30.5 mm
30.5 mm
36 mm
39.5 mm
F7
Flight Control
02 Part list / Install Dimensions
05 Attentions
01 Specifications & Main features
03 Ports diagram
T0wer
X2
www.flycolor.net
CONF IGUR ATOR 10.7.0
Zadig 2.3.701
List All Devices
Ignore Hubs or Composite Parents
Create a Cata log Fil e
Sign Catalo g&Ins tall Aut o generated certificat e
Advanced Mo de
Log Verbosit y
04 Load firmware for FC
F11
Zadig 2.3.701
STM32 BOOTLOADER
ST Tub30(v3.0.4.0)
0483 D
X
8 devices found
Replace Driver
Options
● F7 Flight Control 1 x
● Silicone vibration absorber 4x
O-Ring x ● 4
● ESC /FC connecting wire 1x
L wire 4x● ED
ATTENTION
TOP
BOTTOM
251400-1132 V1.0
User Manual
Flight Control
ATTENTION
Thank you for using our product. Any Improper operation may cause
personal injury damage to the product and related equipments. This
high power system for RC model can be dangerous ,we strongly
recommend reading the user manual carefully and completely.
We will not assume any responsibility for any losses caused by
unauthorized modifications to our product. We have the right to
change the design, appearance, performance and usage require-
ments of the product without notice.
*All pictures are for reference only
● LiPo cells:3-6S.
● Weight:9.5g (Without accessories).
● Demension:39.5x36x7.8mm.
● Install holes:30.5x30.5mm,M3.
● Betaflight F C firmware:S TM32F7X2 :FLY COL OR F7);(Config. .
● Betaflight F C board:FLYCOL ORF7.
● MCU:ST M32F722.
● Gyro MP U-6000 S PI.：
● Bluetooth：F C_Bluetooth.
● USB: Type C.
● Supports SBUS,SP EKT RU M1024/2048 etc. remote control / receiving
mode.
● FC integrated 3.3V,5V, 12V for receiver, V TX, camera, buzzer, LED
and other peripheral devices.
● 4-way led port, independent 5V BE C power supply, making the power
supply more safe and reliable.
● Supports Betaflight Configurator to adjust the LE D color.
● For these quick plug cables, please confirm the wire sequences on your devices’
connector are corresponding with the Flight control’s before connecting. If the
terminals are not fit your devices ,please make a modified connection to fit.
● Please ensure enough safety space between the FC& ESC or other devices, as
short circuit will damage the product.
5V
3.3V
GN D
RX3
TX3
TX6
RX6
5V
GND
GN D
Vbat in
S4
S3
S2
S1
CRT
FCCM To camera OSD port
Boot Type C B+ B-
GND
GND
TX5
RX5
5V
10V
CAM
VTX
TX1
RX1
*5V
GN D
RS SI
Spare pad
To ESC
USB
*5V：5V output here after inserting USB, (it is convenient to debug the receiver without power
on); the other 5V / 10V ports need battery power before voltage output.
GND
GND
TX5
RX5
5V
10V
CAM
VTX
Rx1
GN D
RX2
TX2
GN D
10V
LED
5V
GND
LED
5V
GND
LED
5V
GND
LED
5V
GND
TX1
RX1
5V
GN D
RS SI
To ESC
GND
GND
Vbat in
NC
S4
S3
S2
S1
CRT
RX6
GND
NC
GND
1# signal
2# signal
3# signal
4# signal
Current meter
Vbat Input
RX6
You need to use DFU mode to recover firmware for Flight control, and need
a software tool called Zadig to replace the driver for you FC when you load
firmware at the first time.
1.Start the Zadig software tool;
2.Press and hold the “BOO T” on the FC, connect the F C to the PC.
3.Click “Options”,and select “List All Devices”.
4. Then select “S TM32 BOO TL OADER ”,Then click “Replace Driver”
5. Close the Zadig software tool when replace successfully, Then disconnect the
FC from the P C.
（Notice：If you've run the above steps before, then you don't need to repeat,
starting directly from the 6th step）
6. Start the Betaflight on the P C; Press and hold the “BO OT” on the FC , connect
the F C to the PC , then the F C is connected in the “D FU” mode, then you can
load the firmware;
7.You can load the firmware online or local：
1) Local(recommended, it needs to download in advance or ask for Flycolor)：
First load the STM32f7x2.hex file, then connect and input the contents of
FLYCO LO RF7.config file in the CL I ,and enter “save”.
2) Online: Select F C board ,and select the correct firmware FLY CO LO RF7
version for the board, then load the firmware online.
●Please don't load any other firmware or config. for Flight Control .
●The Bluetooth port is fixed as MSP of UART4.
●SBUS and Spektrum receivers are applicable to all UART ports (except
UART4, which is fixed to Bluetooth). It is required to manually turn on the
“Serial RX” of the required UART port.
●UART6 is recommended for telemetry port, which can be directly
connected with ESC / Flight Control connecting wire.
●Flight Control should be far away from all magnetic materials.
●If there is any deviation between the detected voltage/current with actual
situation, you can adjust the scale value in the Betaflight-Power&Battery
●5V ,10Vsupply is for low-current use only(5V 3A MAX, 10V 1.5mA MAX).
●Please ensure that all wires and connecting parts are well insulated to
avoid product damage due to short circuit.
●Never use this product in harsh environments such as humidity, high
temperature, and so on to avoid product damage.
●Please contact Flycolor sales or technical support for more information.
