Gecko GPW-6 User manual

E&OE ©2017 Gecko
Portable Washing Machine GPW-6
User Manual
[Revision 5.0 April 2017]
READ THIS MANUAL CAREFULLY BEFORE USE – FAILURE TO DO SO MAY RESULT IN INJURY, PROPERTY
DAMAGE AND MAY VOID WARRANTY. • KEEP THIS MANUAL FOR FUTURE REFERENCE. • Products covered by
this manual may vary in appearance, assembly, inclusions, specifications, description and packaging.

Portable Washing Machine GPW-6
E&OE ©2017 Gecko 2
Safety
•Electric shock/electrocution hazard - NEVER immerse the electrical cord or appliance in water, or
allow water to enter the electric motor compartment.
•When handling the electrical cord or plug, ensure that your hands are dry.
•If the supply cord is damaged, it must immediately be replaced by the manufacturer, its service agent
or a qualified technician.
•Do not place hands in the wash or spin dry tubs when the appliance is in use.
•Allow the washing machine at least 45 minutes between uses for the motor to cool down sufficiently.
Failure to do so may cause the thermal overload protection to trip.
•To avoid plastic deformation, do not place heavy goods or hot objects on the washing machine.
•Do not use excessive amounts of detergent, as this will affect washing.
•Water must never exceed 55°C.
•This appliance is not intended for use by persons (including children) with reduced physical, sensory
or mental capabilities, or lack of experience and knowledge. All users should have adequate training in
safely operating the product or be under supervision of a person responsible for their safety.
•Keep the washing machine away from direct sunlight and sources of heat, fire etc.
•Do not over-fill the tub as an overflow may result.
•Clothing with colours that run should be washed separately.
•For woollen garments, use a washing net bag and wash the garments inside-out.

Portable Washing Machine GPW-6
E&OE ©2017 Gecko 3
Table of Contents
Safety...................................................................................................................................................2
Parts Identification.............................................................................................................................4
Operation ............................................................................................................................................5
Washing.....................................................................................................................................................5
Rinsing.......................................................................................................................................................5
Spin-Drying................................................................................................................................................5
Lint Filter....................................................................................................................................................6
Maintenance .......................................................................................................................................7
Troubleshooting.................................................................................................................................7
Specifications.....................................................................................................................................7

Portable Washing Machine GPW-6
E&OE ©2017 Gecko 4
Parts Identification
No. Name No. Name
1 Appliance Body 9 Spin Timer
2 Wash Tub Cover 10 Lint Filter
3 Spin Tub Cover 11 Inlet Hose
4 Wash Tub 12 Outlet Hose
5 Spin Tub 13 Water Inlet Connection – Wash Tub
6 Spin Tub Secondary Cover 14 Water Inlet Connection – Spin Tub
7 Wash Timer 15 Spin Basket Cover
8 Program Selector
1
5
2
4
6
7
8
3
9 10
14
13
12
15
11

Portable Washing Machine GPW-6
E&OE ©2017 Gecko 5
Operation
Allow the washing machine at least 45 minutes between uses for the motor to cool down
sufficiently. Failure to do so may cause the thermal overload protection to trip.
Washing
1. Place the washing machine on a level surface near a drainage point.
2. Hook the top of the outlet hose tube to the top left-hand side of the machine –
this is the non-drain position.
3. Open the wash tub cover and place the clothing into the machine. Distribute
clothing evenly around the tub to prevent imbalance.
4. Connect one end of the water inlet hose to a suitable water source – the end of
the hose can be connected to a garden hose connector, and the other end to
the wash tub water inlet connection (left side). Turn on the water supply and fill
the tub until the clothes are fully immersed. Ensure that the water temperature does not exceed 40°C for
non-wool fabrics, and does not exceed 30°C for woollens. You can also fill the tub directly using a bucket
etc.
5. Add sufficient detergent for the size of the wash. Do not use any more than
necessary. Close the wash tub cover (both wash and spin tub covers must
be closed for the appliance to function).
6. Rotate (to the right/clockwise) the Wash Timer to the desired time setting.
7. Connect the appliance to a suitable electrical supply.
8. Place the Wash Program selector in the required position to start the
machine – use Soft for woollens and delicate fabrics, use Normal for
other types of general clothing.
9. When the wash has finished, unhook the outlet hose and lower it to
ground level – this is the drain position. Place the Wash Program
selector in the Drain position. Drain the water into a suitable container.
Rinsing
1. Hook the top of the outlet hose to the top left-hand side of the machine.
2. Turn on the water supply and fill the tub until the clothes are fully immersed. Ensure that the water
temperature does not exceed 40°C for non-wool fabrics, and does not exceed 30°C for woollens. You
can also fill the tub directly using a bucket etc.
3. Rotate (to the right/clockwise) the Wash Timer to the desired time setting.
4. Rotate the Program Selector to the Wash position to start the machine.
5. When the cycle has finished, drain the water.
Repeat the above processes, if necessary.
Spin-Drying
Note: The spin tub has a smaller capacity than the wash tub, so the entire wash may have to be spun in
several stages.
1. Ensure the outlet hose is at ground level.
2. Open the wash and spin tub covers, including the secondary spin tub cover. Remove the spin basket
cover from the tub.

Portable Washing Machine GPW-6
E&OE ©2017 Gecko 6
3. Transfer the clothes from the wash tub to the spin tub. Place the basket cover on top of the clothes and
press it down so it clips under the top edges of the spin tub.
4. Close the spin tub secondary cover and the wash and spin tub covers.
5. Connect one end of the water inlet hose to a suitable water source and the
other end the spin tub water inlet connection (right side).
6. Rotate (to the right/clockwise) the Spin Timer to the desired time setting –
the spin tub starts rotating.
7. Turn on the water supply for 20 to 30 seconds for a secondary rinse, then
turn the water supply off.
8. When the cycle has finished, drain the water.
Repeat the above processes, if necessary.
Lint Filter
The appliance features a filter to catch fabric lint and other small objects during the wash. The filter helps
keep washed clothes looking better and aids in preventing blockages in the appliance. Clean the lint filter
regularly. To clean the lint filter:
1. Ensure the appliance is disconnected from the electrical supply.
2. Open the wash tub cover.
3. Slide the lint filter up and out of the tub.
4. Remove any "fluff" etc from the filter netting, then rinse.
5. Re-install the lint filter.

Portable Washing Machine GPW-6
E&OE ©2017 Gecko 7
Maintenance
•Clean the machine with a soft, damp cloth, then wipe dry. Use mild detergent only if necessary.
•Store the washing machine in a cool, dry place out of direct sunlight or excessive heat.
Troubleshooting
Some procedures listed here may need to be performed by a service centre or qualified technician. • If
problems persist after following all suggested actions, contact a service centre or qualified technician.
Problem Possible Reasons and Solutions
Machine will not start. Power failure, or not connected to a suitable electrical supply.
Covers not closed.
Thermal overload protection tripped – allow machine to cool
for at least 45 minutes.
Not connected to the electric socket properly.
Timer set to "0" (zero).
Wash program selector set to DRAIN.
Machine will not drain. Outlet hose in non-drain position.
Outlet hose twisted or kinked or has a blockage.
Water in outlet hose may be frozen.
Wash or spin tub not operating at
normal speeds.
Over-filled with clothes – reduce load size.
Clothing may be caught under agitator or clumping.
Drive belt may be loose – tighten.
Spin tub motor drive shaft bolts may be loose or missing –
tighten or replace as necessary.
Power supply voltage may be too low.
Specifications
Weight Approximately 12.5kg
Maximum Wash Capacity Approximately 5kg

Portable Washing Machine GPW-6
E&OE ©2017 Gecko 8
Some experts believe the incorrect or prolonged use of almost any product could cause
serious injury or death. For information that may reduce your risk of serious injury or
death, consult the points below and additionally, the information available at
www.datastreamserver.com/safety
•Consult all documentation, packaging and
product labelling before use. Note that some
products feature online documentation which
should be printed and kept with the product.
•Check product for loose / broken / damaged /
missing parts, wear or leaks (if applicable)
before each use. Never use a product with
loose / broken / damaged / missing parts, wear
or leaks (if applicable).
•Products must be inspected and serviced (if
applicable) by a qualified specialist every 6
months assuming average residential use by a
person of average weight and strength, above
average technical aptitude, on a property
matching average metropolitan specification.
Intended use outside these guidelines could
indicate the product is not suitable for intended
use or may require more regular inspection or
servicing.
•Ensure all possible users of the product have
completed an industry recognized training
course before being given access to the
product.
•The product has been supplied by a general merchandise
retailer that may not be familiar with your specific
application or your description of the application. Be sure to
attain third-party approval for your application from a
qualified specialist before use regardless of prior
assurances by the retailer or its representatives.
•This product is not intended for use where fail-safe
operation is required. As with any product (take an
automobile, aircraft, computer or ball point pen for
example), there is always a small chance of technical
issues that needs to be repaired or may require
replacement of the product or a part. If the possibility of
such failure and the associated time it takes to rectify could
in any situation inconvenience the user, business or
employee then the product is not suitable for your
requirements. This product is not for use where incorrect
operation or a failure of any kind, including but not limited
to a condition requiring product return, replacement,
service by a technician or replacement of parts could cause
a financial loss, loss of employee time or an inconvenience
requiring compensation.
•If this item has been purchased in error after considering
the points above, simply contact the retailer directly for
details of their returns policy, if required.
©2017 Gecko. All rights reserved. No part of this document, including descriptive content, concepts, ideas,
diagrams or images may be reproduced or transmitted in any form or by any means, electronic or
mechanical, including photocopying, scanning or recording, or any information storage and retrieval system,
without express permission or consent from the publisher.