to the prepackaged plumbing kit and/or when the system is plumbed exactly as
shown on drawing BX304.
1. Connect the temporary household water supply source (probably hose connection) to the "supply water connection"
input.
NOTE: If supply water connection is permanent, some local building codes may require special anti-siphon
check valve, PRZ check valve, or equivalent between the Mini Boiler fill regulator and the domestic water source
or the city water connection.
2. Connect a drain hose to lower hose bib, "drain valve".
3. Open "drain valve" and close "inlet gate valve" (between drain valve and boiler bottom inlet).
4. Verify “top gate valve” is open.
5. Do not apply 24Ø volt heating power during water fill sequence.
6. Open "water supply valve" and open household water supply source.
This may be at normal household pressure (4Ø to 6Ø PSI), the auto-fill value regulator keeps the
hydronics loop at its proper low pressure.
7. Allow system to circulate, discharging through drain valve, for at least 1Ø minutes.
8. Put your ear against the metal pipe and listen for air bubbles. If the water flow is consistent and quiet, the system is
probably purged and water filled.
9. Close the "drain valve". Open the "inlet gate valve".
10. The cold system pressure at the gauge should be approximately 1Ø to 14 PSI.
11. Close "water supply valve" and disconnect water supply.
12. Optional – The circulating pump can be energized during this fill operation by having the 240 power main source
breaker off and simply jumpering the 2 screw terminals for the pump wire connection.

10/22/2008 7BI302B
Figure 1
OPERATIONAL TIPS
1. Indicator lights – there is a set of four indicator lights on the lower right corner of the front cover with an identical set
of four indicator lights on the internal circuit board itself. Figure 1 is a reproduction of the front decal giving
definition and information for using these indicator lights. Note the statement that there must be a call for heat before
attempting to interpret the indicator lights.
2. 24Ø volt element power current flow can be measured when the external operating thermostat is calling for heat.
There are no delays.
Assumes off-peak mode.
3. The operating thermostat heat call can be verified by the red LED marked “Mini-Boiler heat on” located on front
cover.
4. The 160° (71° C) hi-limit is automatic reset.
5. The 205° (96° C) hi-limit is manual reset and under the cover, located on the vessel
top, left.
Warning: This 205° (96° C) manual reset controls the 240 power to the elements.
Therefore, open the boiler disconnect prior to removing cover and prior to
attempting to reset this limit. Note: Reset tab is brass in color and located on the
side of the hi-limit.
6. Via a small pin jumper arrangement on the control board, the circulator pump can be a
direct function of the “W” input or interrupted by the load control device (even though
there is a W input). This diagram illustrates this pin jumper arrangement. This unit is
factory setup in the “W” position meaning the pump will always run as a direct
function of “R” to “W” operating thermostat. By simply moving this black 2-position
jumper to the “L” the pump will be turned off during load control interrupt.
7. At outlet temperatures of approximately 120F (53° C), the maximum system pressure should be approximately 18
PSI (124 kPa). If the PSI (or kPa) increase from cold water to operating hot water is more than approximately 3 to 4
PSI (20.6 to 27.5 kPa), the expansion tank is too small.
8. Check for water leaks and repair as required.
9. If flow seems to be a concern, determine both inlet and outlet water temperature and apply GPM (L/min) formula
detailed in previous section “Information/Water Flow Calculations”.

10/22/2008 8BI302B
WARMFLO AQUASTAT OPERATION
Sensor cable installation – see previous paragraph, Mechanical.
Determine from floor tubing supplier design outline the desired floor temperature. Typically this relates to floor covering
and tube placement design. Set the aquastat set point for desired warm water outlet.
The temperature set point is selected by a small screwdriver switch on the control board. Use the following chart:
Switch Position Set Point
0 85
1 95
2 105
3 115
4 125
5 135
6 145
7 150
The green LED on the circuit board is on whenever Stage 1 electric element is on. This can either be full on, pulsing at a
slow rate, or full off.
TROUBLESHOOTING HELPS
Monitor – the green LED to the left of the dial switch not only indicates the first element operating on/off, but also
provides some sensor quality information. If this LED is pulsing, there is either a shorted sensor, open wire to the sensor,
or some sensor wiring error. The internal logic is not receiving temperature information from the sensor tip.
The default for a bad sensor – boiler operates at half capacity, stage 1 on, stage 2 off.
Sequence
At heat call, elements 1 and 2 are full on.
As the outlet temperature approaches the set point, element 1 begins to pulse modulate.
At set point element 1 is off or 0%.
At +5° above set point element 2 turns off.
At set point element 1 again begins to modulate.
At 5° below set point element 1 is at 100% and element 2 would again turn on.
Mechanical hi-limit, top vessel screw-in, automatic reset – this is at about 160° F, opens the red/white wire loop. This
can be monitored by the “Auto Reset” front indicator light. As the water cools to approximately 120° it should self reset
and restart.
Manual reset limits – surfaced mounted to the top of the vessel, opens at 205° F. This actually opens the current carrying
leg to each element and prevents 240 power from reaching the element. This can be monitored from the “Manual Reset”
front indicator light.
To reset this device, notice a small shiny lever protruding from one side of the black insulator. Simply push this lever
inward and it should snap.
Comment: These lights will only be active during a heat call and when the element relay is closed.
WARMFLO TEMPERATURE BYPASS TROUBLESHOOTING OR TESTING
Adding a jumper between “W” screw terminal and tab marked “E” bypasses the temperature sensing and WarmFlo control.
In other words, with the jumper installed a “W” input represents 9 kW, full on.

E L E C T R O I N D U S T R I E S , I N C .
M ON T I C E LL O , M N 55362
M I N I - B O I L E R H OO K U P ( E M B - W - 9 )
B H 304 P . 1
R e v . G 03 - 06 - 07
A
A
W A T E R
S E N S O R
R
E F E R E N C E BD 705 F O R
PR
O P E R S E N S O R I N S T A LL A T I ON
3 / 4 " - 1 / 4 " B U S H I N G
( X B S H 7125 )
1 / 4 " X 3 / 4 " P I P E W E LL
( # 5533 )
3 / 4 " T EE
( X T EE 7000 )
M I N I - B O I L E R
OU T L E T P I P E
1 / L 1 2 / T 1
4
/ A 2 3 / A 1
F U S E
2 A M A X .
I N D I C A T O R L I G H T S
U T I L I T Y O FF - P E A K ( A M B E R )
205 ° F ( 96 ° C ) M A NU A L R E S E T L I M I T ( R E D )
160 ° F ( 71 ° C ) A U T O R E S E T L I M I T ( R E D )
M I N I - B O I L E R H E A T ON ( R E D )
NO T E S :
1 . T H I S UN I T H A S A FA C T O R Y - I N S T A LL E D B L U E J U M P E R T H A T B Y P A SS E S
T H E L M C M O D E . W H E N L M C O P T I ON I S U S E D , R E M O V E J U M P E R B E F O R E
I N S T A LL I N G .
2 . L I G H T S O P E R A T E ON L Y ON T H E R M O S T A T C A LL F O R H E A T .
3 . J 4 M U S T H AV E E X T E R N A L L E D P L U GG E D I N O R J U M P E R E D F O R
ON - B O A RD L E D T O O P E R A T E .
4 . A N Y 2 - W I R E S T A T O R E N D S W I T C H C ON T A C T C A N B E U S E D T O O P E R A T E
R & W , E L E C T R O - S T A T S HO W N A S E X A M P L E ON L Y .
5 .
6 . T R A N S F O R M E R F O R I N T E R N A L C I RC U I T S ON L Y . Z ON E VA L V E S , E T C . M U S T
H AV E T H E I R O W N 24 V S OU RC E .
7 . H I G H V O L T A G E & L O W V O L T A G E W I R I N G M U S T H AV E M I N I M U M 1 " ( 2 . 5 C M )
S P A C I N G .
N E U T R A L
120 VA C
C
I RC U I T BR E A K E R
S OU RC E P O W E R
C
I RC U I T BR E A K E R
A
R
L
L 2
L 1
P U M P
( T B 2 " C ")
(
T B 2 " R ")
( T B 2 " W ")
(
T B 1 )
( T B 1 )
S HO W N W I T H
C O V E R R E M O V E D
NO I N T E R N A L
W I R I N G S HO W N
C O PPE R O N L Y
L1
SEE N A M EP L A T E F O R
CURR E N T R A T I N G .
U A S 300
C I RCU L A T I N G P U M P
S W I T CH C L O S UR E -
P O W E R C I RCU I T I S EX T E RN A L .
C O N T A C T R A T I N G -
10 A A T 120 V O L T S .
L2
G
G L 1 L 2
1
T - S T A T
C A B L E
3
2
2
L M C
B L U E
B L U E
4
W 4
E
T 9
T 3
T 4
G
T 2
B L U/ W H T
B L U E R
T B 1
S E T T E M P .
S W 1
T B 2
T E M P . S E N S O R
U PCB 562 1
R E D
C
O M
B L K
T 8
T 7
C S
C
O
M
NO
T
B
3
L E D 4
W 5
K 1
W 1
W C
L E D 2
L E D 1
ON
H
E A T
M O D E
E
L
1
J
2
J 3
1
N 1
L E D 3
L
H L
1 60
o
J1
H L
205
o
W
J 4
1
1
T 1 0
T 11
1 60
T 2
T 1
W 2
205
W 3
T R 1
NO
C
O
M
T 6
K 2
240 V A C
T 5
T E M P . S E N S O R
D E T A I L A - A
S C A L E 3 : 1
R E D
C
O M
B L K
T
B
3
E L E C T R O - S T A T
( E S - 24 - BR )
S L A B S E N S O R

E L E C T R O I N D U S T R I E S , I N C .
M ON T I C E LL O , M N 55362
B H 304 P . 2
R e v . G 03 - 06 - 07
M U L T I - Z O N E , A N Y NU M BE R O R S I Z E .
M I N I - B O I L E R H OO K U P ( E M B - W - 9 )
( T B 1 )
(
T B 1 )
B L U E
B L U E
L M C
( T B 2 " W ")
(
T B 2 " R ")
Z ON E 1
VA L V E S
Z
ON E
# 1 # 2
T h e r m o s t a t s
R oo m
C
R
W
C
1
M
W
24 V
C
120 V
C
W
1
M
Z ON E 2
R
C W
R
T Y P I C A L Z ON E VA L V E
- 2 - W I R E S T A T
- I S O L A T E D E N D S W I T C H
- E X A M P L E : HON E Y W E LL
V 8043 F S E R I E S O R
E QU I VA L E N T
4 - W I R E
T H E R M O S T A T
C A B L E
4 - W I R E
T H E R M O S T A T
C A B L E
R
E
D
R
E
D
R
E
D
R
E
D
Y E L
Y E L
Y E L
Y E L
GR
EE
N
GR
EE
N
P I P I N G M A N I F O L D
NO T E S :
1 . Z ON E VA L V E E N D S W I T C H E S , M U S T B E I S O L A T E D C ON T A C T .
2 . U S E T R A N S F O R M E R O P E R A T I N G Z ON E VA L V E S Y S T E M . D O
NO T U S E B O I L E R T R A N S F O R M E R F O R Z ON E VA L V E S .
3 . S A M E HOO K - U P F O R A N Y NU M B E R O F Z ON E S .
W
W
R
R
P O W E R F R O M
P U M P CB
S EE
P A G E 1
C I RC U I T BR E A K E R
120 VA C
N E U T R A L
P U M P
T - S T A T
C A B L E
S OU RC E P O W E R
C
I RC U I T BR E A K E R
W 4
E
T 9
T 3
T 4
G
T 2
B L U/ W H T
B L U E R
T B 1
S E T T E M P .
S W 1
T B 2
T E M P . S E N S O R
U PCB 562 1
R E D
C
O M
B L K
T 8
T 7
C S
C
O
M
NO
T
B
3
L E D 4
W 5
K 1
W 1
W C
L E D 2
L E D 1
ON
H
E A T
M O D E
E
L
1
J
2
J 3
1
N 1
L E D 3
L
H L
1 60
o
J1
H L
205
o
W
J 4
1
1
T 1 0
T 11
1 60
T 2
T 1
W 2
205
W 3
T R 1
NO
C
O
M
T 6
K 2240
V A C
T 5
1 / L 1 2 / T 1
4
/ A 2 3 / A 1
G
C O PPE R O N L Y
L1
SEE N A M EP L A T E F O R
CURR E N T R A T I N G .
U A S 300
C I RCU L A T I N G P U M P
S W I T CH C L O S UR E -
P O W E R C I RCU I T I S EX T E RN A L .
C O N T A C T R A T I N G -
10 A A T 120 V O L T S .
L2
G
L 2 L 1
L 1
L 2
A
R
L
S HO W N W I T H
C O V E R R E M O V E D
NO I N T E R N A L
W I R I N G S HO W N
M I N I - B O I L E R H E A T ON ( R E D )
160 ° F ( 71 ° C ) A U T O R E S E T L I M I T ( R E D )
205 ° F ( 96 ° C ) M A NU A L R E S E T L I M I T ( R E D )
U T I L I T Y O FF - P E A K ( A M B E R )
I N D I C A T O R L I G H T S
F U S E
2 A M A X .
3
# 5616
T R A N S F O R M E R
# 5544 # 5544
E L E C T R O - S T A T
( E S - 24 - BR )
S L A B S E N S O R
E L E C T R O - S T A T
( E S - 24 - BR )
S L A B S E N S O R

09/26/2001 1 BD705
ELECTRO-BOILERSENSOR INSTALLATION
Once the pipe well has been installed. Liberally apply the supplied heat compound
around the tip of the Warmflo sensor.
Then gently insert sensor into pipe well. Note: Using the tip of your finger, or another
non-piercing object will aid in the insertion of the rubber grommet.
Once the grommet has been inserted into the well gently press the sensor until it reaches
the bottom of the pipe well.
Installation complete.

E L E C T R O I N D U S T R I E S , I N C .
M ON T I C E LL O , M N 55362
W A R M F L O B O I L E R Z O N E V A L VE H OO K U P
B H 007 P . 1
R e v . C 03 - 06 - 07
NO T E S :
1 . Z ON E VA L V E E N D S W I T C H E S , M U S T B E I S O L A T E D C ON T A C T .
2 . U S E T R A N S F O R M E R O P E R A T I N G Z ON E VA L V E S Y S T E M . D O
NO T U S E B O I L E R T R A N S F O R M E R F O R Z ON E VA L V E S .
3 . Z ON E C ON T R O LL E R C A N B E U S E D T O S I M P L I FY HOO K U P .
S EE DR A W I N G B H 009 F O R D E T A I L S .
E L E C T R O - S T A T
Z ON E 1
S
L A B S T A T
P I P I N G M A N I F O L D
VA L V E S
Z
ON E
# 1 # 2 # 3
T h e r m o s t a t s
R oo m
C
R
W
C
1
M
W
24 V
C
120 V
C
W
1
M
Z ON E 2
S
L A B S T A T
R
C W
M
1
C
W
R
C W
Z ON E 3
S
L A B S T A T
T
R A N S F O R M E R
R
R
W
E L E C T R O - B O I L E R
W A R M F L O S E R I E S
E B - W - **
E M B - W - 9
T O A DD I T I ON A L
S L A B S T A T S
( Z ON E S )
T O A DD I T I ON A L
Z ON E VA L V E S
T Y P I C A L Z ON E VA L V E
- 2 - W I R E S T A T
- I S O L A T E D E N D S W I T C H
- E X A M P L E : HON E Y W E LL
V 8043 F S E R I E S O R
E QU I VA L E N T
4 - W I R E
T H E R M O S T A T
C A B L E
4 - W I R E
T H E R M O S T A T
C A B L E
4 - W I R E
T H E R M O S T A T
C A B L E
R
E
D
R
E
D
R
E
D
R
E
D
R
E
D
R
E
D
Y E L
Y E L
Y E L
Y E L
Y E L
Y E L
GR
EE
N
GR
EE
N
GR
EE
N
333
S L A B S E N S O R S L A B S E N S O R
E L E C T R O - S T A T
S L A B S E N S O R
E L E C T R O - S T A T

E L E C T R O I N D U S T R I E S , I N C .
M ON T I C E LL O , M N 55362
W A R M F L O B O I L E R Z O N E V A L VE H OO K U P
B H 007 P . 2
R e v . C 03 - 06 - 07
Z ON E 1
S
L A B S T A T
E I P /N # 7101
Z ON E 2
S
L A B S T A T
E I P /N # 7101
I N - S L A B
S E N S O R
W / 10 F T .
C A B L E
Z ON E 3
S
L A B S T A T
E I P /N # 7101
R
T O A DD I T I ON A L
S L A B S T A T S
( Z ON E S )
T Y P I C A L Z ON E VA L V E
- 2 - W I R E S T A T
- I S O L A T E D E N D S W I T C H
- E X A M P L E : HON E Y W E LL
V 8043 F S E R I E S O R
E QU I VA L E N T
E L E C T R O - B O I L E R
W A R M F L O S E R I E S
E B - W - **
E M B - W - 9
120
V
W
R
C
24 V
C
1
M
1
M
NO T E S :
1 . Z ON E VA L V E E N D S W I T C H E S , M U S T B E I S O L A T E D C ON T A C T .
2 . U S E T R A N S F O R M E R O P E R A T I N G Z ON E VA L V E S Y S T E M . D O
NO T U S E B O I L E R T R A N S F O R M E R F O R Z ON E VA L V E S .
3 . Z ON E C ON T R O LL E R C A N B E U S E D T O S I M P L I FY HOO K U P .
S EE DR A W I N G B H 009 F O R D E T A I L S .
R oo m
T h e r m o s t a t s
P I P I N G M A N I F O L D
VA L V E S
Z
ON E
# 1 # 2 # 3
C
1
M
C
T O A DD I T I ON A L
Z ON E VA L V E S
T R A N S F O R M E R
R
2 - W I R E
T H E R M O S T A T
C A B L E
2 - W I R E
T H E R M O S T A T
C A B L E
R
I N - S L A B
S E N S O R
W / 10 F T .
C A B L E
2 - W I R E
T H E R M O S T A T
C A B L E
R
I N - S L A B
S E N S O R
W / 10 F T .
C A B L E
R
E
D
R
E
D
R
E
D
R
E
D
R
E
D
R
E
D
Y E L
Y E L
Y E L
Y E L
Y E L
Y E L
333

BOILER ACCESSORIES
BOILER ACCESSORIES
This will simplify your wiring and make zoning applications much easier. In addition, enhanced communicating
features have the ability to stage the electric boiler based upon the connected zone capacity.
Standard Features
• Utility load control
• Terminal block wiring, visual
wiring layout
• Indicator lights showing zone
operation
• 24-volt, 40VA transformer
120/208/240 connection
• Fuse protection
• Priority option
• Dual temperature operation
• Applies to digital or
standard thermostats
• Dial switch, select each zone
capacity
Pumps, Actuators, Valves
EB-ZTA-1 - install within boiler cabinet
EB-ZEA-1 - with enclosure and 40VA transformer
EB-ZEA-2 - add additional 4, enclosure and 40VA
Pumps
EB-Z2P - two pumps with priority and dual temp.
Zone Valves
EB-ZTS-1 - install within boiler cabinet, encl. option
EB-ZTS-2 - add additional 4, enclosure and 40VA
All Others
EB-ZXA-1 - universal, pumps or valves, non-communicating, for any boiler
EB-ZS-4 - automatic staging system for Brand X boilers or dual EB-R, -L, -E Series
EB-ZC-4 - wiring and convenience interface, isolated boiler end switch
EB-5415A - low cost, 2 or 3 zones, sheds one boiler stage (Mini-Boiler enhancement)
ZONE CONTROLLER
SLAB STAT
Sensing and controlling the system based upon radiant floor surface temperature
or the concrete mass has very positive benefits. Radiant floor air stat in the same
area as a forced air roomstat presents serious control problems. A remote sensing
slab stat for the radiant floor removes this issue.
Remote sensing slab stat is required for storage applications.
ES-24-BR
SWITCHING RELAY - EE-5051 MULTI-BOILER - EB-C-STG5
This DPDT 24-volt switching relay provides a convenient
solution to any AC or DC application.
• Ideal for zone pumps
• 24V coil
• 120V, 10A, contact sets
• Easy to wire and nicely packaged
Electrically connects between 2nd and 3rd, 3rd and 4th, etc.
OTHER OPTIONS
SOT-1 Switchover to standby, total run time
5701 Single feed bus for 2 CB’s (SQ-D CB)
5702 Single feed bus for 3 CB’s (SQ-D CB)
EB-S-SB Dual boiler option for EB-S Series
WF-ANZ* WarmFlo Analyzer, now applicable to WO and
WA Series
Specifications subject to change without notice, all rights reserved.