FIVES NORTH AMERICAN H6415-DSP User manual

H6415-DSP (REMOTE USER INTERFACE)
SYMBOL DEFINITION KEY
Amplifier in automatic mode;
blinks when the line-run relay input
is energized in automatic.
Amplifier in
manual mode.
Amplifier in servo center mode.
User keys
(see below).
Detector Select: Selects the detector or
detectors used for control: edge 1 allows
guiding from detector 1 only, edge 2 from
detector 2 only, and center guide from both
detectors.
Web Setup: In this mode, the amplifier is informed
of the detector(s) and web characteristics. 1) Press
manual key. 2) Press this key. 3) Pass the web
material fully into, then fully out of the detector's
field of view. Do not let fingers or printing on
the web enter the field of view. 4) Press key
again. If pressed accidently, press any green key
to escape.
Servo Center: Switches control to servo center.
In servo center, the actuator travels to a preset
center position. Exit servo center control by press-
ing either manual or automatic.
Manual Control: Switches control to manual, al-
lowing the operator to jog (reposition) the actuator.
Jog using the arrow keys. Exit manual by pressing
automatic or servo center .
Automatic Control: Switches control to auto-
matic. Exit automatic by pressing either manual
or servo center.
Left Jog Key: Used to manually jog the actuator
left or to decrease the gain.
Right Jog Key: Used to manually jog the actuator
right or to increase the gain.
Gain: Used to adjust the control response. Press
this key, then use the arrow keys to increase or
decrease the system response (0-999). Press
again to accept the value and to exit this mode.
Det 1 Guide
Lit when the system is
guiding with detector 1
(edge 1).
Center Guide
Lit when the system is
guiding with both
detectors (center guide);
blinks when in web setup.
MAINT. SHEET 10028
MS-17.00
GUIDING SYSTEMS January 2000
Displays either the gain or
a system status code.
Bar graph indicates relative strip
position. Middle block shows the
ideal web position. Gain Adjust Mode Indicator.
Det 2 Guide
Lit when the system is
guiding with detector 2
(edge 2).
H6415

Steering Guide with
Integral Actuator
Alarm Output
(N.C. and N.O. Contacts Provided)
H6415-AMP or H6425-AMP
(controller)
115/230 V ac
L1
External Servo Center
(close to force Servo Center)
Optional Second
H6415-DSP Remote
Interface or Customer's
EIA-485 Serial Device
H6415-DSP
Remote Interface
Detector 2
H6415-OFS
Remote Offset
External Line-Run Relay
(open when line running)
Optional Posi-
tioner
SimPlexTM Quick Start Assistance Sheet
FNA 8-07-MS10028-17.00
H6415 H6425
Manual Manual
Step Action Page # Page #
1Mount the H6415-DSP remote(s). 5-6 5-6
2Mount the H6415-AMP or H6425-AMP. 7 7
3Mount the detector(s). 25 25-37
4Wiring
Plug in the actuator connector 10 10
Plug in the detector connector(s) 10 10
Plug in the H6415-DSP remote(s) connector(s) 10 10
Set voltage select switch (SW201) in the controller 12 8
Wire ground (GND) and AC power connections 8-9 8
5If communicating with more than one H6415-DSP or through a 20 20
computer, then define the primary interface with (SW101) in the
H6415-DSP; otherwise, skip this step.
6Perform Web Setup Procedure: Web Setup, Verify Guide Sense,
Adjust Gain, Verify Servo Center Sense. 13-14 13-14
7Select Edge 1 (guide with detector 1), Edge 2 (guide with
detector 2), or Center Guide (guide with both detectors). 22 22
MS10028/17.00
Page 2
Typical System Configuration
Detector 1
The following quick start guide includes only the essential configuration options. To further customize your
system--for example, to use optional external connections--see Section 2, Installation/Wiring and Section 3,
Setup in the SimPlex H6415-AMP-00 User's Manual.
Fives North Amercian Combustion, Inc., 4455 East 71st Street, Cleveland, OH 44105 USA, Phone [phone]
Fax [phone] email: fna.guiding@fivesgroup.com • www.fivesgroup.com/fivesna