Fujitsu Dyna mo User manual

USB User’s Guide

Fujitsu and the Fujitsu logo are registered trademarks of Fujitsu Limited.

DynaMO is a registered trademark of Fujitsu Computer Products of America, Inc.

All other trademarks herein are the property of their respective owners.

Getting Started

For SCSI operation, refer to the SCSI User's Guide on the

DynaMO CD.

Precision. We’ve designed the DynaMO SF+USB for precision

and durability — ideal for backing up and securing your most

critical work.

Compatibility. The DynaMO SF+USB is fully compatible with

128-, 230-, 540- and 640-megabyte MO disks. In addition, you

can use Direct OverWrite (OW) disks, which enable even faster

data processing.

Minimum System Requirements.

■Intel Pentium processor or equivalent and 16MB memory

■USB version 1.1

■Windows 98 or higher; Windows 2000

Mac

■Any USB enabled Macintosh with USB version 1.1 or 1.1

upgrade

■OS 8.6 or higher

Support. Before using your DynaMO SF+USB, check that all the

components in the packing list are included in the box. If any

components are missing, please contact the place of purchase.

This guide will help you set-up and use your DynaMO drive

successfully. If you need further assistance, call our customer

service center at 1-800-626-4686.

Installing your DynaMO Software

1 Insert the DynaMO CD into your CD-ROM drive and

double click on the CD-ROM icon.

2 Double click on “setup.exe”.

3 Follow the instructions to install your software.

4 Remove the CD.

Mac

1 Insert the Disk Drive Tune Up CD into your CD-ROM drive.

2 Double click on “Disk Drive Tune Up SE Installer”.

3 Follow the instructions to install your software.

4 Remove the CD.

DynaMO Companion Software CD

The DynaMO Companion Software CD contains a variety of

useful applications to further enhance your DynaMO experience.

You are responsible for the installation, management and

operation of these applications. Fujitsu Computer Products of

America makes no representations or warranties for the software

included on the CD. All warranties, representations or support are

provided by third parties and are described in the end user license

agreement(s) included on the CD.

Install the DynaMO software before connecting hardware.

DynaMO CD

CONNECTING HARDWARE 2

Connecting your DynaMO Hardware

4 Plug the USB cable into your computer.

Your DynaMO SF+USB is now ready to use.

1 Connect USB cable to either port on your DynaMO drive.

2 Connect AC adapter

AC ADAPTER

POWER ON SWITCH

POWER ON

INDICATOR

POWER ON

SWITCH

3 Power on the DynaMO drive

Removable disks are formatted differently for different operating

systems. The MO disk included in this package is not formatted.

You must format the MO disk before using.

3 FORMATTING MO DISKS

Formatting your MO Disks

Warning: Formatting, reformatting, or changing partitions on an MO disk

will erase all data on the disk. Back up data if necessary before

proceeding.

1 Insert an MO disk into the DynaMO drive.

2 From “My Computer”, right click the removable disk icon

and select “format”.

3 Format the MO disk.

4 When formatting is complete, the MO disk is ready to use.

Mac

1 Insert an MO disk into the DynaMO drive.

2 Initialize the disk.

3 Double click on “Disk Drive Tune Up SE” icon.

4 Ensure that the USB bus is selected.

5 Select the Fujitsu drive from the numerical list of USB

devices.

6 Select partition options, if desired, or use default options and

click “install”.

7 When formatting is complete, the MO disk is ready to use.

For optimum portability and usage of your DynaMO drive and disks, it is

recommended to use the Disk Driver Tune Up drivers provided.

USING DYNAMO 4

Using your MO Disks

Inserting an MO Disk

Gently insert the MO disk with the label side up, as shown

above, until the disk clicks into place. Never force the disk into

the drive or insert the MO disk upside down as this may damage

Ejecting an MO

Emergency Eject

If the MO disk cannot be ejected as described above, or appears to

be jammed in the drive, the disk can be ejected using Emergency

Eject.

1 Turn off the DynaMO drive.

2 Straighten one end of a large paper clip.

3 Insert the straightened end of the paper clip into the hole just

below the shutter door, and push gently but firmly until the

MO disk is ejected.

Warning: Never transport your DynaMO with a disk inside. Eject the

MO disk before disconnecting the DynaMO from your system. Never

eject an MO disk while the busy indicator light is on. Damage to, or

loss of, data may result.

PC User Click the removable disk

icon with the right mouse

button and select “Eject”

from the pull-down menu.

Press the eject button of

the DynaMO drive.

Drag and drop the MO disk

icon into the trash can.

Mac User

EJECT FROM SOFTWARE MANUAL EJECT

EJECT BUTTON/

EMERGENCY EJECT

BUSY INDICATOR

5 USING DYNAMO

WRITE PROTECT

RITE ENABLE

Write protection

Your MO disk has Write Protect capability. Enabling the write

protection on the MO disk prevents data from being lost or

altered accidentally. Move switch up for Write Enable or down for

Write Protect.

Cleaning the MO disk

In normal office environments, cleaning the MO disk is not

required. In some cases, however, dust may build up on the

surface of the disk and cleaning may be required. Please contact

your place of purchase for information on the MO disk cleaning

kit.

Cleaning your DynaMO SF+USB drive

In normal office environments, cleaning your DynaMO drive is

not required. In some cases, however, dust may build up on the

objective lens of the drive and cleaning may be necessary. To clean

the objective lens you will need an optical lens cleaning kit (part

number CA90002-C980). Please contact your place of purchase

for information on where to purchase a lens cleaning kit.

Use care when handling your MO disk as dirt, fingerprints, and

moisture may degrade the disk performance.

USING DYNAMO 6

DIP Switch Settings

The DIP switch settings on your DynaMO are the recommended

settings for the USB configuration.

DP1 – Device type mode (Default Setting:off)

This switch configures the DynaMO as either an optical storage

device or a removable hard disk drive device.

DP2 – Automatic spindle stop mode (Default Setting: on)

When this setting is on, the drive automatically stops the disk to

save power when not in use.

DP3 – Write cache mode (Default Setting: on)

The DynaMO has 2 MB internal cache. Best write performance

can be achieved by the default setting (on). If you use your

DynaMO drive in harsh areas, or areas with large amounts of

dust, this switch can be set to (off).

DP4 – SCSI Terminator mode (Default Setting: on)

For USB, this switch should always be on.

For Windows® 2000, you must set the SCSI ID setting to zero.

Dos and Don’ts

■ Never turn your DynaMO over while in use.

■ Always ensure that the busy indicator light is off before turning

the power off.

■ Remove the MO disk before transporting your DynaMO.

■ Never force a disk into the drive or insert an MO disk upside

down as this may damage the drive.

■ Since a floppy disk is about the same size as an MO disk, be

careful to never insert a floppy disk into the DynaMO drive.

■ Use only ISO-compliant or GIGAMO 3.5-inch MO disks.

■ Do not use your DynaMO in areas where dust, dirt, extreme

temperatures or moisture is present.

■ Do not connect any additional devices to the DynaMO drive.

■ Never connect or disconnect the USB cable from the back of

the DynaMO while the drive power is on.

DIP SWITCH

SETTINGS 1

SCSI ID SETTING

Q & A

Q Can I create multiple partitions on an MO disk?

A PC

No. Windows 98 will allow only one partition on an MO disk.

Mac

Yes. Disk Drive Tune Up SE allows up to 15 partitions on a single

disk. See the electronic Disk Drive Tune Up SE manual for details.

Q Can I use my DynaMO SF+USB with Windows 95 OSR2.1?

A While the DynaMO drive may function using Windows 95

OSR2.1, you may encounter problems and not achieve optimum

performance.

Q Can I use my DynaMO SF+USB with my Mac running OS 8.5?

A While the DynaMO drive may function using OS 8.5, you may

encounter problems and not achieve optimum performance. We

recommend that you upgrade to OS 8.6.

Q Is the DynaMO SF+USB hot-pluggable?

A Yes. You may plug the DynaMO in at any time without having to

reboot your system. Be sure to hot-plug at the USB port on your

computer only and not from the back of the DynaMO.

Q Is the DynaMO SF+USB hot-unpluggable?

A Yes, but make sure to eject your MO disk from the DynaMO

before unplugging the drive.

Q If I power off and on my DynaMO while it’s connected to my

computer, will the system still recognize the drive?

A PC

Yes. However some PCs will not recognize the drive unless a disk

is inserted. If you encounter this, insert an MO disk and power

the DynaMO off then on again.

Mac

Yes.

Q Can I connect my DynaMO to a USB hub?

A We recommend that you connect the DynaMO SF+USB to a

USB port on your computer only.

PRODUCT TYPE Optical Disk Drive

MODEL NUMBER MDG3130SS, MDG3064SS

This device complies with part 15 of the FCC rules. Operation is subject to the following two

conditions: 1) This device may not cause harmful interference, and 2) this device must accept

any interference received, including interference that may cause undesired operation.

RESPONSIBLE PARTY

NAME Fujitsu Computer Products of America, Inc.

ADDRESS 2904 Orchard Parkway, San Jose, CA 95134-2009

Telephone: (408) 432-6333

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the

FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This

equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the

instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not

occur in a par

ticular installation. If this e

ment does cause ha

l in

vision rece

tion

whi

determined by tur

nin

the equipment off and on

to co

followin

measures: 1)Reorient or relocate the receivin

antenna

dealer or an experienced radio

TV technician for help

Technical Specifications

This pr

ct is a class 1 laser

product

to EN 6082

/IEC 82

.Th

label sho

wn to the ri

ht is affixe

the product.

USING DYNAMO 8

FCC Declaration of

ass

1 L

ase

128MB 230MB 540MB 640MB 1.3GB

90mm 3.5"MO

ISO 10090 ISO 13963 ISO 15041 ISO 15041 Gigamo

USB

1.1 MB/s 1.3-2.1 MB/s 2.3-3.9MB/s 3.4-5.9.MB/s

12 Mbits/s

23ms (typ.)

8.3ms

3,600rpm/4300rpm 3000rpm

2MB

100-120VAC.60Hz

45mm x 126mm x 215mm

4.9W 5.3W

1.5W

5 – 35∞C

0 – 50∞C

max. 3000m

10 – 85%

ata

ate

Disk capacity

Disk format

verage latency time

Rotational s

Buffer

Input power

Dimensions

Power

requirements

Temperature

Altitude operating

Humidity

Acoustics

non-operating

operating

idle

operating

Driv

23dBA

CG00000-659402

FUJITSU COMPUTER

PRODUCTS OF AMERICA, INC.

2904 Orchard Parkway

San Jose, CA 95134-2009

(800) 626-4686

(408) 432-6333

http://www.fcpa.com

email: [email protected]

Table of contents

Fujitsu DYNA MO User manual