FRAME IT ALL 300001228 User manual

300001228/300001232
300001369 (Sandbox Canopy/Cover)
300001370/300001515 (Sandbox Canopy/Cover)
HEXAGON
SANDBOX
7’ x 8’
Customer Service: 1800-914-9835 | [e-mail]
© 2020 Frame It All. All Rights Reserved.
Tools needed: Hammer (to tap stake in place), Hackshaw (optional)
2 LEVELS SANDBOX KIT CONTAINS:
Composite
Timbers x 12
Stacking
Brackets x 24
Stake
x 12
Plugs
x 48
Caps
x 6
Kit with Sandbox Canopy/Cover combo
will have the additional items below.
SKU# 300001370|300001515
Liner x 1
SKU# 300001228|300001232
Sandbox Canopy
/Cover x 1
Telescoping
Pole x 6
1 LEVEL SANDBOX COMBO KIT CONTAINS:
Composite
Timbers x 6
Stacking
Brackets x 12
Stake
x 6
Plugs
x 24
Caps
x 6 Liner x 1
SKU# 300001369
Sandbox Canopy
/Cover x 1
Telescoping
Pole x 6
2 LEVELS
Layout your timbers
along the borderline and
connect each timber
together by inserting the
top of the stake through
the bracket loops with
the stake pointing to the
sky. This enables you to
freely position your
border to get your
desired location.
1 LEVEL
Caps
x 6
Triangle Cardboard Gauge is included! DO NOT THROW IT AWAY!

Customer Service: 1800-914-9835 | [e-mail]
ASSEMBLY INSTRUCTIONS
STEP 1:
For one level, assemble 6 x Doubled-Bracket Timbers (A)
For two levels, assemble 12 x Doubled-Bracket Timbers (A)
Attach one single stacking bracket to each end of timbers (one facing up, one facing
down – shown above)
STEP 2: Place liner in desired location and lay it flat. Arrange timbers to create a
hexagon shape, using 6 (A) timbers. Connect all the bracketed timbers with the stake
upside down so that the timbers can be angled easily. Use the as a guide to
make the interior angle of 120 degree (refer to diagram below). Once the 1st level is
lined up, hammer stakes through brackets to secure the level.
X 6
X 12
Use plugs (included)
to cover the holes on
both side of timbers
STEP 2a: For one level, add caps to each
of the top corner joints to finish off the
sandbox and plugs to cover the holes on
both side of timbers.
IMPORTANT: The plugs & caps ARE
NOT CHILD/BABY-PROOF. Secured the
plugs & caps with glue.
Put stakes
upside down
X 6
Use the as a guide to create
120 degrees
Note:
If you plan to assemble raised
bed on a hard surface, use
hacksaw to remove the spike of
each stake. Use these cut down
stakes for the base level only of
your raised garden.
Trim stake spike with
hacksawfor use indoor
or on hard surfaces

Customer Service: 1800-914-9835 | [e-mail]
ASSEMBLY INSTRUCTIONS – For Product with Second Level only
STEP 3: Once 1st level is secured, assemble 2nd level using 6 (A) timbers and the
stacking stakes. Insert one stake through the brackets into the hole on top of the stake
beneath it to lock the second level in place.
Use plugs (included)
to cover the holes on
both side of timbers
Use plugs to cover
the holes – two
plugs are required
per bracket (1 on
each side)
Use a Finishing
Cap to complete
the top level.
Use an Anchor
or Stacking Joint
for ground level
frames or borders.
Use only Stacking
Joints when
creating additional
levels.
When creating a
multi-level frame
use a Stacking
Joint.
Stacking Joints fitinto
the tops of Anchor
Joints and other
Stacking
Joints
How the Joints Work
STEP 4: Add the caps to each of the top corner joints and plugs to cover the holes on
both side of timbers to finish off the sandbox.
NOTE: Before flipping the stake around and hammering into the ground to
permanently pin the 1st level, line up the 2nd level to make sure the bottom level is
positioned properly.

ASSEMBLY INSTRUCTIONS – For Telescoping Hexagon
Canopy/Cover
FORMING THE CANOPY DOME
STEP 1: In an open area, position the
canopy so that the inside of the canopy
(with canopy supports showing) is facing up.
INSTALLING THE TELESCOPING SUPPORT POLES
STEP 1: Unlock the clamps on the bottom two of the telescoping pole and extend it to
its full length. Lock the clamps to hold it in place.
extend
STEP 2: Remove existing caps from stakes
and replace it with caps that have holes to
receive the poles.
STEP 3: Insert widest end of the pole
into recess of staking joint stakes –
repeat with remaining poles.
STEP 2: Manually expands the canopy
spokes evenly in each direction as much
as possible.
STEP 3: Using your foot, step on the center hub of the canopy to invert and lock the
supports in place. The canopy will ‘flip’ into its proper convex shape and become stable
–refer to image below.
Customer Service: 1800-914-9835 | [e-mail]

ASSEMBLY INSTRUCTIONS – For Telescoping Hexagon
Canopy/Cover
ATTACHING THE CANOPY (NOTE: 2-person job to make it much easier)
STEP 1: Position canopy top so that canopy connectors are aligned with support poles.
STEP 2: Insert support pole into canopy connector cap
(refer to image on left).
Repeat with remaining poles.
STEP 3: Extend the top telescoping to its full length.
STEP 4: Pull canopy flaps together at each corner and
affix with Velcro straps.
TO CONVERT TO SANDBOX COVER
Release the highest clamp on each pole.
Canopy will now slide down to the next
set of levels. Lock 1st lever, then repeat
with each additional level of clamps
until the poles have fully telescoped
into each other.
TO CONVERT BACK TO CANOPY
Release each bottom set of levers, then
extend and lock 1st level of telescoping
poles.
Repeat with each additional level.
STORING THE CANOPY
STEP 1: Remove canopy from telescoping poles. Place on ground right side up (as it
came off the support poles.
STEP 2: Using your foot, step on the central
hub to invert and unlock the canopy
supports.
STEP 3: Compress canopy sides together
to close.
Customer Service: 1800-914-9835 | [e-mail]