EVOC NPC-8118 User manual

Copyright Notice
Information offered in this manual is believed to be correct at the time of printing, and
is subject to change without prior notice in order to improve reliability, design and
function and does not represent a commitment on the part of the manufacturer. In no
event will the manufacturer be liable for direct, indirect, special, incidental, or
consequential damages arising out of improper installation and/or use, or inability to
use the product or documentation.
This user manual is protected by copyright. No part of this manual may be reproduced,
stored in any retrieval system, or transmitted, in any form or by any means,
mechanical, electronic, photocopied, recorded or otherwise, without the prior written
permission from the manufacturer.
Trademarks
EVOC is a registered trademark of EVOC Intelligent Technology Co., Ltd. Other
product names mentioned herein are used for identification purposes only and may be
trademark and/or registered trademarks of their respective companies.
Please visit our website: http://www.evoc.com for more information,
or send an email to the Technical Support Mailbox [email protected]
(International) or [email protected] (Domestic) for consultation.
Hotline: [phone]

Safety Instructions
1. Please read this manual carefully before using the product;
2. Before inserting, removing or re-configuring motherboards or expansion cards,
first disconnect the computer and peripherals from their power sources to
prevent electric shock to human bodies or damage to the product;
3. Before moving the product, please unplug the AC cable from the power socket;
4. When inserting or removing boards, please firstly unplug the AC power cable;
5. Before connecting or disconnecting any signal cable, make sure all power cables
are unplugged in advance;
6. After turning off the computer, wait at least 30 seconds before turning it back
on;
7. All the operations such as upgrade, remove or installation shall be implemented
on the ESD worktable, because some exactitude components are sensitive to
electrostatic discharge (ESD).
8. If there's no ESD worktable, please take the following measures to prevent
damage from electrostatic discharge (ESD):
a) Wear a antistatic wrist strap and connect it with the metal part of the
corresponding product;
b) Always touch the metal enclosure or frame before touching any
components;
c) Keep part of your body in contact with the metal enclosure to discharge the
static while handling components;
d) Avoid unnecessary movement;
e) Hold the components (especially the boards) by the edges;
f) Place the components on a grounded, static-free operating platform. Use a
conductive foam pad if available (not the component wrapper).
g) Do not let the components slide on the operating platform.
9. Use cross-head screwdriver to operate. A magnetic screwdriver is recommended
(Magnet helps to prevent screws from remaining in the enclosure). Do not leave
any tools or accessories inside the enclosure;
10. Ensure abundant cooling and ventilation.
11. Non-professional personnel are not allowed to open the enclosure.

Contents
Chapter 1 Product Introduction.....................................................................................1
Overview .............................................................................................................1
Main Function .....................................................................................................1
Power Feature......................................................................................................3
Main Performance ...............................................................................................3
Mounting Mode...................................................................................................4
Requirements of Transportation and Storage.......................................................4
Chapter 2 Installation....................................................................................................6
Product Outline....................................................................................................6
Product Appearance and Installation Dimensions ...............................................7
External Connectors ............................................................................................8
Overall Assembly Drawing .................................................................................8
Installing the Cover .............................................................................................9
Installing and Removing the Motherboard ..........................................................9
Installing the Driver...........................................................................................10
Installing the Power........................................................................................... 11
Installing the Fan ...............................................................................................11
Chapter 3 Installing the Drivers..................................................................................13

Chapter 1 Product Introduction
NPC-8118 - 1 -
Chapter 1 Product Introduction
Overview
NPC-8118 is a 1U 19″standard rack-mount network application platform. It contains
Intel® B65/C206/H61 chipset, Supports Intel® Sandy Bridg and Ivy Bridge
Processor in LGA1155 Package. It provides 4x240Pin DIMM(two for H61)on-board
up to 16GB; six Gigabit electric ports and four Gigabit optical ports（H61 has no
optical fiber connector）; one standard PCIe x8 slot, one standard PCI. The product
supports two-group bypass; one 3.5″hard disk and two 2.5″hard disks; ATX single
power as standard configuration; PCIe network expansion; four USB2.0 ports and two
RS-232 serial ports.
Main Function
Microprocessor
Supports Intel® Socket FCLGA1155 package Sandy Bridge CPUs, such as Xeon
E3-1275, Xeon E3-1225, I3-2120 and I5-2500, as well as Ivy Bridge CPUs, such as
I5-3550S, I7-3770 and E3-1225V2 (B65/H61 platform does not support Xeon series).
System Chipset
Intel® B65/C206/H61.
System Memory
Supports 1333/1066MHz DDR3 memory and four memory slots on-board (two for
H61) with dual-channel,Supports 32GB memory in maximum (16GB for H61).
supporting dual channel.

Chapter 1 Product Introduction
- 2 - NPC-8118
Network Function
Provides Six Gigabit electric ports, four Gigabit optical ports（H61 has no optical fiber
connector）and one network module expansion connector on-board. LAN1 supports
Wake-on-LAN function; LAN3 and LAN4 support one group of Bypass function
while LAN5 and LAN6 support the other group of Bypass, four SFP Gigabit optical
LAN ports (only supported by C206 platform).
Display Function
CPU integrates graphics controller, supporting VGA display with the maximum
resolution and refresh rate of 2048x1536@75Hz.
Watchdog Function
255 levels, programmable by minute or second;
Supports watchdog timeout interrupt or reset system.
Expansion Bus
Expandable to one PCIe x8 card, 98.4mm in height and 166.25 mm in length;
complying with PCIe 2.0 standard.
External IO
Two RS-232 serial ports: COM1 adopts RJ45 connector, supporting serial port
redirection function; COM2 provides expansion function in pin headers.
Four USB2.0 ports;
Six Gigabit electric ports and four Gigabit optical ports（H61 has no optical fiber
connector）;

Chapter 1 Product Introduction
NPC-8118 - 3 -
One reserved VGA connector.
Power Feature
Input Voltage/Frequency: 220VAC/50Hz;
Power Consumption of the PC: 42.6 W (Standby); Power Consumption of the
PC: 114 W (100% operate MaxPower);
Note: the power consumption value varies with the board in use.
Main Performance
Mechanical Dimensions, Weight and Environment
Dimensions: 436.5mm (L) x 482.6mm (W) x 43.6mm (H);
Net Weight: 6.6Kg;
Operating Environment:
Temperature: 0°C ~ 45°C;
Humidity: 10% ~ 95% (non-condensing);
Storage Environment:
Temperature: -10°C ~ 60°C;
Constant Wet & Humidity:
Temperature: 40°C, Humidity: 30 ~ 90%RH.
EMC
GB 9254-2008 Radio Disturbance, class A;
GB 9254-2008 Conducted Disturbance, class A
GB/T 17626.2.2006 Electrostatic discharge, level 2;
GB/T 17626.4-2006 Burst Immunity, level 2;

Chapter 1 Product Introduction
- 4 - NPC-8118
GB/T 17626.5-2008 Surge (Impact) immunity, level 2;
GB/T 17626.6-2008 Conducted susceptibility, level 2;
Reliability
MTBF≥50000h
MTTR≤0.5h
Safety
Meets the basic requirements of GB4943;
Mechanical and Environment Adaptability
Vibration: frequency (5 ~ 200Hz), acceleration (1g), amplitude (0.5mm);
Shock: acceleration (10g), duration (11ms);
Mounting Mode
■19″Rack Mount □Desktop □Embedded Panel
□Wall Mount □VESA Standard Arm □Portable
□Others___________
Requirements of Transportation and Storage
Transportation
Well-packaged products are suited for transportation by truck, ship, and plane. During
transportation, products should not be put in open cabin or carriage. During
transshipping, products should not be stored in open air without protection from the
atmospheric conditions. Products should not be transported together with inflammable,
explosive and corrosive substances and are not allowed to be exposed to rain, snow

Chapter 1 Product Introduction
NPC-8118 - 5 -
and liquid substances and mechanical force.
Storage
Products should be stored in package box when it is not used. And warehouse
temperature should be 0°C ~ 40°C, and relative humidity should be 20% ~ 85%. In
the warehouse, there should be no harmful gas, inflammable, explosive products, and
corrosive chemical products, and strong mechanical vibration, shock and strong
magnetic field interference. The package box should be at least 10cm above ground,
and 50cm away from wall, thermal source, window and air inlet.

Chapter 2 Installation
- 6 - NPC-8118
Chapter 2 Installation
Product Outline

Chapter 2 Installation
NPC-8118 - 7 -
Product Appearance and Installation Dimensions
Unit: mm

Chapter 2 Installation
- 8 - NPC-8118
External Connectors
Overall Assembly Drawing
1. Blank Baffle 2. Hanger
3. Motherboard 4. Chassis
5. Fan 6. Hard Disk
7. Cover 8. Power

Chapter 2 Installation
NPC-8118 - 9 -
Installing the Cover
Loosen the two captive screws on the backplane of the chassis, and then pull the cover
backward with force to remove it.
Installing and Removing the Motherboard
Installing the motherboard:
Lay the motherboard at the corresponding position in chassis and fix the board by six
M3 pan head combo screws and three CH-M3-16-5 hexagon copper studs. Install the
turbo fan on the hexagon copper studs and fix it by three M3 pan head combo screws.

Chapter 2 Installation
- 10 - NPC-8118
Removing the motherboard:
Open the cover, loosen the three M3 screws on the turbo fan fixing bracket first, and
then loosen the six M3 screws and three CH-M3-16-5 hexagon copper studs fixing the
motherboard to remove it.
Installing the Driver
Fix the hard disk with the hard disk bracket by four pan head #6-32*1/4 screws, then
put the module at the corresponding position in chassis and fix it by four M4 pan head
screws.

Chapter 2 Installation
NPC-8118 - 11 -
Installing the Power
Lay the power at the corresponding position in chassis and then fix it by four
countersunk head #6-32*1/4 screws from the bottom and rear of the chassis.
Installing the Fan
Fix the two fans with the fan bracket by sixteen ST4.0*10 screws, then put the module
at the corresponding position in chassis, and fix the fan bracket by four M3
countersunk head screws from external of the chassis and four pan head screws from
internal of the chassis.

Chapter 2 Installation
- 12 - NPC-8118

Chapter 3 Installing the Drivers
NPC-8118 - 13 -
Chapter 3 Installing the Drivers
Regarding the installation of the driver program and the detailed information of the
motherboard, please refer to the enclosed CD of the PC.