Gerber Technology GPS-2000 User manual

GPS-2000 Gerber Prime Switch
Figure 1
The smart switch box is a Z-WaveTM enabled wireless device fully compatible with
any Z-WaveTM enabled networks. This device is a security enabled Z-Wave Plus
product that uses encrypted Z-Wave Plus messages to communicate to other
security enabled Z-Wave Plus products. Z-WaveTM enabled devices displaying the Z-
WaveTM logo can also be used with this device regardless of the manufacturer and
this device can also be used in other manufacturer’s Z-WaveTM enabled networks.
This device must be used in conjunction with a Security Enabled Z-Wave Controller
in order to fully utilize all functions. Inclusion of this unit on other manufacturer’s
Wireless Controller menu allows remote operation of the unit and connected load.
Remote control of Dimmer/Relay modules are possible with other manufacturer’s
wireless Controller as well. GPS-2000 is designed to act as a repeater. Repeaters
will re-transmit the RF signal to ensure that the signal is received by its intended
destination by routing the signal around obstacles and radio dead spots. Its
functionality and supported command classes are identical when included as a
secure and non-secure device.
Adding to Z-WaveTM Network
In the front case there are nine touch screen buttons with LED light indicators which
are used to turn switches on and off or carry out inclusion exclusion and reset.
The table below provides an operation summary of basic Z-Wave functions. Please
refer to the instructions of your Z-WaveTM Certificated Primary Controller to access
the Set-up function and to Add/Remove/Associate Devices
1

Function escription Annotation
Add 1.Set your Z-Wave controller into
inclusion mode by following the
instructions provided by the
controller manufacturer.
2.The green LED will light⑤
on when every pressing and
light off when every releasing.
User should check LED ⑤
whether it accepted the
pressing or not.
Surround Blue LED light will
flash one time when enter
include mode.
3.If included successfully
Surround Blue LED light will
flash one time again.
2. Press the middle button (button ⑤)
three times within 2 seconds
intervals and device will enter
inclusion mode.
3. Node ID is included.
Remove 1.Put your Z-Wave controller into
exclusion mode by following the
instructions provided by the
Controller manufacturer.
2.The green LED will light⑤
on when every pressing and
light off when every releasing.
User should check LED ⑤
whether it accepted the
pressing or not.
Surround Blue LED light will
flash one time when enter
exclude mode.
2. Press the middle button (button ⑤)
three times within 2 seconds will
enter exclusion mode.
3. Node ID will get excluded.
Reset 1.Press the middle button (button ⑤) Use this procedure only in
four times and hold the button on
the 4th time for about 3~10
seconds then release button.
the event that the primary
controller looses connection.
The green LED will light on⑤
when every pressing and light
off when every releasing. User
should check LED whether⑤
it accepted the pressing or not.
Surround Blue LED will light on
at the 4th pressing and 5
seconds later light off.
If reset successfully Surround
Blue LED light will flash one
time.
2.IDs will get excluded and all
settings will be reset.
SmartStart 1. SmartStart enabled products can be
added into a Z-Wave network by
scanning the Z-Wave QR Code on
the product with a controller
providing SmartStart inclusion. No
further action is required and the
SmartStart product will be added
automatically to the closest network
within 10 minutes of being switched
on in the network vicinity.
2

2. The product has a DSK string. For
example : 44092-23875-12431-
52375-41125-14558-37629-65457
User can find QR Code and DSK
string on our product package and
product.
Association 1. The GPS-2000 is an always listening
Z-Wave device so associations
be added or removed by a controller
at any time.
Or If your controller requires to have
the GPS-2000 send a 'node infor-
mation frame' or NIF for associa-
tions pressing the middle button
(button⑤) three times within 2 sec-
onds will cause the GPS-2000 to
send its NIF.
The green LED will light on⑤
when every pressing and light
off when every releasing. User
should check LED whether⑤
it accepted the pressing or not.
2. There are 9 groups for the switch
Adding a node ID assigned by Z-Wave Controller means inclusion. Removing a node
ID assigned by Z-Wave Controller means exclusion.
Either failure or success when including/excluding the node ID can be viewed from the
Z-Wave Controller.
LE light Indication
To distinguish which module is in use you can view the LED light for identification.
State Type LE Indication
Relay
module
The LED ① or ⑦ will change color from blue to green when the
corresponding relay module 1 or 2 turns on. Conversely it will change
color from green to blue when relay module 1 or 2 turns off.
Dimmer
module
The LED ③ or ⑨ will change color from blue to green when the
corresponding dimmer module 3 or 4 turns on. Conversely it will change
color from green to blue when the corresponding dimmer module 3 or 4
turns off.
Smart
button
Whenever the smart button ②、④、 ⑥or ⑧ is triggered by one short
pressing and the related green LED will light on one time. Whenever the
smart button ②、④、 ⑥or ⑧ is triggered by two short pressing the related
green LED will light on two times. User should check the related green
LED whether it accepted the pressing or not.
Choosing a Suitable Location for Installation
1. The suitable room temperature for the Switch is between 0°C~40°C.
2. Do not place the Switch near combustible substances or any source of heat e.g.
fires radiators boiler etc.
3

3. After bringing into use the Switch case shell might become a hot this
phenomenon is normal.
Installation and Operation
1. Connect GPS-2000 into a plug near the relay/dimmer to be controlled.
2. Connect the load to the PNA26 module. Make sure the load to be controlled
doesn’t exceed 10A (Resistive Load). Please note that the loads attached to
NO.3 and NO.4 should be dimmable LED because it is controlled by dimmer
module. The wire connection please refer to Figure1 in the first page.
3. Toggle the button switch on the load to the ON position and it will show green
light.
4. To manually turn ON the module short press the ①、
③、 ⑦ or ⑨ button. The
green LED light will turn ON.
5. To manually turn OFF the module short press the ①、
③、 ⑦ or ⑨ button. The
blue LED light will turn ON and the load connected to the module will also be
turned OFF.
6. The ②、④、⑥ and ⑧ buttons are smart buttons which can send central
scene command to group 1 and Basic_Set command to group 3、5、6 or 8.
Programming
1. Controlling relay module by Z-Wave command
The relay module will respond to BASIC_SET and BINARY SWITCH_SET
commands that are encapsulated by Multi Channel Command Encapsulation
command.
1-1 BASIC_SET/SWITCH_BINARY_SET
The relay module will switch its On/Off state when controlled by the Controller.
For example :
On : [Command Class COMMAND CLASS MULTI CHANNEL MULTI CHANNEL
CMD ENCAP
Source endpoint = 0x00
Destination endpoint = 0x06 (or 0x01)
Command Class = COMMAND_CLASS_BASIC
Command = BASIC_SET
Value = 0x63]
Off : [Command Class COMMAND CLASS MULTI CHANNEL MULTI CHANNEL
CMD ENCAP
Source endpoint = 0x00
Destination endpoint = 0x06 (or 0x01)
Command Class = COMMAND_CLASS_BASIC
Command = BASIC_SET
Value = 0x00]
On : [Command Class COMMAND CLASS MULTI CHANNEL MULTI CHANNEL
CMD ENCAP
Source endpoint = 0x00
Destination endpoint = 0x06 (or 0x01)
Command Class = COMMAND_CLASS_SWITCH_BINARY
Command = SWITCH_BINARY_SET
Value = 0xFF]
4

Off : [Command Class COMMAND CLASS MULTI CHANNEL MULTI CHANNEL
CMD ENCAP
Source endpoint = 0x00
Destination endpoint = 0x06 (or 0x01)
Command Class = COMMAND_CLASS_SWITCH_BINARY
Command = SWITCH_BINARY_SET
Value = 0x00]
1-2 BASIC_GET
The Switch will report its On/Off state of the inquired endpoint to the Controller.
For example :
Basic Get Command : [Command Class COMMAND CLASS MULTI CHANNEL
MULTI CHANNEL CMD ENCAP
Source endpoint = 0x00
Destination endpoint = 0x01 (or 0x06)
Command Class = COMMAND_CLASS_BASIC
Command = BASIC_GET]
Basic Report Command : [Command Class COMMAND CLASS MULTI CHANNEL
MULTI CHANNEL CMD ENCAP
Source endpoint = 0x01 (or 0x06)
Destination endpoint = 0x00
Command Class = COMMAND_CLASS_BASIC
Command = BASIC_REPORT
Value = 0x00 or 0xFF]
2. Controlling dimmer module by Z-Wave command
The dimmer will respond to BASIC_SET and MULTILEVEL_SWITCH_SET
commands that are encapsulated by Multi Channel Command Encapsulation
command.
2-1 BASIC_SET / MULTILEVEL_SWITCH_SET
The dimmer module will change their level when it is controlled by the
Controller.
For example :
On : [Command Class COMMAND CLASS MULTI CHANNEL MULTI CHANNEL
CMD ENCAP
Source endpoint = 0x00
Destination endpoint = 0x03 (or 0x08)
Command Class = COMMAND_CLASS_BASIC
Command = BASIC_SET
Value = 0x01 ~ 0x63]
Off : [Command Class COMMAND CLASS MULTI CHANNEL MULTI CHANNEL
CMD ENCAP
Source endpoint = 0x00
Destination endpoint = 0x03 (or 0x08)
Command Class = COMMAND_CLASS_BASIC
Command = BASIC_SET
Value = 0x00]
On : [Command Class COMMAND CLASS MULTI CHANNEL MULTI CHANNEL
5

CMD ENCAP
Source endpoint = 0x00
Destination endpoint = 0x03 (or 0x08)
Command Class = COMMAND_CLASS_SWITCH_MULTILEVEL
Command = SWITCH_MULTILEVEL_SET
Value = 0x01 ~ 0x63]
Off : [Command Class COMMAND CLASS MULTI CHANNEL MULTI CHANNEL
CMD ENCAP
Source endpoint = 0x00
Destination endpoint = 0x03 (or 0x08)
Command Class = COMMAND_CLASS_SWITCH_MULTILEVEL
Command = SWITCH_MULTILEVEL_SET
Value = 0x00]
2-2 BASIC_GET
The dimmer module will report their On/Off state of the inquired endpoint to the
Controller.
For example :
Basic Get Command : [Command Class COMMAND CLASS MULTI CHANNEL
MULTI CHANNEL CMD ENCAP
Source endpoint = 0x00
Destination endpoint = 0x08 (or 0x03)
Command Class = COMMAND_CLASS_BASIC
Command = BASIC_GET]
Basic Report Command : [Command Class COMMAND CLASS MULTI CHANNEL
MULTI CHANNEL CMD ENCAP
Source endpoint = 0x08 (or 0x03)
Destination endpoint = 0x00
Command Class = COMMAND_CLASS_BASIC
Command = BASIC_REPORT
Value = 0x00 ~ 0x63]
3. Controlling root device by Z-Wave command
The root device will respond to BASIC_SET、 BINARY_SWITCH_SET by On/Off
the endpoint1. The root device will respond to MULTILEVEL_SWITCH_SET by
On/Off the endpoint3.
3-1 BASIC_SET / BINARY_SWITCH_SET
The relay module 1 (endpoint1) will switch its On/Off state when controlled by
the Controller.
For example :
On : [Command Class = COMMAND_CLASS_BASIC
Command = BASIC_SET
Value = 0x63]
Off : [Command Class = COMMAND_CLASS_BASIC
Command = BASIC_SET
Value = 0x00]
On : [Command Class = COMMAND_CLASS_SWITCH_BINARY
6

Command = SWITCH_BINARY_SET
Value = 0xFF]
Off : [Command Class = COMMAND_CLASS_SWITCH_BINARY
Command = SWITCH_BINARY_SET
Value = 0x00]
3-2 MULTILEVEL_SWITCH_SET
The dimmer module 3 (endpoint3) will change their level when it is controlled by
the Controller.
For example :
On : [Command Class = COMMAND_CLASS_SWITCH_MULTILEVEL
Command = SWITCH_MULTILEVEL_SET
Value = 0x01 ~ 0x63]
Off : [Command Class = COMMAND_CLASS_SWITCH_MULTILEVEL
Command = SWITCH_MULTILEVEL_SET
Value = 0x00]
Z-Wave’s Groups (Association Command Class Version 2)
The Switch can be set to send reports to control associated Z-Wave devices. It
supports 9 association groups in which every group has two support nodes.
Group1 is Lifeline support DEVICE_RESET_LOCALLY_NOTIFICATION and
CENTRAL_SCENE_NOTIFICATION.
Group2 and Group7 which correspond to relay modules 1 and 2 support
COMMAND_CLASS_SWITCH_BINARY. The relay modules 1 and 2 correspond to
endpoints 1 and 6. The device type of endpoints 1 and 6 is POWER SWITCH
BINARY.
Group4 and Group9 which correspond to dimmer module 3 and 4 support
COMMAND_CLASS_SWITCH_MULTILEVEL. The dimmer modules 3 and 4
correspond to endpoints 3 and 8. The device type of endpoints 3 and 8 is POWER
SWITCH MULTILEVEL.
Group3、5、6、8 which correspond to smart buttons ②、④、⑥、⑧ support
COMMAND_CLASS_CENTRAL_SCENE. The smart buttons ②、④、⑥、⑧
correspond to endpoints 2、 4、 5、 7. The device type of endpoints 1 and 6 are BASIC
WALL CONTROLLER.
Mapping to Association groups on the root device
Root device Endpoint 1 Endpoint 2 Endpoint 3 Endpoint 4
Group1 :
Lifeline
Group1 :
Lifeline
Group1 :
Lifeline
Group1 :
Lifeline
Group1 :
Lifeline
Group2 :
Switch_Binary_
Set from
Endpoint 1
Group2 :
Switch_Binary_
Set
Group2 :
Basic_Set
Group2 :
Switch_Multilev
el_Set
Group2 :
Basic_Set
Group3 :
7

Basic_Set from
Endpoint 2
Group4 :
Switch_Multilev
el_Set from
Endpoint 3
Group5 :
Basic_Set from
Endpoint 4
Group6 :
Basic_Set from
Endpoint 5
Group7 :
Switch_Binary_
Set from
Endpoint 6
Group8 :
Basic_Set from
Endpoint 7
Group9 :
Switch_Multilev
el_Set from
Endpoint 8
Endpoint 5 Endpoint 6 Endpoint 7 Endpoint 8
Group1 :
Lifeline
Group1 :
Lifeline
Group1 :
Lifeline
Group1 :
Lifeline
Group2 :
Basic_Set
Group2 :
Switch_Binary_
Set
Group2 :
Basic_Set
Group2 :
Switch_Multilev
el_Set
Multi Channel Command Class information of endpoints :
Root Device :
Device type : POWER_SWITCH_BINARY
Supported Command Classes : COMMAND_CLASS_ZWAVEPLUS_INFO
COMMAND_CLASS_SWITCH_BINARY
COMMAND_CLASS_SWITCH_MULTILEVEL
COMMAND_CLASS_ASSOCIATION
COMMAND_CLASS_MULTI_CHANNEL_ASSOCIATION
COMMAND_CLASS_ASSOCIATION_GRP_INFO
COMMAND_CLASS_TRANSPORT_SERVICE
COMMAND_CLASS_VERSION
COMMAND_CLASS_MANUFACTURER_SPECIFIC
COMMAND_CLASS_DEVICE_RESET_LOCALLY
COMMAND_CLASS_POWERLEVEL
COMMAND_CLASS_SECURITY
8

COMMAND_CLASS_SECURITY_2
COMMAND_CLASS_MULTI_CHANNEL
COMMAND_CLASS_CENTRAL_SCENE
COMMAND_CLASS_SUPERVISION
COMMAND_CLASS_FIRMWARE_UPDATE_MD
Controlled Command Classes : None
Description : When Reset function is triggered it will send DEVICE_RESET
_LOCALLY_NOTIFICATION to nodes of group 1.
Endpoint 1 :
Device type : POWER_SWITCH_BINARY
Supported Command Classes : COMMAND_CLASS_ZWAVEPLUS_INFO
COMMAND_CLASS_SWITCH_BINARY
COMMAND_CLASS_ASSOCIATION
COMMAND_CLASS_ASSOCIATION_GRP_INFO
COMMAND_CLASS_MULTI_CHANNEL_ASSOCIATION
COMMAND_CLASS_SUPERVISION
COMMAND_CLASS_SECURITY
COMMAND_CLASS_SECURITY_2
Controlled Command Classes : COMMAND_CLASS_SWITCH_BINARY
Description : When the on/off state of relay module 1 is changed it will send
SWITCH_BINARY_SET command to nodes of group 2.
Endpoint 2 :
Device type : BASIC WALL CONTROLLER
Supported Command Classes : COMMAND_CLASS_ZWAVEPLUS_INFO
COMMAND_CLASS_CENTRAL_SCENE
COMMAND_CLASS_ASSOCIATION
COMMAND_CLASS_ASSOCIATION_GRP_INFO
COMMAND_CLASS_MULTI_CHANNEL_ASSOCIATION
COMMAND_CLASS_SUPERVISION
COMMAND_CLASS_SECURITY
COMMAND_CLASS_SECURITY_2
Controlled Command Classes : COMMAND_CLASS_BASIC
Description : When one short press on smart button ②, it will turn on the nodes of
group 3 by sending Basic_Set command and send Central_Scene_Notification to
group 1 nodes. When two short presses on smart button ②, it will turn off the nodes
of group 3 by sending Basic_Set command and send Central_Scene_Notification to
group 1 nodes.
Endpoint 3 :
Device type : POWER SWITCH MULTILEVEL
Supported Command Classes : COMMAND_CLASS_ZWAVEPLUS_INFO
COMMAND_CLASS_SWITCH_MULTILEVEL
COMMAND_CLASS_ASSOCIATION
COMMAND_CLASS_ASSOCIATION_GRP_INFO
COMMAND_CLASS_MULTI_CHANNEL_ASSOCIATION
COMMAND_CLASS_SUPERVISION
COMMAND_CLASS_SECURITY
COMMAND_CLASS_SECURITY_2
Controlled Command Classes : COMMAND_CLASS_SWITCH_MULTILEVEL
Description : When the level of dimmer module 1 is changed and achieved the
desired level it will send SWITCH_MULTILEVEL_SET command to nodes of group
9

4.
Endpoint 4 :
Device type : BASIC WALL CONTROLLER
Supported Command Classes : COMMAND_CLASS_ZWAVEPLUS_INFO
COMMAND_CLASS_CENTRAL_SCENE
COMMAND_CLASS_ASSOCIATION
COMMAND_CLASS_ASSOCIATION_GRP_INFO
COMMAND_CLASS_MULTI_CHANNEL_ASSOCIATION
COMMAND_CLASS_SUPERVISION
COMMAND_CLASS_SECURITY
COMMAND_CLASS_SECURITY_2
Controlled Command Classes : COMMAND_CLASS_BASIC
Description : When one short press on smart button ④, it will turn on the nodes of
group 5 by sending Basic_Set command and send Central_Scene_Notification to
group 1 nodes. When two short presses on smart button ④, it will turn off the nodes
of group 5 by sending Basic_Set command and send Central_Scene_Notification to
group 1 nodes.
Endpoint 5 :
Device type : BASIC WALL CONTROLLER
Supported Command Classes : COMMAND_CLASS_ZWAVEPLUS_INFO
COMMAND_CLASS_CENTRAL_SCENE
COMMAND_CLASS_ASSOCIATION
COMMAND_CLASS_ASSOCIATION_GRP_INFO
COMMAND_CLASS_MULTI_CHANNEL_ASSOCIATION
COMMAND_CLASS_SUPERVISION
COMMAND_CLASS_SECURITY
COMMAND_CLASS_SECURITY_2
Controlled Command Classes : COMMAND_CLASS_BASIC
Description : When one short press on smart button ⑥, it will turn on the nodes of
group 6 by sending Basic_Set command and send Central_Scene_Notification to
group 1 nodes. When two short presses on smart button ⑥, it will turn off the nodes
of group 6 by sending Basic_Set command and send Central_Scene_Notification to
group 1 nodes.
Endpoint 6 :
Device type : POWER_SWITCH_BINARY
Supported Command Classes : COMMAND_CLASS_ZWAVEPLUS_INFO
COMMAND_CLASS_SWITCH_BINARY
COMMAND_CLASS_ASSOCIATION
COMMAND_CLASS_ASSOCIATION_GRP_INFO
COMMAND_CLASS_MULTI_CHANNEL_ASSOCIATION
COMMAND_CLASS_SUPERVISION
COMMAND_CLASS_SECURITY
COMMAND_CLASS_SECURITY_2
Controlled Command Classes : COMMAND_CLASS_SWITCH_BINARY
Description : When the on/off state of relay module 2 is changed it will send
SWITCH_BINARY_SET command to nodes of group 7.
Endpoint 7 :
Device type : BASIC WALL CONTROLLER
Supported Command Classes : COMMAND_CLASS_ZWAVEPLUS_INFO
COMMAND_CLASS_CENTRAL_SCENE
10

COMMAND_CLASS_ASSOCIATION
COMMAND_CLASS_ASSOCIATION_GRP_INFO
COMMAND_CLASS_MULTI_CHANNEL_ASSOCIATION
COMMAND_CLASS_SUPERVISION
COMMAND_CLASS_SECURITY
COMMAND_CLASS_SECURITY_2
Controlled Command Classes : COMMAND_CLASS_BASIC
Description : When one short press on smart button ⑧, it will turn on the nodes of
group 8 by sending Basic_Set command and send Central_Scene_Notification to
group 1 nodes. When two short presses on smart button ⑧, it will turn off the nodes
of group 8 by sending Basic_Set command and send Central_Scene_Notification to
group 1 nodes.
Endpoint 8 :
Device type : POWER SWITCH MULTILEVEL
Supported Command Classes : COMMAND_CLASS_ZWAVEPLUS_INFO
COMMAND_CLASS_SWITCH_MULTILEVEL
COMMAND_CLASS_ASSOCIATION
COMMAND_CLASS_ASSOCIATION_GRP_INFO
COMMAND_CLASS_MULTI_CHANNEL_ASSOCIATION
COMMAND_CLASS_SUPERVISION
COMMAND_CLASS_SECURITY
COMMAND_CLASS_SECURITY_2
Controlled Command Classes : COMMAND_CLASS_SWITCH_MULTILEVEL
Description : When the level of dimmer module 2 is changed and achieved the
desired level it will send SWITCH_MULTILEVEL_SET command to nodes of group
9.
1. Auto report to Grouping 1 (Maximum 2 Nodes)
1-1 Reset Event Report to Lifeline
When user executes the reset function by pressing button ⑤ it will send a
“DEVICE RESET LOCALLY NOTIFICATION” to the nodes of Group1.
For example :
Reset: [COMMAND CLASS DEVICE RESET LOCALLY DEVICE RESET
LOCALLY NOTIFICATION]
2. Control Grouping 2~9 (Maximum 2 Nodes)
2-1 Relay On/Off Event
When the “on” or “off” state has been changed it will send Switch Binary Set to
control the nodes of Group 2 or 7.
For example :
ON : [Command Class COMMAND CLASS MULTI CHANNEL MULTI CHANNEL
CMD ENCAP
Source endpoint = 0x01 (or 0x06)
Destination endpoint = 0x01
Command Class = COMMAND_CLASS_SWITCH_BINARY
Command = SWITCH_BINARY_SET
Value = 0xFF]
OFF : [Command Class COMMAND CLASS MULTI CHANNEL MULTI CHANNEL
CMD ENCAP
11

Source endpoint = 0x01 (or 0x06)
Destination endpoint = 0x01
Command Class = COMMAND_CLASS_SWITCH_BINARY
Command = SWITCH_BINARY_SET
Value = 0x00]
2-2 immer module On/Off Event
When the dimmer level has been changed and stop it will send Switch Multilevel
Set to control the nodes of Group 4 or 9.
For example :
ON : [Command Class COMMAND CLASS MULTI CHANNEL MULTI CHANNEL
CMD ENCAP
Source endpoint = 0x03 (or 0x08)
Destination endpoint = 0x01
Command Class = COMMAND_CLASS_SWITCH_MULTILEVEL
Command = SWITCH_MULTILEVEL_SET
Value = 0x01 ~ 0x63] (The value is the same as the stopped dimmer level.)
OFF : [Command Class COMMAND CLASS MULTI CHANNEL MULTI CHANNEL
CMD ENCAP
Source endpoint = 0x03 (or 0x08)
Destination endpoint = 0x01
Command Class = COMMAND_CLASS_SWITCH_MULTILEVEL
Command = SWITCH_MULTILEVEL_SET
Value = 0x00]
3. Pressing button control the correspondent Group (Maximum 2 Nodes)
3-1 Pressing button to switch On/Off Relay
Button① correspond to relay1 and button⑦ correspond to relay2. When the relay
is off shortly pressing the assigned button will turn it on and send Basic_Set
command to the nodes of group 2 or 7 and vice versa.
For example :
ON : [Command Class COMMAND CLASS MULTI CHANNEL MULTI CHANNEL
CMD ENCAP
Source endpoint = 0x01 (or 0x06)
Destination endpoint = 0x01 (send to correspond grouping nodes)
Command Class = COMMAND_CLASS_SWITCH_BINARY
Command = SWITCH_BINARY_SET
Value = 0xFF ]
OFF : [Command Class COMMAND CLASS MULTI CHANNEL MULTI CHANNEL
CMD ENCAP
Source endpoint = 0x01 (or 0x06)
Destination endpoint = 0x01 (send to correspond grouping nodes)
Command Class = COMMAND_CLASS_SWITCH_BINARY
Command = SWITCH_BINARY_SET
Value = 0x00]
3-2 Pressing button to control level of dimmer
Button③ correspond to dimmer module 3 and button⑨ correspond to dimmer
module 4. When if the dimmer stays at 30% shortly pressing the assigned button
will turn it off and send Switch_Multilevel_Set to the nodes of group 4 or 9. Shortly
12

pressing the same button again will turn it back to the last level (30%) and send
Switch_Multilevel_Set to the nodes of group 4 or 9. To adjust the dim level press
and hold the assigned button until the desired dim level is achieved then release.
It will send the Switch_Multilevel_Set command to the nodes of group 4 or 9.
For example :
ON :
(Shortly
pressing
button)
[Command Class COMMAND CLASS MULTI CHANNEL MULTI
CHANNEL CMD ENCAP
Source endpoint = 0x03 (or 0x08)
Destination endpoint = 0x01 (send to correspond grouping nodes)
Command Class = COMMAND_CLASS_SWITCH_MULTILEVEL
Command = SWITCH_MULTILEVEL_SET
Value = 0x01 ~ 0x63]
OFF :
(Shortly
pressing
button)
[Command Class COMMAND CLASS MULTI CHANNEL MULTI
CHANNEL CMD ENCAP
Source endpoint = 0x03 (or 0x08)
Destination endpoint = 0x01 (send to correspond grouping nodes)
Command Class = COMMAND_CLASS_SWITCH_MULTILEVEL
Command = SWITCH_MULTILEVEL_SET
Value = 0x00]
Dim :
(Release
button
after
a long
pressing
[Command Class COMMAND CLASS MULTI CHANNEL MULTI
CHANNEL CMD ENCAP
Source endpoint = 0x03 (or 0x08)
Destination endpoint = 0x01 (send to correspond grouping nodes)
Command Class = COMMAND_CLASS_SWITCH_MULTILEVEL
Command = SWITCH_MULTILEVEL_SET
) Value = 0x00 ~ 0x63]
3-3 Pressing smart button to control the corresponding grouping nodes
The smart Button②、④、⑥ and ⑧ correspond to groups 3 、5、6 and 8
respectively.
3-3-1 One short press :
One short press on a smart button ②、④、⑥or ⑧, can turn on the
nodes of group 3、5、6 or 8 by sending Basic_Set command. It will also send
Central_Scene_Notification to group 1 nodes.
For example :
[Command Class COMMAND CLASS MULTI CHANNEL MULTI CHANNEL CMD
ENCAP
Source endpoint = 0x02
Destination endpoint = 0x01 (send to correspond grouping nodes)
Command Class = COMMAND_CLASS_BASIC
Command = BASIC_SET
Value = 0xFF]
[COMMAND_CLASS_CENTRAL_SCENE CENTRAL_SCENE_NOTIFICATION
Value1 = 0x03 – Sequence number
Value2 = 0x80 – Key pressed 1 time (Slow refresh = True)
Value3 = 0x01 – Scene number]
3-3-2 Two short presses:
Two short press on a smart button②、④、⑥or ⑧, can turn off the nodes of group
13

3、5、6 or 8 by sending Basic_Set command. It will also send
Central_Scene_Notification to group 1 nodes.
For example :
[Command Class COMMAND CLASS MULTI CHANNEL MULTI CHANNEL CMD
ENCAP
Source endpoint = 0x02
Destination endpoint = 0x01 (send to correspond grouping nodes)
Command Class = COMMAND_CLASS_BASIC
Command = BASIC_SET
Value = 0x00]
[COMMAND_CLASS_CENTRAL_SCENE CENTRAL_SCENE_NOTIFICATION
Value1 = 0x03 – Sequence number
Value2 = 0x83 – Key pressed 2 time (Slow refresh = True)
Value3 = 0x01 – Scene number]
Firmware update over the air (OTA)
GPS-2000 is based on 500 series SoC and supports Firmware Update Command
Class it can receive the updated firmware image sent by controller via the Z-wave
RF media. It is a helpful and convenient way to improve a function if needed.
Command Classes
The GPS-2000 supports Command Classes including…
Command Class Version Required Security Class
Association 2 Highest granted Security Class
Association Group Information 1 Highest granted Security Class
Basic 1 Highest granted Security Class
Central Scene 3 Highest granted Security Class
Device Reset Locally 1 Highest granted Security Class
Firmware Update Meta Data 4 Highest granted Security Class
Manufacturer Specific 2 Highest granted Security Class
Multi Channel 4 Highest granted Security Class
Multi Channel Association 3 Highest granted Security Class
Powerlevel 1 Highest granted Security Class
Security 0 1 None
Security 2 1 None
Switch Binary 1 Highest granted Security Class
Switch Multilevel 1 Highest granted Security Class
Supervision 1 None
Transport Service 2 None
Version 3 Highest granted Security Class
Z-Wave Plus Info 2 None
Troubleshooting
14

Symptom Cause of Failure Recommendation
The GPS-2000 does not
work and the LED light is
off
1. The GPS-2000 is not
plugged into the
electrical outlet
properly
1.Check power connect properly
2. The Switch is broken 2. Don’t open up the Switch and send
back for repair.
The LED light is on but
cannot turn ON or OFF
GPS-2000
1. Check if the load
plugged into the Switch
has its own ON/OFF
switch
1. Toggle the ON/OFF switch of the load
to ON
2. Is not carrying out
association
2. Carry out association
3. Same frequency
interference
3.Wait for a while to re-try
Specification
Operating Voltage 100~120Vac/ 60Hz; 220~240Vac/ 50Hz
Maximum Load 10A (Resistive Load)
Range Minimum 40 m in door 100m outdoor line of sight
Operating Temperature 0°C ~ 40°C
Frequency Range 868.4MHz & 869.85MHz/ EU (GPS-2000-1)
908.4MHz & 916.0MHz/ US (GPS-2000-2)
922~927MHz/ Taiwan/ Japan (GPS-2000-3)
916MHz/Israel(GPS-2000-7)
** Specifications are subject to change and improvement without notice.
FCC I : 2AQO4GPS-2000
Warning:
1. o not exceed the max loading.
Disposal
This marking indicates that this product should not be disposed with other
household wastes throughout the EU. To prevent possible harm to the
environment or human health from uncontrolled waste disposal recycle it
responsibly to promote the sustainable reuse of material resources. To
return your used device please use the return and collection systems or
contact the retailer where the product was purchased. They can take this
product for environmental safe recycling
Company of License Holder：Gerber Technology 2016 LTD
Address of License Holder：75 Haerez St. Kfar Hanagid Israel 7687500
15

FCC Interference Statement
This equipment has been tested to comply with the limits for a Class B digital device, pursuant
to Part 15 of the FCC ules.
These limits are designed to provide reasonable protection against harmful interference in a
residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to radio commu-
nications.
However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged to try to cor-
rect the interference by one of the following measures:
• eorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
• Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC ules. Operation is subject
to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause
undesired operation.
FCC Caution: Any changes or modifications not expressly approved by the party responsible
for compliance could void the user's authority to operate this equipment.
This transmitter must not be co-located or operating in conjunction with any other antenna or
transmitter.
16