Eltron LAB+ Series User manual

User’s Manual No. 980090-001 Rev. B
©1996 Eltron International Inc.
LAB+ Series
User’s Manual
User’s Manual No. 980090-001 Rev. B
©1996 Eltron International Inc.
LAB+ Series
User’s Manual

FOREWORD
This manual provides installation and operation information for LAB+ Series printers
manufactured by Eltron International Incorporated, Simi Valley, California. The contents
includes installation & operation instructions.
TECHNICAL SUPPORT
If for any reason you require product technical support, please contact the Distributor where
you first purchased your equipment. If they cannot help you or at their direction, Eltron
Technical Support can be reached at:
Eltron International Incorporated Eltron International, Europe
41 Moreland Road Unit 2, Rose Kiln Lane
Simi Valley, CA. 93065 Reading, Berkshire, RG2 OHP England
[phone] [phone]
FAX [phone] FAX: [phone]
e-mail: [e-mail]
BBS: [phone]
Return Materials Authorization
Before returning any equipment to Eltron for in warranty or out of warranty repair, contact
Repair Administration for a Return Materials Authorization (RMA) number. Repack the
equipment in the original packing material and mark the RMA number clearly on the outside.
Ship the equipment, freight prepaid, to the address listed below.
Eltron Repair Administration
41 Moreland Road
Simi Valley, CA 93065-1692
[phone]
FAX [phone]
COPYRIGHT NOTICE
This document contains information proprietary to Eltron International Incorporated. This
document and the information contained within is copyright by Eltron International Incorpo-
rated and may not be duplicated in full or in part by any person without prior written approval
of Eltron. While every effort has been made to keep the information contained within current
and accurate as of the date of publication, no guarantee is given or implied that the document
is error-free or that it is accurate with regard to any specification. Eltron reserves the right to
make changes, for the purpose of product improvement, at any time.
TRADEMARKS
LAB+Series is service mark and Eltron is a trademark of Eltron International Incorporated.
Windows & MS-DOS are registered trademarks of Microsoft Corp. All other marks are
trademarks or registered trademarks of their respective holders.
980090-001 Rev.B iii
FOREWORD
This manual provides installation and operation information for LAB+ Series printers
manufactured by Eltron International Incorporated, Simi Valley, California. The contents
includes installation & operation instructions.
TECHNICAL SUPPORT
If for any reason you require product technical support, please contact the Distributor where
you first purchased your equipment. If they cannot help you or at their direction, Eltron
Technical Support can be reached at:
Eltron International Incorporated Eltron International, Europe
41 Moreland Road Unit 2, Rose Kiln Lane
Simi Valley, CA. 93065 Reading, Berkshire, RG2 OHP England
[phone] [phone]
FAX [phone] FAX: [phone]
e-mail: [e-mail]
BBS: [phone]
Return Materials Authorization
Before returning any equipment to Eltron for in warranty or out of warranty repair, contact
Repair Administration for a Return Materials Authorization (RMA) number. Repack the
equipment in the original packing material and mark the RMA number clearly on the outside.
Ship the equipment, freight prepaid, to the address listed below.
Eltron Repair Administration
41 Moreland Road
Simi Valley, CA 93065-1692
[phone]
FAX [phone]
COPYRIGHT NOTICE
This document contains information proprietary to Eltron International Incorporated. This
document and the information contained within is copyright by Eltron International Incorpo-
rated and may not be duplicated in full or in part by any person without prior written approval
of Eltron. While every effort has been made to keep the information contained within current
and accurate as of the date of publication, no guarantee is given or implied that the document
is error-free or that it is accurate with regard to any specification. Eltron reserves the right to
make changes, for the purpose of product improvement, at any time.
TRADEMARKS
LAB+Series is service mark and Eltron is a trademark of Eltron International Incorporated.
Windows & MS-DOS are registered trademarks of Microsoft Corp. All other marks are
trademarks or registered trademarks of their respective holders.
980090-001 Rev.B iii

WARRANTY INFORMATION
We Need To Hear From You!
To establish your warranty period and provide access to Technical Support,
Send Us Your Product Registration Card Today!
Eltron warrants the mechanism, control electronics and power supply, under normal use and
service, to be free from defects in material and workmanship for a period of twelve months
from the date of purchase by the end user. Eltron warrants the printhead, under normal use
and service, to be free from defects in material and workmanship for a period of 90 days from
the date of purchase by the end user. Proof of purchase or product registration is required.
If proof of purchase or product registration cannot beestablished, shipment date to the original
buyer (dealer or distributor) will be be used to establish warranty period.
Failure to exercise caution to protect the equipment from electrostatic discharge damage,
adverse temperatureand humidity conditions or physical abuse may void the warranty. Eltron
will, at it’s option, repair or replace the equipment or any parts which are determined to be
defective within this warranty period and which are returned to Eltron F.O.B. factory of origin.
The warranty set forth above is exclusive and no other warranty, whether written or oral, is
expressed or implied. Eltron specifically disclaims the implied warranties of merchant-ability
and fitness for a particular purpose.
FCC Notice:
This equipment has been tested and found to comply with the limits of a Class A digital device, pursuant to Part 15 of the
FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is
operated in a commercial environment.. This equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular installation. Operation of this equipment in a residential
area is likely to cause harmful interference in which case the user will be required to correct the interference in which case
the user will be required to correct the interference at his own expense.
CSA Notice:
This equipment does not exceed Class A limits per radio noiseemissions for digital apparatus set out in the Radio Interference
Regulation of the Canadian Department of Communications. Operation in a residential area may cause unacceptable
interference to radio and TV reception requiring the owner or operator to take whatever steps are necessary to correct the
interference.
Cet equipment ne depasse pas les limites de Classe A d’emission de bruits radioelectriques pour les appareils numerriques
tells que perscrites par le Reglement sur le brouillage redioelectrique etabli par le ministere des Communications du Canada.
L’exploitation faite en milieu residentiel peut entrainer le brouillage des receptions radio et tele, ce qui obligerait le proprietaire
ou l’operateur a pendre les dispositions necessaires pour en eliminer les causes.
iv 980090-001 Rev.B
WARRANTY INFORMATION
We Need To Hear From You!
To establish your warranty period and provide access to Technical Support,
Send Us Your Product Registration Card Today!
Eltron warrants the mechanism, control electronics and power supply, under normal use and
service, to be free from defects in material and workmanship for a period of twelve months
from the date of purchase by the end user. Eltron warrants the printhead, under normal use
and service, to be free from defects in material and workmanship for a period of 90 days from
the date of purchase by the end user. Proof of purchase or product registration is required.
If proof of purchase or product registration cannot beestablished, shipment date to the original
buyer (dealer or distributor) will be be used to establish warranty period.
Failure to exercise caution to protect the equipment from electrostatic discharge damage,
adverse temperatureand humidity conditions or physical abuse may void the warranty. Eltron
will, at it’s option, repair or replace the equipment or any parts which are determined to be
defective within this warranty period and which are returned to Eltron F.O.B. factory of origin.
The warranty set forth above is exclusive and no other warranty, whether written or oral, is
expressed or implied. Eltron specifically disclaims the implied warranties of merchant-ability
and fitness for a particular purpose.
FCC Notice:
This equipment has been tested and found to comply with the limits of a Class A digital device, pursuant to Part 15 of the
FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is
operated in a commercial environment.. This equipment generates, uses and can radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular installation. Operation of this equipment in a residential
area is likely to cause harmful interference in which case the user will be required to correct the interference in which case
the user will be required to correct the interference at his own expense.
CSA Notice:
This equipment does not exceed Class A limits per radio noiseemissions for digital apparatus set out in the Radio Interference
Regulation of the Canadian Department of Communications. Operation in a residential area may cause unacceptable
interference to radio and TV reception requiring the owner or operator to take whatever steps are necessary to correct the
interference.
Cet equipment ne depasse pas les limites de Classe A d’emission de bruits radioelectriques pour les appareils numerriques
tells que perscrites par le Reglement sur le brouillage redioelectrique etabli par le ministere des Communications du Canada.
L’exploitation faite en milieu residentiel peut entrainer le brouillage des receptions radio et tele, ce qui obligerait le proprietaire
ou l’operateur a pendre les dispositions necessaires pour en eliminer les causes.
iv 980090-001 Rev.B

Table Of Contents
Getting Started
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Unpacking the Printer . . . . . . . . . . . . . . . . . . . . . . 2
Parts Check List . . . . . . . . . . . . . . . . . . . . . . . . 3
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Operation
Controls & Indicators . . . . . . . . . . . . . . . . . . . . . . 7
Loading Labels or Tags . . . . . . . . . . . . . . . . . . . . . 10
Threading The Label Dispenser (Option) . . . . . . . . . . . . 15
AutoSense Gap Sensor Adjustment . . . . . . . . . . . . . . . 17
Cleaning The Print Head . . . . . . . . . . . . . . . . . . . . 18
Introduction to LAB+ Programming
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Command Conventions . . . . . . . . . . . . . . . . . . . . 20
Basic Command Syntax . . . . . . . . . . . . . . . . . . . . 21
Command Editor . . . . . . . . . . . . . . . . . . . . . . . . 21
Command Storage . . . . . . . . . . . . . . . . . . . . . . . 22
Image Buffer . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Image Positioning . . . . . . . . . . . . . . . . . . . . . . . . 23
Unprintable Margins . . . . . . . . . . . . . . . . . . . . . . 23
Font Character Layout . . . . . . . . . . . . . . . . . . . . . 24
Font Scaling . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Command Reference . . . . . . . . . . . . . . . . . . . . 25
Appendix A - Troubleshooting . . . . . . . . . . . . . . . . 39
Appendix B - Accessories . . . . . . . . . . . . . . . . . . 51
Appendix C -ASCII Character Map . . . . . . . . . . . . . 53
980090-001 Rev.B v
Table Of Contents
Getting Started
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Unpacking the Printer . . . . . . . . . . . . . . . . . . . . . . 2
Parts Check List . . . . . . . . . . . . . . . . . . . . . . . . 3
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Operation
Controls & Indicators . . . . . . . . . . . . . . . . . . . . . . 7
Loading Labels or Tags . . . . . . . . . . . . . . . . . . . . . 10
Threading The Label Dispenser (Option) . . . . . . . . . . . . 15
AutoSense Gap Sensor Adjustment . . . . . . . . . . . . . . . 17
Cleaning The Print Head . . . . . . . . . . . . . . . . . . . . 18
Introduction to LAB+ Programming
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Command Conventions . . . . . . . . . . . . . . . . . . . . 20
Basic Command Syntax . . . . . . . . . . . . . . . . . . . . 21
Command Editor . . . . . . . . . . . . . . . . . . . . . . . . 21
Command Storage . . . . . . . . . . . . . . . . . . . . . . . 22
Image Buffer . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Image Positioning . . . . . . . . . . . . . . . . . . . . . . . . 23
Unprintable Margins . . . . . . . . . . . . . . . . . . . . . . 23
Font Character Layout . . . . . . . . . . . . . . . . . . . . . 24
Font Scaling . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Command Reference . . . . . . . . . . . . . . . . . . . . 25
Appendix A - Troubleshooting . . . . . . . . . . . . . . . . 39
Appendix B - Accessories . . . . . . . . . . . . . . . . . . 51
Appendix C -ASCII Character Map . . . . . . . . . . . . . 53
980090-001 Rev.B v

vi 980090-001 Rev.B
vi 980090-001 Rev.B

1
Getting Started
This section provides information on the instal-
lation of the printer and software.
Introduction The LAB+ Series printers are low cost direct
thermal printers specifically designed for print-
ing labels, tags or continuous receipts (with or
without bar codes) from any DOS™or Win-
dows™ or ASCII based compatible computer.
Features •Direct thermal printing for reliability.
•Supports 3 resident font styles.
•Supports 4 types of bar code symbologies.
•High resolution print head for sharp graphics
and text.
980090-001 Rev. B 1
1
Getting Started
This section provides information on the instal-
lation of the printer and software.
Introduction The LAB+ Series printers are low cost direct
thermal printers specifically designed for print-
ing labels, tags or continuous receipts (with or
without bar codes) from any DOS™or Win-
dows™ or ASCII based compatible computer.
Features •Direct thermal printing for reliability.
•Supports 3 resident font styles.
•Supports 4 types of bar code symbologies.
•High resolution print head for sharp graphics
and text.
980090-001 Rev. B 1

Unpacking the
Printer
The printer is shipped in a carton and protec-
tive bag. Keep all packing material in case you
need to move or re-ship the printer. Avoid
touching the electrical connectors to prevent
Electro-Static Discharge damage while setting
up the printer.
The discharge of electrostatic energy that accu-
mulates on the surface of the human body or
other surfaces can damage or destroy the print
head or electronic components used in this
device.
Getting Started
2980090-001 Rev. B
Unpacking the
Printer
The printer is shipped in a carton and protec-
tive bag. Keep all packing material in case you
need to move or re-ship the printer. Avoid
touching the electrical connectors to prevent
Electro-Static Discharge damage while setting
up the printer.
The discharge of electrostatic energy that accu-
mulates on the surface of the human body or
other surfaces can damage or destroy the print
head or electronic components used in this
device.
Getting Started
2980090-001 Rev. B

Parts Check List Your printer kit should contain the items listed
below.
•The LAB+printer.
•The printer Power Supply.
•Printer User’s Guide (this manual).
•1 roll of Sample Labels and Spool.
•1 printer Cleaning Card.
If any items are missing, contact your dealer for
replacement parts.
Getting Started
980090-001 Rev. B 3
Parts Check List Your printer kit should contain the items listed
below.
•The LAB+printer.
•The printer Power Supply.
•Printer User’s Guide (this manual).
•1 roll of Sample Labels and Spool.
•1 printer Cleaning Card.
If any items are missing, contact your dealer for
replacement parts.
Getting Started
980090-001 Rev. B 3

Installation The following sections will step you through the
installation of the printer.
Step ➊
Attach Power
Supply
Place the printer in a suitable location that
allows easy access to printed labels. The printer
should never be operated while resting on it’s
side or upside down. Place the power supply
in a suitable location, preferably on the floor
near an electrical outlet. Check that the printer
power switch is in the OFF (0) position. Attach
the printer power cable to the jack at the rear
of the printer, near the power switch. Check the
label on the power supply for input voltage
requirements. Attach the power supply line
cord to an electrical outlet of the proper volt-
age.
The printer and power supply should never be
operated in a location where either one can get
wet. Personal injury could result.
Getting Started
4980090-001 Rev. B
Installation The following sections will step you through the
installation of the printer.
Step ➊
Attach Power
Supply
Place the printer in a suitable location that
allows easy access to printed labels. The printer
should never be operated while resting on it’s
side or upside down. Place the power supply
in a suitable location, preferably on the floor
near an electrical outlet. Check that the printer
power switch is in the OFF (0) position. Attach
the printer power cable to the jack at the rear
of the printer, near the power switch. Check the
label on the power supply for input voltage
requirements. Attach the power supply line
cord to an electrical outlet of the proper volt-
age.
The printer and power supply should never be
operated in a location where either one can get
wet. Personal injury could result.
Getting Started
4980090-001 Rev. B

Step ➌
Attach Interface
Cable
Parallel Interface
Attach a suitable parallel printer cable from the
computer to the Centronics interface connector
on the rear of the printer.
Serial Interface
Attach a suitable serial printer cable from the
computer to the DB-9 RS-232 Serial interface
connector at the back of the printer. For addi-
tional information on serial cable wiring and
connection parameters, refer to Appendix A -
Trouble Shooting.
Getting Started
980090-001 Rev. B 5
Step ➌
Attach Interface
Cable
Parallel Interface
Attach a suitable parallel printer cable from the
computer to the Centronics interface connector
on the rear of the printer.
Serial Interface
Attach a suitable serial printer cable from the
computer to the DB-9 RS-232 Serial interface
connector at the back of the printer. For addi-
tional information on serial cable wiring and
connection parameters, refer to Appendix A -
Trouble Shooting.
Getting Started
980090-001 Rev. B 5

When the power switch is moved to the ON (1)
position, the Power Indicator should light Red
indicating that the printer is out of paper. If the
indicator fails to light, refer to Appendix A -
Trouble Shooting.
Refer to Section 2 - Operation, for information
on loading labels and using your printer.
Getting Started
6980090-001 Rev. B
When the power switch is moved to the ON (1)
position, the Power Indicator should light Red
indicating that the printer is out of paper. If the
indicator fails to light, refer to Appendix A -
Trouble Shooting.
Refer to Section 2 - Operation, for information
on loading labels and using your printer.
Getting Started
6980090-001 Rev. B

2
Operation
This section provides information on the op-
eration of the LAB+ printers.
Controls &
Indicators
The printer’s power switch is located on the
rear of the unit near the power cord. Placing
this switch in the “1" (ON) position will apply
power to the printer. Place this switch in the ”0"
(OFF) position to remove power when you
have finished using your printer.
The printer is equipped with one front panel
control switch, labeled FEED and one indicator
light labeled POWER. Refer to Figure 2-1.
980090-001 Rev.B 7
2
Operation
This section provides information on the op-
eration of the LAB+ printers.
Controls &
Indicators
The printer’s power switch is located on the
rear of the unit near the power cord. Placing
this switch in the “1" (ON) position will apply
power to the printer. Place this switch in the ”0"
(OFF) position to remove power when you
have finished using your printer.
The printer is equipped with one front panel
control switch, labeled FEED and one indicator
light labeled POWER. Refer to Figure 2-1.
980090-001 Rev.B 7

Power
Switch
Serial
Interface
Connector
Power Connector Figure 2-1
Controls & Indicators
Power
Indicator
Feed
Control
Tension
Release
Push Back
To Release
Operation
8980090-001 Rev.B
Power
Switch
Serial
Interface
Connector
Power Connector Figure 2-1
Controls & Indicators
Power
Indicator
Feed
Control
Tension
Release
Push Back
To Release
Operation
8980090-001 Rev.B

The FEED Control The FEED control can be used in two ways,
tapping or holding. When power is first ap-
plied to the printer, tapping the FEED control
will cause the paper to advance approximately
0.25". This condition is refereed to as a Line
Feed. After printing a label, tapping the FEED
control will cause the paper to advance to the
top of the next label. This condition is referred
to as a Form Feed.
When power is first applied, holding the FEED
control will cause the paper tocontinuously line
feed until the control is released. This mode is
useful when loading labels in the printer. After
printing a label, holding the FEED control will
cause the paper to continuously form feed until
the control is released.
The POWER
Indicator
When the printer is first switched on, the
POWER indicator will glow Red. If labels are
not loaded, the indicator will continue to glow
Red. If labels are loaded, the indicator will
switch to Green, indicating that the printer is
ready for operation.
Indicator
Color Meaning
Green Power On, labels loaded, ready
for use.
Red Power On, out of labels.
Orange Error condition, refer to
Appendix A - Troubleshooting.
Dark Power Off.
If the POWER indicator should fail to light or
glows Red even when labels are loaded, refer
to the Trouble Shooting section in Appendix A.
Operation
980090-001 Rev.B 9
The FEED Control The FEED control can be used in two ways,
tapping or holding. When power is first ap-
plied to the printer, tapping the FEED control
will cause the paper to advance approximately
0.25". This condition is refereed to as a Line
Feed. After printing a label, tapping the FEED
control will cause the paper to advance to the
top of the next label. This condition is referred
to as a Form Feed.
When power is first applied, holding the FEED
control will cause the paper tocontinuously line
feed until the control is released. This mode is
useful when loading labels in the printer. After
printing a label, holding the FEED control will
cause the paper to continuously form feed until
the control is released.
The POWER
Indicator
When the printer is first switched on, the
POWER indicator will glow Red. If labels are
not loaded, the indicator will continue to glow
Red. If labels are loaded, the indicator will
switch to Green, indicating that the printer is
ready for operation.
Indicator
Color Meaning
Green Power On, labels loaded, ready
for use.
Red Power On, out of labels.
Orange Error condition, refer to
Appendix A - Troubleshooting.
Dark Power Off.
If the POWER indicator should fail to light or
glows Red even when labels are loaded, refer
to the Trouble Shooting section in Appendix A.
Operation
980090-001 Rev.B 9

Loading Labels
or Tags
Your printer can print on adhesive backed
labels or non-adhesive tags. Loading either
type of material is easy, however the feed
direction of the roll is different.
If adhesive backed labels are used that do not
lay flat on the liner paper, the exposed edges
may stick to the label guides and rollers inside
the printer, causing the label to peel off from
the liner. Always use high quality, Eltron ap-
proved labels. Supplies can be ordered from
Eltron by calling 1(800) 344-4003.
Before loading labels, insure that the power
supply is connected to a suitable power source
and the printer power switch is in the ON (1)
position.
If you should run out of labels while printing,
Do Not turn the power switch off while reload-
ing or data loss may result. The printer will
automatically resume printing when new labels
are loaded.
Operation
10 980090-001 Rev.B
Loading Labels
or Tags
Your printer can print on adhesive backed
labels or non-adhesive tags. Loading either
type of material is easy, however the feed
direction of the roll is different.
If adhesive backed labels are used that do not
lay flat on the liner paper, the exposed edges
may stick to the label guides and rollers inside
the printer, causing the label to peel off from
the liner. Always use high quality, Eltron ap-
proved labels. Supplies can be ordered from
Eltron by calling 1(800) 344-4003.
Before loading labels, insure that the power
supply is connected to a suitable power source
and the printer power switch is in the ON (1)
position.
If you should run out of labels while printing,
Do Not turn the power switch off while reload-
ing or data loss may result. The printer will
automatically resume printing when new labels
are loaded.
Operation
10 980090-001 Rev.B

Step ➊Open the top cover and remove the spindle
from the printer. Place the spindle inside the
roll of labels or tags.
Cutting the corners off the end of the roll allows
for easier insertion into the feed slot.
If loading labels, place the roll in the top cover
so that the end feeds from the top as shown in
Figure 2-2.
If loading tags, place the roll in the top cover so
that the end feeds from the bottom as shown
in Figure 2-3.
Top Feed
Figure 2-2
Loading Labels
Bottom
Feed
Figure 2-3
Loading Tags
Operation
980090-001 Rev.B 11
Step ➊Open the top cover and remove the spindle
from the printer. Place the spindle inside the
roll of labels or tags.
Cutting the corners off the end of the roll allows
for easier insertion into the feed slot.
If loading labels, place the roll in the top cover
so that the end feeds from the top as shown in
Figure 2-2.
If loading tags, place the roll in the top cover so
that the end feeds from the bottom as shown
in Figure 2-3.
Top Feed
Figure 2-2
Loading Labels
Bottom
Feed
Figure 2-3
Loading Tags
Operation
980090-001 Rev.B 11

Step ➋Adjust the guide tabs to their widest position by
pushing one or both towards the sides of the
printer.
Step ➌Insert the end of the roll into the feed slot
between the guide tabs until resistance is felt
(approximately 3").
Figure 2-4
Open Paper Guides
Figure 2-5
Feed Slot
Operation
12 980090-001 Rev.B
Step ➋Adjust the guide tabs to their widest position by
pushing one or both towards the sides of the
printer.
Step ➌Insert the end of the roll into the feed slot
between the guide tabs until resistance is felt
(approximately 3").
Figure 2-4
Open Paper Guides
Figure 2-5
Feed Slot
Operation
12 980090-001 Rev.B

Step ➍While continuing to gently push the labels into
the feed slot, press the FEED control to ad-
vance labels until the end is visible at the front
of the printer.
Step ➎Press the tension release towards the rear of the
printer and center the labels in the slot. Adjust
the guide tabs so they just touch the edges of
the liner.
Figure 2-6
Press FEED Control
Figure 2-7
Center The Labels
Operation
980090-001 Rev.B 13
Step ➍While continuing to gently push the labels into
the feed slot, press the FEED control to ad-
vance labels until the end is visible at the front
of the printer.
Step ➎Press the tension release towards the rear of the
printer and center the labels in the slot. Adjust
the guide tabs so they just touch the edges of
the liner.
Figure 2-6
Press FEED Control
Figure 2-7
Center The Labels
Operation
980090-001 Rev.B 13

Step ➏Rewind the excess paper onto the roll while
placing the spindle into the holder slots.
Step ➐Tap the FEED control 3 times or until the
POWER indicator glows Green. If you were in
the middle of printing labels, the printer will
automatically resume printing.
Figure 2-8
Place Roll In Slots
Operation
14 980090-001 Rev.B
Step ➏Rewind the excess paper onto the roll while
placing the spindle into the holder slots.
Step ➐Tap the FEED control 3 times or until the
POWER indicator glows Green. If you were in
the middle of printing labels, the printer will
automatically resume printing.
Figure 2-8
Place Roll In Slots
Operation
14 980090-001 Rev.B