GeoVision GV-LPR CAM 10M EIA DC12V User manual

GV-LPR CAM V1.6
Installation Guide
© 2010 April GeoVision Inc.All rights reserved.
LPRCAMV16-A
Before attempting to connect or operate this product,
please read these instructions carefully and save this manual for future use.
GV-LPR CAM offers a selection of models that support different video formats to meet various
needs. This installation guide will take you through the functionality and use of GV-LPR CAM.
List of Models
AC Power Cable (110-125V, 10A) x 1
Power Adapter (100-240V, 12V/3A) x 1
Outdoor Mounting Bracket x 1
Models
Packing List
Model
GV-LPR CAM 10M EIA DC12V
GV-LPR CAM 10M CCIR DC12V
IR Optimal Distance
10 m / 32.80 ft
10 m / 32.80 ft
Video Format
NTSC
PAL
Specifications
Model
Sensor
Resolution
Lens Focal Length
Construction
Protection classification
Temperature
Power Supply
Power Consumption
LED Quantity
IR Distance
Illumination View Angle
Illuminator Life
1/3" B/W EXview CCD
570 TVL
5 ~ 50 mm, 10X
Robust aluminum with weatherproof sun-shield
IP 66
Operation: -20˚C ~ 50˚C / -4˚F ~ 122˚F Storage: -20˚C ~ 70˚C / -4˚F ~ 158˚F
DC 12V
15W
7 high-efficient LEDs
12 m / 39.37 ft
7 ~ 12 m / 22.96 ~ 39.37 ft (optimal)
30˚
25,000 hrs
GV-LPR CAM 10M EIA DC 12V GV-LPR CAM 10M CCIR DC 12V

Installing Camera Module
Push the sun shield forward to align with
the back of camera enclosure.
1. Slightly lift the camera module and slide it
out completely.
4.
Remove the foam.5.
2.
Pull out the camera module.
Sun Shield
Camera Enclosure Back
Camera Module
Completely slide the camera
module out
Loosen the set screws on the back of the
camera enclosure.
3. Loosen the screw cap on the right.6.
Insert the video cable through the screw
cap and the inside rubber of the cap.
7.
Rubber
Screw Cap
Attach the video cable to the BNC
connector and plug it into the “VIDEO OUT”
jack.
8.
Adjust the length of the video cable and
seal it with the waterproof tape.
9.
Tightly screw the cap.10.
Loosen the screw cap on the left, insert the
power cable through the screw cap and the
inside rubber.
11.
Remove the terminal block. Plug black and
white wires of the power cable to the
terminal block. Reinsert the terminal block
onto the camera. The white wire is required
to connect to the positive pin (+) on the
camera and the black wire to the negative
pin (-).
12.
VIDEO OUT
Jack
Adjust the length of the cable, seal it with
the waterproof tape, and then tightly screw
the cap (see Steps 9 and 10 for the
pictures).
13.

OSD Menu Options and Functions
LED Brightness Settings
Function
Manually adjust the camera lens.
Press SET to adjust the lens brightness.
Includes these options: 1/60, 1/100, 1/250,
1/500, 1/2000, 1/5000, 1/10000, 1/100000.
Press SET to manually adjust the shutter
speed.
Not available when the LENS is set at DC.
Turn off BLC function.
Press SET to configure the areas.
Press SET to adjust the sensitivity values.
Turn off AGC function.
Press SET to adjust the AGC ratio values.
Auto Tracking White Balance
Automatic White Balance
Press SET to select the mode from 1 to 4.
Press SET to adjust Red and Blue gain.
Adjust the Contrast from values 0 to 255.
Adjust the Sharpness from values 0 to 255.
Adjust CB_GAIN from values 0 to 255.
Adjust CR_GAIN from values 0 to 255.
Press SET to name the camera.
Select ON to reverse the image.
Select ON and press SET to configure
MOTION areas.
Select ON and press SET to configure
PRIVACY areas.
Adjust the gamma values to control brightness.
Higher gamma value shows darker images.
Press SET to change the language setting of
OSD menu options.
Press SET to restore to the factory defaults.
Close the OSD menu.
Main Menu
LENS
SHUTTER
BLC
(Backlight
Compensation)
AGC (Automatic
Gain Control)
WHITE BAL.
(White Balance)
ADJUST
FUNCTION
RESET
EXIT
Sub Menu
MANUAL
DC
FIXED
MANUAL
AUTO
OFF
ON BLC AREA
BLC RATIO
OFF
ON
ATW
AWB
FIXED
MANUAL
CONTRAST
SHARPNESS
CB_GAIN
CR_GAIN
CMAERA ID
MIRROR
MOTION
PRIVACY
GAMMA
LANGUAGE
-
-
Default Setting

-
1/500
-
Brightness: 70

-
-

-

-
-
-
87
10
176
176
OFF
OFF
OFF
OFF
1
English
-
-
The GV-LPR CAM models come with 7 LEDs which
you can adjust the brightness. You can push up (ON)
and down (OFF) the switches for LED brightness
settings. See the table below for 4 setting values.
Adjusting Camera Settings
Overview
Shutter Speed
6
5
4
3
7
89
No
1
2
3
4
5
6
7
8
9
Function
Auto Iris lens connector
Video out
Power Terminal (It is already connected. Follow Steps 11 to 12 in Installing Camera
Module to insert the Power Cable.)
Moves down the OSD menu.
Moves the focus rightward to select menu options.
Power LED
Moves up the OSD menu.
Enters the OSD menu option and confirms the selection
Moves the focus leftward to select menu options.
See the lists below for shutter speed settings.
1
2
165 SEC
182 SEC
183 (*) SEC
184 SEC
185 SEC
225 SEC
Distance between the object and the
camera is 550 cm (18.04 ft).
Notes:
1. The default settings are marked with (*).
2. The gray areas in the charts are not recommended for use.
145 SEC
150 SEC
155 SEC
170 SEC
180 SEC
200 SEC
Distance between the object and the
camera is 1100 cm (36.08 ft).
SW (1)
ON
ON
OFF
OFF
SW (2)
ON
OFF
ON
OFF
LED Brightness (mA)
470 (Default Setting)
300
200
100
Note: The factory default GAMMA value is set to be 1. It will be adjusted to 0.45 every time when you select
RESET. For optimal image performance, it is recommended to adjust the GAMMA value to 1.

Installing Camera Enclosure
After the installation of camera module and settings adjustment, you are now ready to install the
camera enclosure back.
1. Adjust the lens focus. 2. Lift the camera module.
Align the camera module to the camera
enclosure and slide it back.
3. Secure the camera enclosure with the
screws on both sides.
4.
Push the sun shield back.5.
9F, No. 246, Sec. 1, Neihu Rd.,
Neihu District, Taipei, Taiwan
Tel: [phone]
Fax: [phone]
[email protected]
http://www.geovision.com.tw