ERGO-INNOVATE EI6121 User manual

TV Wall Mount
Instruction Manual V1.0
Model: EI6121
Thank you for choosing this ERGO-INNOVATE product! At ERGO-INNOVATE we
strive to provide you with the best quality products and services in the industry.
Should you have any issues, please don't hesitate to contact at
[email protected].

Solid Concrete
or Concrete Block
CAUTION
DO NOT
install into
drywall alone Wood Studs
(with Drywall)
If you are are not sure the
wall construction, please
contact our product
support line at
support@ergo-innovate.
com.
• Please carefully read all instructions before attempting installation. If you do
not understand the instructions or have any concerns or questions, please
contact our customer service at [email protected].
CAUTION: Avoid potential personal injuries and property damage!
• Do not use this product for any purpose that is not explicitly specified in this
manual. Do not exceed weight capacity. We are not liable for damage or injury
caused by improper mounting, incorrect assembly or inappropriate use.
• This product is designed for use in wood stud, solid concrete, concrete
block and brick walls - DO NOT install into drywall alone.
• The wall must be capable of supporting five times the weight of the TV and
mount combined.
Minimum VESA pattern: 75mm/3 in.(W)x75mm/3 in.(H)
MAX:200mm/
7.9
in.
MAX:200mm/7.9 in.
Check the VESA Pattern of Your TV before the Installation
IMPORTANT SAFETY INFORMATION
If your TV VESA is greater than 200x200 mm/8x8 in. or less than VESA
75x75mm/3x3in., this mount is NOT compatible.
If this mount is NOT compatible, please contact customer service at
[email protected] to find a compatible mount.
Verify Your Wall Construction
100 mm ≈ 4 in
75 mm ≈ 3 in
200 mm ≈ 7 7/8 in
01

3/8 in.(10mm)
Concrete Drill
Warning: This product contains small items that could be a choking hazard if
swallowed.
Before starting assembly, verify all parts are included and undamaged. Do not
use damaged or defective parts. lf you require replacement parts, contact our
customer service at [email protected].
• Please note: Not all hardware included in this package will be used.
Awl
Stud Finder Tape Measure Pencil Drill
5/32 in.(4 mm)
Wood Drill
3/8in.(10mm)
Socket Wrench Phillips Screwdriver
Tools Needed (Not lncluded)
Supplied Parts and Hardware
Supplied Parts and Hardware for Step 1
02 x4
Extender Brackets
01 x1
Faceplate
Bolt
M6 x 12mm
[E1] X4
[E2] X4
Nut
M6
Hammer Level
02

M4 x 30mm
[D2] x4
M6 x 15mm
[D3] x4
M6 x 35mm
[D4] x4
M8 x 15mm
[D5] x4
M8 x 35mm
[D6] x4
M6
M4
M8
M4 x 12mm
[D1] x4
Spacers [If needed]
[Only one bolt size fits your TV]
Washers
TV Bolts
[C1] x4
φ8.5x18x2.5mm
[C2] x4
φ8.5x18x22mm
Note: The bolts are shown in accordance with the actual size
Note: The washers and spacers are shown in accordance with the actual size
Supplied Parts and Hardware for Step 2
04
06
05
[B1] x4
M4/M5
[B2] x4
M6/M8
03

x2
Wall
Anchor
φ10X50mm
This anchor is for con-
crete or brick walls
ONLY. DO NOT use them in
drywall or wood studs.
CAUTION!
Supplied Part and Hardware for Step 3
200 mm
200 mm
100 mm
75 mm
100mm
75 mm
200 mm
100 mm
Arm Assembly/Wall Plate
03 x1
for VESA hole pattern:
75x75mm,100x100mm
for VESA hole pattern:
200x200mm
for VESA hole pattern:
200x100mm
B CA
Note: The lag screw is shown in accordance with the actual size
Lag Screw
ST6x60mm
x2
A1
A2
Step 1 Choose the Combination that Applies to Your VESA Hole
Pattern
04

Bolt length: Verify adequate thread engagement with bolts or bolts/spacers combination.
We recommend thread engagement by at least 5 turns.
-Too short will not hold the TV.
-Too long will damage the TV.
Note: If necessary, the spacers can be used in multi-layer. If the installation fails
after trying various methods, please contact customer service at
[email protected].
Too Short Too Long Correct Correct
Select TV Bolts
M6
M4 M8
Only one bolt size fits your TV.
B C
Attach the extender brackets to faceplate using 4 pcs bolts [E1] and 4 pcs
nuts [E2] for pattern [B] and [C].
E2
E1
02
01
E2
E1
02
01
Secure the Faceplate [01] or Faceplate [01] with
Extender Brackets [02] to TV
Step 2
Note: The small bump on the extender bracket [02] should be aligned with the
hole on the faceplate [01].
05

Option B (For Round Back TV)
D2/D4/D6
B1/B2
C1/C2
06
04
05
CAUTION: Ensure the faceplate [01] or
faceplate [01] with extender brackets [02] is
EQUALLY CENTERED on your TV AND
securely fastened in place.
Option A (For Flat Back TV)
04
(If needed)
03
C1
B1/B2
D1/D3/D5
05
Spacers may be necessary for 2 holes ONLY.
Option C (For TV with A “Bump”)
06
04
05
D1/D3
/D5
B1/B2
06
04
D2/D4/D6
B1/B2
C1/C2 Alternate Spacer Setups
Alternate Spacer Setups
UP
C1/C2
05
06

Option D
For cable interference or inset holes, use
spacers to create extre space between the
TV and faceplate(or faceplate with extender)
)bracket.
05
D2/D4/D6
06
B1/B2
04
C1/C2
05
3A-1 Use a stud finder(not included) to
locate wood studs or use an awl (not
included) to verify the edges. Mark the
edge and center locations.
Awl
(Not lncluded)
Alternate Spacer Setups
Step 3 Attach the Arm Assembly/Wall Plate [03] to Wall
WARNING:
Step 3A Wood Stud Option
X
● Any material covering the wall must not exceed 5/8 in. (16 mm)
● Nominal wood stud size: common 2 x 4 in. (51 x 102 mm) minimum 1½ x
3½ in. (38 x 89 mm)
● Stud center must be verified
●Ensure the arm assembly/wall plate [03] is securely fastened to
the wall before continuing to the next step.
●DONOT USE ANCHOR [A2] FOR THIS STEP!
●Avoid potential personal injury or property damage! DO NOT over-tighten the
lag screws [A1]. Tighten the lag screws [A1] only until the they are pulled firmly
against the arm assembly/wall plate [03].
For wood stud installation, follow STEP 2A
For concrete installation, follow STEP 2B
07

3A-2
3A-3
3A-4
Position the arm assembly/wall plate [03] at
your desired height and line up the holes with
your stud center line. Level the arm
assembly/wall plate [03] and mark the holes.
Drill 2 pilot holes using a 5/32 in.(4 mm)
diameter drill bit. Make sure the depth is
not less than 2 23/64 in.(60mm).
25/64 in.(10 mm)
Socket Wrench
03
ø5/32 in.(4mm)
2 23/64 in.(60mm)
Install the arm assembly/wall plate [03] using
lag screws [A1] . Tighten the lag screws [A1]
only until the they are pulled firmly against the
arm assembly/wall plate [03].
03
UP
UP
WARNING:
●Avoid potential personal injury or property damage! DO NOT over-tighten the lag screws
[A1]. Tighten the lag screws [A1] only until they are pulled firmly against the wall plate.
●Ensure the wall plate is securely fastened to the wall before
continuing to the next step.
● Any material covering the wall must not exceed 5/8 in. (16 mm)
● Mount the wall plate directly onto the concrete surface
● Minimum solid concrete thickness: 203 mm (8 in.)
● Minimum concrete block size: 203 x 203 x 406 mm (8 x 8 x 16 in.)
● Never drill into the mortar between blocks
Wall
Anchor
A2
Step 3B Solid Concrete or Concrete Block Option
08

ø3/8 in.(10mm)
2 9/16 in.(65mm)
Drill 2 pilot holes using a 3/8 in.(10mm)
diameter drill bit. Make sure the depth is
not less than 2 9/16 in.(65mm). Never
drill into the mortar between blocks.
Use the hammer to knock anchors
[A2] into the wall. Be sure the
anchors [A2] are seated flush with
the concrete surface.
Install wall plate using lag screws
[A1] and anchors [A2]. Tighten the
lag screws [A1] only until they are
pulled firmly against the wall plate.
DO NOT over-tighten the lag
screws [A1].
3B-1
3B-2
3B-3
3B-4
Position arm assembly/wall plate [03] at
your desired height, level the wall arm
assembly/wall plate [03] and mark the
pilot hole locations.
25/64 in.(10 mm)
Socket Wrench
03
UP
UP
03
09

Step 4 Secure the TV onto the Arm
Step 5 Tilt Adjustment
W T
T
Tw
Note: Please do not
over-loosen the bolts to prevent
the TV from falling down.
HEAVY! You may need
assistance with this step.
Step 4-1 Remove the preassembled bolts [T] and washers [W] from the arm, and
keep them for the use in step 4-3
Step 4-2 Hang the TV to the arm.
Step 4-3 Tighten the bolts [T] and washers [W]
to secure TV to the arm.
1. Slightly loosen both tilt bolts [T] slightly.
2. Adjust TV to your desired tilt angle.
3. Retighten both tilt bolts [T] to fix the tilt angle.
10

Step 6 Level Adjustment
1. Slightly loosen the preassembled bolt [L] using wrench.
2. Level your TV.
3. Retighten the preassembled bolt [L] using wrench to secure the TV in place.
Thank you again for choosing this ERGO-INNOVATE product!
Note: Please do not-over-tighten or over-loosen the bolt [L].
L
All of us at ERGO-INNOVATE do appreciate your product purchase. We hope
that you are as happy with your product as we are designing and
manufacturing it for you. We strive to provide you with the best quality
products and services in the industry. Should you have any issues, please
don't hesitate to contact us at [email protected].