ERGO-INNOVATE EI6152 User manual

V1.0
Medium Full-Motion TV Wall
Mount Instruction Manual
Model: EI6152
Thank you for choosing this ERGO-INNOVATE product! At ERGO-INNOVATE we
strive to provide you with the best quality products and services in the industry.
Should you have any issues, please don't hesitate to contact at
[email protected].

01
IMPORTANT SAFETY INFORMATION
Check the VESA Pattern of TV before the Installation
Please carefully read all instructions before attempting installation. If you do
not understand the instructions or have any concerns or questions, please
contact our customer service at [email protected].
CAUTION: Avoid potential personal injuries and property damage!
• Do not use this product for any purpose that is not explicitly specified in this
manual. Do not exceed weight capacity. We are not liable for damage or injury
caused by improper mounting, incorrect assembly or inappropriate use.
• This product is designed for use in wood stud, solid concrete,concrete and
brick block walls - DO NOT install into drywall alone.
• The wall must be capable of supporting five times the weight of the TV and
mount combined.
Verify Your Wall Construction
Solid Concrete
or Concrete Block
CAUTION
DO NOT
install into
drywall alone Wood Studs
(with Drywall)
100 mm ≈ 4 in.
200 mm ≈ 7 7/8 in.
400 mm ≈ 15 3/4 in.
300 mm ≈ 11 3/4 in.
Minimum VESA pattern: 100mm/4 in.(W)x100mm/4 in.(H)
If your TV VESA is greater than 400x400 mm/16x16in. or less than
VESA 100x100mm/4x4 in., this mount is NOT compatible.
If this mount is NOT compatible, please contact customer service at
[email protected] to find a compatible mount.
MAX: 400mm/16 in.
MAX: 400mm/16 in.
If you are not sure the
wall construction,
please contact our
technical support line
at
support@ergo-inno-
vate.com.t

02
Tools Needed (Not lncluded)
Supplied Parts and Hardware
Warning: This product contains small items that could be a choking hazard if
swallowed.
Before starting assembly, verify all parts are included and undamaged. Do not
use damaged or defective parts. lf you require replacement parts, please
contact our customer service at [email protected].
• Please note: Not all hardware included in this package will be used.
Stud Finder Tape Measure Pencil Drill
7/32 in. (5.5mm)
Wood Drill
3/8 in. (10mm)
Concrete Drill
3/8 in. (10mm)
Socket Wrench
1/2 in. (13mm)
Socket Wrench
Phillips
Screwdriver
HammerAwl Level
Supplied Parts and Hardware for Step 1
TV Bracket x2
02
Washers (if needed)
Spacers (if needed)
Note: The spacers are shown in accordance
with the actual size
L10mm
x8
C2
L5mm
x8
C1
M6
x4
B

03
Supplied Parts and Hardware for Step 2
x4
A1
Lag Screw
M8x65 mm
Note: The lag screws are shown in accordance with the actual size
Washer
M8
x4
A2
05
M8
M6M4
TV Bolts (Only one bolt size fits your TV)
Note: The bolts are shown in accordance with the actual size
Arm assembly/Wall plate x1
01
Wall
Anchor
This anchor is for con-
crete or brick walls
ONLY. DO NOT use them
in drywall or wood studs.
CAUTION!
x4
A3
x4
F
M4x30mm
x4
D1
M6x15mm
x4
D2
M6x30mm
x4
E1
M8x15mm
x4
E2
M8x45mm

04
Only one bolt size fits your TV.
Step 1 Secure the TV Brackets to TV
Select TV Bolts
Bolt length: Verify adequate thread engagement with bolts or bolts/spacers
combination. We recommend thread engagement by at least 5 turns.
-Too short will not hold the TV.
-Too long will damage the TV.
Note: If necessary, the spacers can be used in multi-layer. If the installation
fails after trying various methods, please contact customer service at
[email protected].
Too Long
Correct Correct
Too Short
CAUTION: Ensure the TV brackets
[02] are EQUALLY CENTERED on your
TV and securely fastened in place.
Option A (For Flat Back TV)
M4 M6 M8
02 02
B
(If needed)
D1/E1/F
C1/C2
(If needed)
Alternate
Spacer
Setups

05
Option D
Option B (For Round Back TV)
Spacers may be necessary for 2 holes ONLY.
Option C (For TV with A “Bump”)
For cable interference or inset holes, use spacers [C1] and [C2] to create extra
space between the TV and TV brackets
02
B (If
needed)
D2/E2/F
C1/C2
02
D1/E1/F
C1/C2
(If
needed)
B
(If needed)
D2/E2/F
C1/C2
B
(If needed)
B
(If needed)
D2/E2/F
C1/C2
Alternate
Spacer
Setups
Alternate
Spacer
Setups
Alternate
Spacer
Setups
Alternate
Spacer
Setups

06
Step 2 Attach the Arm Assembly/Wall Plate [01] to Wall
For wood stud installation, follow STEP 2A
For concrete installation, follow STEP 2B
2A-1
Use a stud finder (not included)
to locate wood studs or use an
awl (not included) to verify the
edges. Mark the edge and
center locations.
16in. (406mm)
Awl
(Not lncluded)
Wall
Anchor
X
A3
Step 2A Wood Stud Option
WARNING:
Ensure the arm assembly/wall plate is securely fastened to
the wall before continuing to the next step.
● Any material covering the wall must not exceed 5/8 in. (16 mm)
● Nominal wood stud size: common 2 x 4 in. (51 x 102 mm)
minimum 1.5 x 3.5 in. (38 x 89 mm)
● Stud center must be verified
Avoid potential personal injury or property damage! DO NOT over-tighten
the lag screws [A1]. Tighten the lag screws [A1] only until the washers
[A2] are pulled firmly against the arm assembly/wall plate [01].
DO NOT USE ANCHOR [A3] FOR THIS STEP

01
A1 A2
07
2A-2
2A-3
2A-4
Position the arm assembly-
/wall plate at your desired
height and line up the holes
with your stud center line.
Level the arm assembly/wall
plate and mark the holes.
Drill 4 pilot holes using a
7/32 in. (5.5mm) diameter
drill bit. Make sure the depth
is not less than 2 9/16 in.
(65mm).
Install the arm assembly/wall
plate [01] using lag screws [A1]
and washers [A2]. Tighten the
lag screws [A1] only until the
washers [A2] are pulled firmly
against the arm assembly/wall
plate [01] .
1/2 in. (13mm)
Socket Wrench
(Not Included)
01
ø7/32 in. (5.5mm)
2 9/16 in. (65mm)
HEAVY! You may need
assistance with this step.
HEAVY! You may need
assistance with this step.

08
Step 2B Solid Concrete or Concrete Block Option
2B-1
2B-2
WARNING:
Ensure the arm assembly/wall plate is securely fastened to
the wall before continuing to the next step.
● Mount the arm assembly/wall plate [01] directly onto the concrete
surface
● Anything covering the wall must not exceed 5/8 in. (16 mm)
● Minimum solid concrete thickness: 203 mm (8 in.)
● Minimum concrete block size: 203 x 203 x 406 mm (8 x 8 x 16 in.)
● Never drill into the mortar between blocks
Avoid potential personal injury or property damage! DO NOT over-tighten the
lag screws [A1]. Tighten the lag screws [A1] only until the washers [A2] are
pulled firmly against the arm assembly/wall plate [01].
Position the arm assembly/wall
plate at your desired height,
level the arm assembly/wall
plate and mark the pilot hole
locations.
01
Drill 4 pilot holes using a 3/8 in.
(10mm) diameter drill bit. Make
sure the depth is not less than 2
3/4 in. (70mm). Never drill into
the mortar between blocks.
Wall
Anchor
A3
ø3/8 in. (10mm)
2 3/4 in. (70mm)
HEAVY! You may need
assistance with this step.

09
01
A1 A2
2B-3
A3
Install the arm assembly/wall
plate using lag screws [A1]
and washers [A2]. Tighten the
lag screws [A1] only until the
washers [A2] are pulled firmly
against the arm assembly/wall
plate. DO NOT over-tighten
the lag screws [A1].
Use the hammer to knock
anchors [A3] into the wall.
Be sure the anchors [A3]
are seated flush with the
concrete surface.
Step 3 Hang the TV onto the Arm Assembly/Wall Plate [01]
1/2 in. (13mm)
Socket Wrench
(Not Included)
HEAVY! You may need
assistance with this step.
01
02
Locking
3-1
3-2
HEAVY! You may need
assistance with this step.

10
Step 5 Tilt Adjustment
Step 4 Level Adjustment
If needed, the TV can be levelled.
1. Slightly loosen the preassembled four nuts [L].
2. Level your TV.
3. Retighten four nuts [L] to hold TV in place.
1. Slightly loosen four tilt nuts [T].
2. Adjust TV to your desired tilt angle.
3. Retighten four tilt nuts [T] to fix the tilt angle.
Tilt adjustment
T
3/8 in. (10mm)
Socket Wrench
(Not Included)
L

Thank you again
for choosing this ERGO-INNOVATE product!
All of us at ERGO-INNOVATE do appreciate your product purchase. We hope
that you are as happy with your product as we are designing and manufactur-
ing it for you. We strive to provide you with the best quality products and
services in the industry. Should you have any issues, please don't hesitate to
contact us at [email protected].