EZPOLE CLASSIC User manual

Instructions for the CLASSIC Sectional Flagpole
Tools & Material Needed:
l Post Hole Digger/Shovel
l Level
l Tape Measure
l Mixing Container
l 80 lbs. + of Quick Setting Cement
l Approximately 3”of Gravel
Flagpole Kit Includes:
l Aluminum Ground Sleeve
l Aluminum Gold Ball
l 3 to 5 Aluminum Flagpole Sections
(Depending on Size—13’ 3 sections, 17’ 4 sections, 21’ 5 sections)
l Truck Top installed to Top Section and pre-strung with
rope
l Section with installed Cleat
l 3’ x 5’ Nylon Sewn USA Flag
(*Note not all vendors add ag)
l Clip Pack: 4 nylon clips and ag etiquette leaet
l Manufacturer Product Warranty Registration
(Must be Returned within 90 Days of Purchase or
Warranty is Void)
See back for assembly instructions including how to y at half-mast.
STEP 1: Select agpole location. Call 811 before you dig. Check for
underground sprinklers, water and electrical lines. Make sure your ag
has clearance to y in all directions. Are you too close to the house?
Watch the roof!
STEP 2: Dig a hole approximately 26” deep by 12-18” in diameter (26”L x
12-18”W).
STEP 3: Place approximately 3”of gravel in hole to allow for drainage.
STEP 4: Place aluminum ground sleeve into gravel – to prevent concrete
from owing inside.
STEP 5: Mix cement and pour around ground sleeve. Repeat until hole is
lled (the more cement the better). It is OK to have your ground sleeve
an inch or two above ground level. Can be lled in with mulch, dirt and/
or ower bed.
STEP 6: Carefully insert pole section swedge end up into ground sleeve
as cement will be wet . Use a level to make sure pole is straight. Remove
pole section after level, concrete must cure for at least 24 hours.
STEP 7: Assemble your agpole. Flip over for proper assembly
instructions.
STEP 8: Insert agpole into ground sleeve! Enjoy!
Manufacturer suggests taking agpole down during high winds and strong storms also
storing agpole during winter for those in aected regions.
FOR PARTS AND SERVICE:
EZPOLE FLAGPOLES/ 1489 EAST 363RD STREET/ EASTLAKE, OHIO 44095
TOLL FREE: 888-454-9164/ LOCAL: 440-951-1011/ FAX: [phone]/ www.ezpole.com
26”
12-18”
In Ground
Sleeve
Gravel
6-8”
3”
Concrete

Assembly Instructions
Classic Sectional Flagpole
Flying Your Classic Flag at Half-Mast
*To y your ag at half-mast on your Classic Sectional agpole, lower your
ag to half the height of the agpole with rope.
The bottom of the flag attaches to
the rope with a second nylon clip.
The top of the flag attaches to
rope with nylon clip.
Assembly Instructions
Classic Sectional Flagpole
Attaching Nylon Clip to Halyard:
l Bring halyard through loop (as show above) at the mid-length of the
halyard
l Attached the second nylon clip 36” (inches) below rst nylon clip.
l Tie the halyard together after pole assembly is put together and
placed upright. Latch halyard to cleat to secure.
Pole Assembly Order from Ground (Bottom) to Top:
l 13’ - Plain Section, Section with Cleat, Top Section
l 17’ - Plain Section, Section with Cleat, Plain Section, Top Section
l 21’ - Plain Section, Section with Cleat, Two (2) Plain Sections,
Top Section
Once Ground Sleeve has been installed and had proper time to cure,
you can assemble your agpole.
The Top Section with Truck Top installed and pre-strund with rope
will go at the very top of the agpole.
Section with cleat is to be insalled second from the bottom.