Vivo STAND-V200L User manual

Dual Ultrawide Vertical Monitor Desk Stand
Scan the QR code with your mobile device or follow the link
for helpful videos and specications related to this product.
Instruction Manual
https://vivo-us.com/products/stand-v200l
SKU: STAND-V200L
[email protected]om www.vivo-us.com 309-278-5303
Chat live with an agent!
GET IN TOUCH | Monday-Friday from 7:00am-7:00pm CST

2
TOOLS NEEDED
44lbs
(20kg)
DO NOT EXCEED WEIGHT CAPACITY.
Failure to do so may result in serious injury.
WARNING!
Phillips
Screwdriver
If you do not understand these directions, or if you have any doubts about the safety of the installation, please call a
qualied technician. Check carefully to make sure there are no missing or defective parts. Improper installation may
cause damage or serious injury. Do not use this product for any purpose that is not explicitly specied in this manual. Do
not exceed weight capacity. We cannot be liable for damage or injury caused by improper mounting, incorrect assembly
or inappropriate use.
WARNING: CHOKING HAZARD
SMALL PARTS - NOT FOR CHILDREN UNDER 3 YEARS. ADULT SUPERVISION IS REQUIRED.
NOTE: SOME HARDWARE MAY NOT BE USED
A (x2)
VESA Plate
B (x2)
VESA Bracket
C (x1)
Base
D (x1)
Lower Pole
E (x1)
Upper Pole
F (x1)
Pole Cap
G (x2)
Cable Clip
H (x4)
Pad
S-A (x3)
M6x16mm
Screw
S-B (x2)
M6x10mm
Thumbscrew
M-A (x8)
M4x12mm
Screw
M-B (x8)
M4x16mm
Screw
M-C (x8)
M5x12mm
Screw
M-D (x8)
M5x16mm
Screw
M-E (x8)
M5 Washer
M-F (x8)
Spacer
T-A (x1)
4mm Allen
Wrench
T-B (x1)
6mm Allen
Wrench
PACKAGE CONTENTS

3
ASSEMBLY STEPS
STEP 1
STEP 2
Install Lower Pole (D) to Base (C) using M6x16mm Screws (S-A) and 4mm Allen
Wrench (T-A). Remove protective lm from Pads (H) and apply them to Base (C) as
shown.
B
C
D
h
T-A
S-A
G
D
T-B
Slide Pole Cable Clip (G) and one VESA Bracket (B) onto Lower Pole (D). Adjust the
height location of VESA Bracket (B) and tighten using the 6mm Allen Wrench (T-B).

4
STEP 3
STEP 4
Press Pole Cap (F) into Upper Pole (E), using the side without internal threading .
Screw Upper Pole (E) onto Lower Pole (D). Slide remaining Cable Clip (G) and VESA
Bracket (B) onto Upper Pole (E). Adjust the height location of VESA Bracket (B) and
tighten using the 6mm Allen Wrench (T-B).
EF
G
B
E
T-B

5
STEP 5
Mount VESA Plates (A) to monitors using appropriate Screws (M-A thru M-D), M8
Washers (M-E), and Spacers (M-F).
A
A
STEP 6
Slide monitors with VESA Plates onto VESA Brackets (B) and secure using M6x10mm
Thumbscrew (S-B).
S-B
B

6
WARNING
STEP 7
Use Cable Clips (G) to route cables.
Store Allen Wrenches (T-A, T-B) in
slots of Clips.
Always keep monitors positioned over the desktop within the arrow range shown.
G
T-B
T-A

7
ADJUST AS DESIRED
Use 6mm Allen Wrench (T-B) to loosen or tighten Monitor Bracket (B) tension.
T-B
B

LAST UPDATED: 03/08/2023
REV1
Open Monday - Friday 7:00am - 7:00pm CST,
our dedicated support team can oer immediate assistance with rapid response times. If any
parts are received damaged or defective, please contact us. We are happy to replace parts to
ensure you have a fully functioning product.
FOR MORE VIVO PRODUCTS, CHECK OUT OUR WEBSITE AT: www.vivo-us.com
[email protected] AVG. RESPONSE TIME (within oice hrs): 1HR 8M
- 23% within < 15m
- 38% within < 30m
- 61% within < 1hr
- 83% within < 2hr
- 92% within < 3hr
Love your new VIVO setup and want to share?
Tag us in your photo! @vivo_us
AVG. RESOLUTION TIME (within oice hrs): < 15 M
www.vivo-us.com
Chat live with an agent!
AVG. RESOLUTION TIME (within oice hrs): 5M 4S
309-278-5303