Freetime ROCKFORD RS4212 User manual

Check all packaging before discarding.
Be sure all parts identied in the assembly manual
are included.
Don't assemble if parts are missing.
If you are missing parts or have questions please contact
our toll free line at 1-888-620-6088.
FREETIME FUN
1830 E. FABYAN PKWY.
BATAVIA, IL 60510
WWW.FREETIMEFUN.COM
BEST IN GAMES, SAUNAS,
POOL AND PATIO
12' TWO PIECE SHUFFLEBOARD TABLE - RUSTIC OAK
ROCKFORD
RS4212

2
Thank you for purchasing this product. If you experience any issues during assembly or use of this
product, please don't hesitate to contact Customer Service at 1-888-620-6088 for immediate assistance.
ASSEMBLY TIPS
IMPORTANT! PLEASE READ THESE ASSEMBLY INSTRUCTIONS IN ENTIRETY BEFORE ASSEMBLING
YOUR PRODUCT.
Estimated Assembly Time: 3 hours.
1. Find a clean, level surface to begin the assembly of your game table. Assembly will require two adults. You
may want to carefully cut the four corners of the box so that the bottom of the box can be used as your
work surface.
2. Remove all of the contents from the box and verify that you have all of the parts shown on the Parts List
before you begin assembly. Note: Some parts are pre-installed or pre-assembled.
3. When installing parts that have more than one screw or bolt, hand tighten all screws or bolts in
place before nal tightening with a screwdriver or wrench.
4. Electric screwdrivers may be helpful during assembly; however, please set a low torque and use extreme
caution because screws may be stripped if overtightened, resulting in damaged parts.
THIS PRODUCT IS INTENDED FOR INDOOR USE ONLY. WE DO NOT RECOMMEND MOVING THE TABLE ONCE IT HAS BEEN FULLY
ASSEMBLED. IF YOU DO HAVE TO MOVE THE ASSEMBLED TABLE, WE STRONGLY SUGGEST THAT YOU DISASSEMBLE THE TABLE
TO MOVE IT. DO NOT DRAG THE TABLE WHEN MOVING IT AS THIS MAY CAUSE DAMAGE TO THE LEGS.
HARDWARE PACK RB4212 - H
XRS42028 - Box B
11 14 15 16 17 20
Screw 4" x 11⁄2"(8) Bolt 5⁄16" x 11⁄4"(9) Bolt 5⁄16" x 3⁄4"(24) Bolt 5⁄16" x 2" (9) Washer 5⁄16" x 3⁄4"(42) Bolt 1⁄4x 11⁄4(24)
21
30 36
22
33 37 38
23 24 28 29
Bolt 1⁄4" x 1" (8) Screw 5⁄16" x 11⁄4"(32) Bolt 1⁄4" x 3⁄4"(12) Bolt 5⁄16" x 25⁄64"(6) Washer 9⁄32" x 17⁄64"(4) Nut 15⁄32" (4)
Washer 1⁄4" x 5⁄8"(44) Screw 1⁄8" x 1⁄2"(4) Rod 5⁄16" x 51⁄2'(2) Washer 5⁄16"(4) Nut 5⁄16"(4)

3
44 45
ROCKFORD 12' TWO PIECE SHUFFLEBOARD TABLE
ACCESSORIES
39 41 42A 42B 43
Shueboard Brush
XRS42022 (1) - Box B
Wax
XRS42024 (1) - Box B
Red Pucks
XRS42025 (4) - Box B
Blue Pucks
XRS42026 (4) - Box B
EVA Bumper Cushion
XRS42027 (2) - Box B
TABLE PARTS
1 2 3 4 5 6
Cabinet Half
XRS42001 (2) - Box A/B
Side Table Frame #2
XRS42002 (2) - Box A
Side Table Frame #3
XRS42003 (2) - Box A
End Table Frame
XRS42004 (2) - Box B
Playeld Half
XRS42005 (2) - Box A
Leg
XRS42006 (3) - Box B
7 8 9 10 12 13
Leg Top Cap
XRS42007 (3) - Box A
Leg Base
XRS42008 (3) - Box A
Center Support Beam
XRS42009 (2) - Box B
Center Support Plate
XRS42010 (1) - Box B
Wood Plug
XRS42011 (4) - Box B
Slide Scorer
XRS42012 (2) - Box B
18
32
19
34
25
35
26 27 31
40
Top Leg Bracket
XRS42013 (6) - Box B
Leg Leveler
XRS42014 (6) - Box B
Top Metal Plate
XRS42015 (3) - Box B
Inside Metal Plate
XRS42016 (6) - Box B
360mm
Connection Rod
XRS42017 (2) - Box B
Climate Adjuster
XRS42018 (4) - Box B
Center Frame Trim
XRS42019 (2) - Box B
Brass Tenon
XRS42020 (4) - Box B
19mm Wrench
XRS42021 (2) - Box B
4mm Allen Wrench
XRS42023 (1) - Box B
12mm Wrench
XRS42030 (2) - Box B
5mm Allen Wrench
XRS42029 (1) - Box B

4
ROCKFORD 12' TWO PIECE SHUFFLEBOARD TABLE ASSEMBLY INSTRUCTIONS
NOTE:
It is recommended that you assemble and position the table in the location/room that it will be
utilized in.
We do not recommend moving the table once it has been fully assembled. If you do have to move the
assembled table, we strongly suggest that you disassemble the table to move it.
If you must move the
assembled table, we
suggest that four strong
adults assist in the
moving process. Position
one person at each end
of the table and two
people at the center of
the table on each side,
it is critical to support
the center play surface
area to avoid stress and
possible damage to the
2-piece surface design.
STEP 1
• Align the pre-drilled holes in the leg base #8 with the pre-drilled holes located on the bottom of leg #6.
Attach the leg base #8 to the leg #6 with bolt #16 and washer #17.
• Rotate the leg to the upright position. Align the pre-drilled holes in the leg top cap #7 with the pre-drilled holes
located on the top of the leg #6. Attach the leg top cap #7 to the leg #6 with bolt #14 and washer #17.
• Align the top leg bracket #18 with the pre-drilled holes located on the leg top cap #7.
• Attach the top leg bracket #18 to the leg top cap #7 with bolt #15 and washer #17.
Note: DO NOT fully tighten the bolts at this time; the top leg brackets will need to be slightly adjusted in
a later step to align the pilot holes in the table frame with the holes in the bracket when attaching the
legs to the frame.
• Repeat this process for all three legs.
#16
#8
#6
#17
#6 #6
#7
#14
#17
#7
#15
#17
#18

5
STEP 3
• Cabinet Base A - Insert a leg assembly into the Cabinet frame and check the leg bracket hole alignment to make
sure they are in proper alignment with the pre-installed inserts located on the inside wall of the Cabinet. Remove the
leg assembly from the Cabinet frame and adjust the leg bracket as needed, rmly tighten the #18 leg brackets into
position. Re-insert the leg assembly into the Cabinet frame and rmly attach with bolt #15 and washer #17.
• Cabinet Base B - Attach one half of the center support plate #10 to the bottom of Cabinet Base B Cabinet oor
with bolt #21 and washer #30. Insert the end and center leg assemblies into the Cabinet frame and check the leg
bracket hole alignment to make sure they are in proper alignment with the pre-installed inserts located on the inside
wall of the Cabinet. Remove the leg assemblies from the Cabinet frame and adjust the leg bracket as needed, rmly
tighten the #18 leg brackets into position. Re-insert the leg assemblies into the Cabinet frame and rmly attach with
bolt #15 and washer #17.
• Attach the leg levelers #19 to the leg assemblies by threading the leveler into the pre-installed insert located on the
bottom of the #8 leg bases.
ROCKFORD 12' TWO PIECE SHUFFLEBOARD TABLE ASSEMBLY INSTRUCTIONS
STEP 2
• Cabinet Base A - Align the pre-drilled holes in the side table frames #2 and #3 with the pre-installed inserts
located on the inside wall of the Cabinet Base #1. Attach the side table frame #2 and #3 to the Cabinet Base #1 with
bolt #20 and washer #30 as shown in the diagram below.
Note: DO NOT fully tighten the bolts at this time, the side table frame #2 and side table frame #3 ends must be
positioned so they are ush with the end of the Cabinet half at the centerline; this will allow the two Cabinet halves
to properly connect at the centerline. Once the side table frames are ush with the end of the Cabinet half at the
centerline - you can fully tighten the side table frames in place.
• Cabinet Base A - Align the pre-installed block with hole located on the end table frame #4 with the pre-installed
inserts located on the side table frames #2 and #3. Attach the end table frame with bolt #20 and washer #30.
Attach the end table frame #4 to the Cabinet bed with screw #11.
• Cabinet Base A - Align the pre-installed block with hole on the cross-support brace #9 with the pre installed
insert located on the side table frames #2 and #3. Attach the cross-support brace #9 with bolt #20 and washer #30.
Attach the cross-support brace #9 to the Cabinet bed with screw #11.
Repeat this process for Cabinet Base B.
#4
#4
#3
#1 #2
#20
#20
#30
#30
#2
#20
#30
#3
#11
Cabinet Base A Cabinet Base B
Threaded connecters
facing down
Threaded connecters
facing up
Cabinet Base B
#19
#19
#15
#17
#19
Cabinet Base A Cabinet Base B
#21
#30
#10
Note: To identify Cabinet Base A and Cabinet Base B, reference the threaded connectors in the center of each Cabinet
where the two halves join (4 threaded connectors on each Cabinet). Cabinet Base A will have the threaded connectors
facing up towards the bed of the Cabinet, while Cabinet Base B will have the threaded connectors facing down. If the
Cabinets are not identied properly prior to the following steps, part #10 in Step 3 will not install properly.

6
ROCKFORD 12' TWO PIECE SHUFFLEBOARD TABLE ASSEMBLY INSTRUCTIONS
#36
#32
#38
#37
#34
#15
#17
#38
#37
Cabinet Base B
Cabinet Base A
#30
#21
• Rotate the Cabinet Base B section with the center leg attached to the upright position.
• Slide the metal frame center trim piece #32 onto the Cabinet B wall on both sides.
• Insert the 4 brass tenons #34 into the pre-drilled holes located at the center end of Cabinet B.
• Rotate the Cabinet Base A section to the upright position, align and insert the 4 brass tenons #34 into the
pre-drilled holes located at the center end of the table frame.
• Attach the center leg assembly to the opposite half of the Cabinet A with bolt #15 and washer #17.
• Attach the other half of the center support plate #10 to the bottom of the Cabinet oor with bolt #21 and
washer #30.
Note: Please make sure that you apply inward pressure to the two halves of the table frame to ensure they
are fused tightly together before nal tightening.
* Peel back the pressure-sensitive adhesive-backed carpet on
the side Cabinet wall, located at the center connecting
position. Connect the 2 side Cabinet walls with
rod (#36), washer (#37) and nut (#38). Firmly
press the carpet back into position on
the side Cabinet wall.
STEP 4
DO NOT LEAN THE
TABLE ON ITS LEGS!
HOLD TABLE CORNER CABINET DO NOT HOLD THE LEGS
Firmly grasp the
Cabinet base table
at each corner area
Carefully rotate the Cabinet
base table to the upright
position by grasping
Cabinet table top
Position the table Cabinet in its desired
location and level the table to the oor by
adjusting the leg levelers

7
ROCKFORD 12' TWO PIECE SHUFFLEBOARD TABLE ASSEMBLY INSTRUCTIONS
STEP 5
Note: We recommend that you use a clean, level area for the assembly of the play surface. You may want
to consider utilizing the corrugated box that the table is packed in for the bottom of your work surface.
• Position the top of the play surface facing down with the recessed hardware cutouts facing the center of the
surface. All of the surface assembly will take place on the back side of the play surface.
• Make sure the surface is level prior to inserting connecting rod #27, washer #28 and nut #29 into the recessed
hardware cutouts located on the backside of the play surface #5. Firmly tighten the connecting rods in place to
fuse the two surface halves together.
• Insert the metal plate #26 into recessed hardware cutouts located on the backside of the play surface.
• Insert the metal plate #25 into the recessed hardware cutout on top of the metal plate #26 - anchor the metal
plates to the table surface utilizing bolt #23 and washer #30, these bolts must be installed in the two end holes of
the metal plate #25 at both ends.
• Install adjustment bolt #24 to the center holes on the metal plate #25, these bolts are designed to allow surface
adjustment between the two halves, by tightening or loosening the bolt #24 you can achieve a solid and ush
connection between the two play surface halves.
• Align the #31 climate adjusters to pre-drilled holes on the bottom side of the play surface, anchor in place with lag
bolt #22.
#5 #23
#24
#27#28
#29
#30
#25
#26
#22
#31

8
ROCKFORD 12' TWO PIECE SHUFFLEBOARD TABLE ASSEMBLY INSTRUCTIONS
STEP 6
Note: Make sure the Cabinet is level before inserting playing surface into the table Cabinet.
• Adjust the metal frame center trim piece #32 to the center of the frame wall to cover the seam between the two
Cabinet halves. Attach with screw #33.
• Rotate the play surface to the upright position and insert the surface into the table Cabinet.
Caution: The table play surface is very heavy and awkward -
we recommend that four strong adults rotate and
position the surface onto the table.
1
2
3
1
2
3
#4
#33
#32
STEP 7
• Align the #13 wooden slide scorers with the pre-drilled holes on the left side Cabinet frame walls, towards the end
of the table frame, install with screw #11.
• Insert #12 wood plugs into the slide scorer post to cover screws.
1
2
3
1
2
3
#13
#11 #12

9
ROCKFORD 12' TWO PIECE SHUFFLEBOARD TABLE ASSEMBLY INSTRUCTIONS
LEVELING THE CABINET
• Position the table Cabinet in the nal room location it will be set up and played on; once it’s in the desired
location, level the table Cabinet to the oor, use a simple bullet level and level the table Cabinet side to side.
• The next step is to install the play surface into the Cabinet, you may notice a gap between the end of the play
surface and the Cabinet carpet; if so, adjust the end leg levelers to raise the Cabinet up until the play surface sits
at on the carpet.
GAME PLAY PREPARATION
• Before a shueboard surface can be waxed, it should be thoroughly cleaned. To properly clean the surface, use a
soft towel and a mild glass cleaner, the goal is to remove all dirt and debris from the surface.
Optional: For added play surface longevity, we recommend coating the surface with a silicone spray that is
specically formulated for shueboard surfaces once the surface has been cleaned. This will ensure the silicone
coating you are using will not damage the nish on your play surface. The silicone spray typically dries in minutes,
any excess can be gently removed by using a soft cloth.
• The next step is to apply a light coat of wax to the play surface. Shueboard wax is really not a wax at all, it is a
mix of granular silicone and cornmeal beads that are evenly spread over the entire play surface to guarantee the
pucks will slide smoothly.
ADJUSTING THE PLAY SURFACE FOR GAME PLAY
• The next step is to adjust the play surface for optimum table play. Shueboard table surfaces are typically
adjusted to have a slight downward bow in the center known as concave, this prevents the pucks from falling o
the sides of the play surface and into the gutter during game play.
• You can test the amount of concave your play surface has by taking a straight edge box level and laying it at
across the play surface. If you can comfortably slide a piece of paper beneath the middle of the straight edge on
the play surface, your shueboard table has the correct amount of concave. If you cannot slide a piece of paper
beneath the straight edge you will need to use the climate adjusters to adjust the play surface.
• The climate adjusters are located on the bottom side of the play surface, these adjusters are made from heavy
duty steel and generally positioned three feet apart depending on the table size. The climate adjusters make
adjusting the play surface fairly simple. Each bracket has nuts on the inside and nuts on the outside. Tightening or
loosening the nuts on the climate adjusters is what allows you to adjust the play surface.
• To adjust the level of concave on your table play surface, rst loosen the inside nut all the way on both sides. Next,
tighten the outside nut using two turns. Do the exact same thing to the other outside nut. Repeat the process and
allow a few days in between before rechecking the surface to see if more adjustment is needed.
Note: In the event that your play surface is convex (bows upward), you would do the exact opposite. First
loosen the outside nut all the way on both sides. Slowly tighten the inside nut using two turns and repeat it
on the other side.
• Since shueboard tables are made out of wood, the playeld will expand and contract depending on surrounding
temperature/weather conditions. Climate adjusters allow you to maintain optimum table play by adjusting the
surface as needed. To maintain optimum table play it is recommended that you periodically check to make sure
your table is level, and the concave is correct, especially if there have been signicant temperature or humidity
changes in the room that the table is in.

10
5-YEAR LIMITED WARRANTY
This product is warranted to the original purchaser to be free from defects in material
or workmanship for a period of 5-Years from the date of the original retail purchase.
This warranty does not cover defects or damage due to improper installation,
alteration, accident, or any other event beyond the control of the manufacturer. Defect
or damage resulting from misuse, abuse, or negligence will void this warranty. This
warranty does not cover scratching or damage that may result from normal usage.
This product is not intended for institutional or commercial use: the manufacturer
does not assume any liability for such use. Institutional or commercial use will void this
warranty.
This warranty is nontransferable and is expressly limited to the repair or replacement
of the defective product. During the warranty period, the manufacturer shall repair or
replace defective parts at no cost to the purchaser. Shipping charges and insurance
are not covered and are the responsibility of the purchaser. Labor charges and related
expenses for removal, installation or replacement of the product, or components are
not covered under this warranty.
The manufacturer reserves the right to make substitutions to warranty claims if parts
are unavailable or obsolete.
The manufacturer shall not be liable for loss of use of the product, or other
consequential or incidental costs, expenses or damage incurred by the consumer of
any other use.
All warranty claims must be made to Freetime Fun. A purchase receipt with purchase
date will be required to process all warranty claims. The model number and part
numbers found within the assembly instructions will be required when submitting any
parts requests or warranty claims.
BE SURE TO CHECK OUR WEBSITE AT FREETIMEFUN.COM
FOR GREAT NEW GAMES, SAUNAS, PATIO, AND POOL SUPPLIES FOR YOUR HOME AND FAMILY!
WWW.FREETIMEFUN.COM
1830 E. FABYAN PKWY, BATAVIA, IL 60510
PHONE: [phone]
EMAIL: [email protected]
TO ORDER REPLACEMENT PARTS
VISIT OUR WEBSITE
WWW.FREETIMEFUN.COM
BEST IN GAMES, SAUNAS,
POOL AND PATIO