Finelite HP-4 Recessed User manual

Conduit T-Bar
FINELITE
© 2015 FINELITE, INC. ALL RIGHTS RESERVED. Form 98161. 10/15
Step 1
Remove lens and set aside to prevent it from getting dirty
or damaged.
HP-4 Surface Mount T-Bar Starter/Independent Installation Instructions
Lens
Step 7
Reinstall lens. Turn power on to fixture.
#8-18x1/4"
Screw(provided)
Step 6
Insert wires through jam nut and install jam nut onto conduit connector. Make wiring connections.
Replace trap door and fasten with #8-18 x 1/4" screws (provided).
Step 5
Cut hole in ceiling tile for conduit to pass through. Insert wires
and conduit through ceiling tile and into fixture feed hole.
1/4"-20 Thread Hole
New Feed Hole
6"
Step 2
Note new feed hole on fixture as indicated above.
2.00"
0.67"
1.00"
A"
Secure to Structure
(by others)
Step 3
Install caddy clips accordingly. Secure fixture to structure using
tie-wire (supplied by others) according to code.
Caddy Clips
1/4"-20 Threaded Stud
Caddy Clips
1/4" Washer
1/4"-20 Nut
1/4" - 20 Threaded Stud
Step 4
Remove #8-18 x 1/4" screw (provided) to open trap door and install fixture
onto caddy clips with 1/4"-20 Nut and 1/4" washer onto 1/4"-20 threaded
stud. Repeat this step on the other end of the fixture.
Conduit
Caddy Clip
Feed Hole
Hole Cut
In Ceiling Tile
Ceiling Tile
T-Bar
Dimming
(Gray)
Dimming
(Purple)
Wire Nut
Dimming (Gray)
Dimming (Purple)
Jam Nut
FIXTURE LENGTH ' A '
4' 36"
8' 84
12' 132"
MOUNTING HOLE LOCATION TABLE
#8-18 x 1/4"
Screw (provided)
rotected by one or more US atents: 8915613; D702,391; D702,390; D700,732
Finelite, Inc. • 30500 Whipple Road • Union City, CA 94587-1530 • 510 / 441-1100 • Fax: 510 / 441-1510 • www.finelite.com
Note: All power connections to be installed to
local/national codes by a Certified Electrician.

FINELITE
© 2015 FINELITE, INC. ALL RIGHTS RESERVED. Form 98162. 09/15
HP-4 Surface Mount T-Bar Joiner Installation Instructions
Starter
Joiner/Ender
Aligner Sleeve
Plug Together Wiring
Reinstall lens. Turn power on to fixture.
Step 4
Connect Plug Together Wiring. Slide Joiner fixture to Starter and
be careful not to damage any wiring.
Step 2
Remove lens and set aside to prevent it from getting dirty
or damaged.
Starter Distance
Secure to Structure
(by others)
Joiner Distance
A"
B"
Step 1
Install caddy clips for Joiner accordingly. Secure fixture to structure using tie-wire
(supplied by others) according to code.
Starter
Joiner
Step 3
pen trap door by removing #8-18 x 1/4" screw (provided) on the side of the trap door and move Joiner next to Starter.
Caddy Clips
1/4" Washer
1/4"-20 Nut
1/4" - 20 Threaded Stud
Trap Door
#8-18 x 1/4" Screw
(provided)
Step 5
Install fixture onto caddy clip with 1/4"-20 Nut and 1/4"
washer onto 1/4"-20 threaded stud. Replace trap door
and fasten with #8-18 x 1/4" screws (provided).
End Brackets
#8-18 x 1/2" Combo Hex
Screw (provided)
Joiner/Ender
Starter
Step 6
Secure joint with 2 #8-18 x 1/2" Combo Hex Screws (provided).
Screws can be installed from the left or right.
Joiner
Starter
Step 7
FIXTURE LENGTH 'A' (IN) 'B' (IN)
4' 36 48.00
8' 84 96.00
12' 132 144.00
MOUNTING HOLE LOCATION TABLE
#8-18 x 1/4"
Screw (provided)
Protected by one or more US Patents: 8915613; D702,391; D702,390; D700,732
Finelite, Inc. • 30500 Whipple Road • Union City, CA 94587-1530 • 510 / 441-1100 • Fax: 510 / 441-1510 • www.finelite.com
Note: All power connections to be installed to
local/national codes by a Certified Electrician.
IMPORTANT STEP