GGM gastro BD-32 User manual

UPRIGHT FREEZER
INSTRUCTION MANUAL
Model No.: BD-32
,
To ensure proper use of this appliance and your safety, please read the following instructions
completely before operating this appliance.

TABLE OF CONTENTS
Before Putting Into Use…………………………………………………………………..2
Tips For Energy Saving…………………………………………………………………..2
Important Safety Instructions…………………………………………………………….2
Correct Disposal of this product...............................................................................4
Name Of The Parts………………………………………………………………………..5
Specifications………………………………………………………………………………5
How To Operate:
Starting Your New Refrigerator…………………………………………………...6
Temperature Control……………………………………………………………… 6
How To Defrost……………………………………………………………………. 6
Level your freezer…………………………………………………………………..7
Door alignment................................................................................................7
Door Reversal Instruction……………………………………………….……..…. .7
Food storage information...................................................................................9
How To Clean……………………………………………………………………….……...10
How To Install………………………………………………………………………….…….10
Care And Maintenance…………………………………………………………………......10
Troubleshooting Guide
What To Do………………………………………………………………………......11
Refrigerator Warranty………………………………………………………………………12

BEFORE PUTTING INTO USE
Before connecting the appliance to the power supply, let the unit stand upright for 4 hours,
which will reduce the possibility of the cooling system malfunctioning due to improper handling.
Clean your unit thoroughly before putting into use. (See “How to Clean”)
Use the parts diagram on page 4 to insure proper positioning of internal components.
TIPS FOR ENERGY SAVINGS
Keep the freezer doors closed as much as possible, particularly in warm / humid conditions.
Maintain adequate ventilation around the back and sides of the unit.
Maintain a thermostat setting of “4” position under normal use.
Allow warm food to cool to room temperature before placing in the freezer.
Excessive ice build up will increase energy consumption. Defrost the unit when ice / frost is
4-5mm thick.
IMPORTANT SAFETY INSTRUCTIONS
Use this appliance only for its intended purpose as described in this owner’s manual.
This appliance is intended to be used in household and similar applications such as:
–staff kitchen areas in shops, offices and other working environments;
–farm houses and by clients in hotels, motels and other residential type environments;
–bed and breakfast type environments;
–catering and similar non-retail applications.
When using electrical appliances, basic safety precautions should be followed to reduce the risk of fire,
electric shock, and injury to persons or property. Read all instructions before using any appliance.
This appliance can be used by children aged from 8 years and above and persons with reduced
physical, sensory or mental capabilities or lack of experience and knowledge if they have been given
supervision or instruction concerning use of the appliance in a safe way and understand the hazards
involved. Children shall not play with the appliance. Cleaning and user maintenance shall not be made
by children without supervision.
This unit must be properly installed in accordance with the installation instructions before it is
used. (see “How to install”)
This unit must be positioned so that the plug is accessible.
Do not run cord over carpeting or other heat insulators. Do not cover the cord. Keep cord away from
traffic areas, and do not submerge in water. No other appliance should be plugged into the same
outlet, and be sure that the plug is fully inserted into the receptacle.
We do not recommend the use of extension cord as it may overheat and cause a risk of fire. If you
must use an extension cord, use 1.5mm2minimum size and rated no less than 1875 watts.
Disconnect the mains plug from the supply socket when not in use for a long term, where supply
connection is via mains plug.
Never unplug you unit by pulling on the power cord. Always grasp the plug firmly and pull straight out
from the outlet.
If the supply cord is damaged, it must be replaced by the manufacturer or its service agent or a
similarly qualified person in order to avoid a hazard.
1) Do not clean your unit with flammable fluids. The fumes can create a fire hazard or explosion.

2) Do not tip over the unit.
3) If the freezer is brought in from outside in wintertime, give it a few hours to warm up to room
temperature before plugging it in.
4) Repair or replace immediately all electric service cords that have become frayed or otherwise
damaged. Do not use a cord that shows cracks or abrasion damage along its length, the plug or the
connector end.
5) Unplug the unit before cleaning or making any repairs or servicing. NOTE: If for any reason this
product requires service, we strongly recommend that a certified technician perform the service.
Repairs made by non-qualified personnel will void the warranty.
6) The power supply must be properly grounded. Do not disconnect or move off the ground pin in any
case.
7) Do not use your unit outdoors. Place the unit away from direct sunlight and make sure that there is
at least 10 cm of space between the back of your unit and wall. Keep a minimum distance of 10 cm on
each side of your unit free. Keep the enough air circulation around your unit.
8) It is recommended that the unit is positioned away from any combustible sources such as gas,
petrol, alcohol, lacquer and banana oil, etc. The aforementioned objects should not be stored in the
unit under any circumstances.
WARNING: This appliance must be earthed. Use the proper main power source according to the
nameplate.
WARNING: Keep ventilation openings, in the appliance enclosure or in the built-in structure, clear of
obstruction.
WARNING: Do not use mechanical device or other means to accelerate the defrosting process, other
than those recommended by the manufacturer.
WARNING: Do not damage the refrigerant circuit.
WARNING: Do not use electrical appliances inside the food storage compartments of the appliance,
unless they are of the type recommended by the manufacturer.
WARNING: To avoid a hazard due to instability of the appliance, it must be fixed in according with the
instructions.
WARNING: Do not store explosive substances such as aerosol cans with a flammable propellant in this
appliance.
WARNING: When positioning the appliance, ensure the supply cord is not trapped or damaged.
WARNING: Do not locate multiple portable socket-outlets or portable power supplies at the rear of the
appliance
To avoid contamination of food, please respect the following instructions:
–Opening the door for long periods can cause a significant increase of the
temperature in the
compartments of the appliance.
–Clean regularly surfaces that can come in contact with food and accessible
drainage systems.
–Store raw meat and fish in suitable containers in the refrigerator, so that it is not in
contact with or
drip onto other food.
–Two-star frozen-food compartments are suitable for storing pre-frozen food, storing
or making ice-cream and making ice cubes.
–One-, two- and three-star compartments are not suitable for the freezing of fresh
food.
–If the refrigerating appliance is left empty for long periods, switch off, defrost, clean,
dry, and leave the door open to prevent mould developing within the appliance.

IMPORTANT:
The wires in this mains lead are colored in accordance with the following code:
Green or Green with a strip yellow: Grounding
Blue: Neutral
Brown: Live
During using:
1) Do not touch the cooled surfaces while the appliance operates, especially not with wet hands,
because the skin may stick to the cold surfaces.
2) Do not freeze bottled liquids such as carbonated soft drink, beer, wine, etc. Doing so can cause
glass bottles and aluminum cans to rupture.
3) If the unit fails to cool properly, dispose of spoiled food as needed.
Correct Disposal of this product
Warning: Risk of fire/flammable materials used. Please according to local
regulations regarding disposal of the appliance for its flammable blowing gas. When disposal
of any materials, must comply with your local recycling policy and environmental
protection policy. Do not release the flammable refrigerant contained in the
cooling system freely.
Before you scrap the appliance, please take off the doors to prevent children trapped.
DANGER: Risk of child entrapment. Before you throw away your old refrigerator or freezer:
Take off the doors.
Leave the shelves in place so that children may not easily climb inside.
This marking indicates that this product should not be disposed with other
household wastes throughout the EU. To prevent possible harm to the
environment or human health from uncontrolled waste disposal, recycle it
responsibly to promote the sustainable reuse of material resources. To return your
used device, please use the return and collection systems or contact the retailer
where the product was purchased. They can take this product for environmental
safe recycling.

NAME OF THE PARTS
Model No.: BD-32
⑴Wire Shelf
⑵Bottom foot
⑶Door assembly
⑷Top hinge cover
⑸Freezer Compartment
⑹Temperature Thermostat Box(not shown, located at the back)
SPECIFICATIONS
Product Description
Upright freezer
Model No.
BD-32
Capacity
32 L
Electrical Rating
220-240V~ 50Hz/0.3 A
Refrigerant
R600a, 24g
Unit Dimensions With
Feet
Width
Depth
Height
445mm
473mm
498mm
Net Weight (Lbs)
15 Kg
1
2
3
4
5
6

HOW TO OPERATE
Starting Your New Freezer
1. Clean the freezer thoroughly. Wipe the outside with a soft dry cloth, the interior with a clean
moist cloth.
2. Insert the power supply cord into the socket.
3. Turn the thermostat dial to “7”. Close the door and let the unit operate for 2-3 hours.
4. Reduce the thermostat to a mid-range setting “3”-“5” on the thermostat control.
Temperature Control
Thermostat Dial
To control the internal temperature, adjust the
thermostat dial. “1” is the warmest setting. “7” is
the coldest. To turn the unit off, turn the
temperature control knob to ‘0”. *
*Note:
Turning the temperature control to
“0” position stops the cooling cycle
but it does not shut off the power
supply to the unit.
If you need quick freezing, turn the thermostat dial to “7”position, the compressor will run always,
when the food is frozen completely, then turn the dial to the original position.
The Dial may be set any place on the scale. It does not have to be set exactly on a number.
Note: Wait 3-5 minutes before restarting if you just unplug the unit. The unit may fail to operate
properly if restarted too quickly.
How To Defrost
Defrost the freezer compartment when the ice / frost is approximately 4-5 mm thick. Set the
thermostat dial to “0” to defrost. Remove all contents from the freezer compartment. Leave the freezer
door open to allow accumulated ice / frost to melt. Remove large pieces of ice as needed. Do not
use hot water or other electric heating devices to melt the accumulated ice. After defrosting, remove
accumulated ice / water and wipe the freezer compartment dry with a soft cloth. Restart the unit per
starting instructions.
Never use a knife, or other sharp metal instrument to scrape ice/frost on the surface of the
internal wall of the unit.

Leveling Your Freezer
Door Alignment
Door Reversal Instruction
We supply you the freezer with left side open door or right side open door. Please buy the correct unit
according to your installation location. If you are not sure, or want to change the location, please
reverse the door refers to the following figure and explanation according to your new installation
location.

Your freezer is built with a reversible door. You have the choice of either opening it from the left or the
right side. In order to reserve the opening direction of your door, please follow these simple
instructions:
Remove all goods out of your freezer. Tilt the freezer backwards. Secure the rear from sliding. Tape
the door to the cabinet to prevent from falling.
Note: The above figure shows that one bottom foot is on the base bracket (normal not), you
will have to remove this foot from base bracket before beginning. And install it back to the
base bracket after you complete it.
1. Remove the 2 hexagonal screws from base bracket.
2. Remove the pivot washer holding the bottom of the door.
3. Separate the door from the cabinet and remove the pivot axle from the upper side of the door.
Remove and reinstall upper and lower axle inserts to opposite side.
4. Install the pivot axle to opposite side.
5. Re-attach the door to the cabinet and secure with tape.
6. Attach the base bracket to the opposite side.
7. Install the bottom pivot aligning with the lower pivot insert on the door. Attach the 2 hexagonal
screws to base bracket.
8. Remove tape.
9. As the unit was tilted, wait 24 hours before plugging it in.

HOW TO CLEAN
Cleaners: Never use harsh, abrasive cleaners, heavy-duty cleaners, or solvents on any surface.
Exterior: Wipe with damp, sudsy cloth, rinse and dry. For stubborn stains and for periodic waxing,
use silicon wax.
Freezer: When unit needs defrosting turn thermostat to “OFF”(“0”). Do not use sharp metallic
instruments to scrap off ice/frost.
Refrigeration Section: Wash shelves and other removable parts in warm sudsy water, rinse and dry.
Wash interior with baking soda solution (3 tablespoons to I liter of water) or warm sudsy
water, rinse and dry.
Magnetic Door Seals: Wash with warm sudsy water.
The Finishing Touch: Replace all parts and return thermostat dial to desired setting.
WARNING: Do not clean your unit with flammable fluids. The fumes can create a fire
hazard or explosion.
HOW TO INSTALL
WARNING：This unit is not designed for recessed installation.
Install freezer in a convenient location away from
extreme heat and cold. Allow sufficient clearance
between the freezer and sidewall so the door will open
without obstruction. This freezer is not designed for
recessed installation.
Select a space with strong level floor. Not
recommended for carpeting or other soft / uneven
surfaces.
Allow 10 cm of space between the unit and the
sidewall to keep good air circulation. In addition,
sufficient clearance (160°) should be maintained to
allow the door to open properly and completely.
The appliance must be correctly connected to the power supply, 220-240V~50Hz,with grounding
Do not use an extension cord.
WARNING: To avoid a hazard due to instability of the appliance, it must be placed at an even or flat
surface.
POWER CORD REPLACEMENT
If the freezer’s power cord is damaged, have it replaced by a qualified repair agent.
CARE AND MAINTENANCE
The freezer should be cleaned on a regular basis. (See: “HOW TO CLEAN”)
It is necessary to have an adequate ventilation space around the refrigerator in order to
attain proper performance, dissipation of heat, maintain efficiency, and low power consumption.
Clearance of minimum 10 centimeters should be maintained at the rear and sides of the unit and
20 cm at the top of the unit.
10cm

Do not modify the power cord under any circumstance to allow the unit to be plugged into a
non-grounded outlet. To avoid heat damage to the power cord, please ensure that it does not
come in proximity or in direct contact with the compressor of the refrigerator.
Please avoid installing the refrigerator in a location where the appliance will come in contact
with water or moisture to minimize rusting of metal parts.
The freezer should not be installed near any heat source or in a location where it will come
in direct contact with the sunlight.
TROUBLESHOOTING GUIDE
WHAT TO DO …
When the fridge is not in use for a prolonged period:
Remove the plug from the outlet.
Remove all contents from the fridge.
Dry the interior and leave the door open for a few days.
When the freezer does not work:
Check if there is a power failure
Check if the power plug is plugged into the power outlet
Check that the fuse has not blown in main supply circuit
When you wish to move the fridge:
Secure all movable parts and contents. (Package them separately if necessary.)
Transport the fridge only in an upright position. In any other position you may damage the
compressor.
Before calling service, please follow the checklist below.
This may save you an expensive service call.
If the freezer seems too warm inside:
Check to see that the door is closing properly and the door seal is not damaged.
Check that the interior circulation is not obstructed by having too many goods stored. (The
fridge is overloaded)
Did you store anything hot, without first cooling it to room temperature?
Is there sufficient clearance around all sides and above the fridge?
When the freezer is cooling excessively:
The temperature control dial may be set too high
If you place food sorts which contain a lot of moisture directly under the cool outlets, they will
freeze easily. This does not indicate a unit malfunction.
When the defrosting water overflows inside the refrigerator and onto the floor:
Check that the drain pipe and the drain hose are not clogged.
Check that the drain pan is housed properly.

When condensation forms on the outside of the refrigerator:
Condensation may form on the outside when the humidity level is high such as during a wet
season. This is the same result as the condensation formed when chilled water is poured into a
glass. It does not, therefore, indicate a failure, wipe dry with a dry cloth.
If the fridge starts making any unusual noises:
Is it wobbling? Re-level it and check if it now operates normally.
Have any objects fallen behind the fridge? If so, remove them and check if operation is now
normal.
Are any containers inside the fridge vibrating or resonating? If so, rearrange them then check to
see if operation has returned to normal.
Warranty
The manufacturer provides warranty in accordance with the legislation of the customer's own country
of residence, with a minimum of 1 year (Germany: 2 years), starting from the date on which the
appliance is sold to the end user.
The warranty only covers defects in material or workmanship.
The repairs under warranty may only be carried out by an authorized service centre. When making a
claim under the warranty, the original bill of purchase (with purchase date) must be submitted.
The warranty will not apply in cases of:
- Normal wear and tear
- Incorrect use, e.g. overloading of the appliance, use of non-approved accessories
- Use of force, damage caused by external influences
- Damage caused by non-observance of the user manual, e.g. connection to an unsuitable mains
supply or non-compliance with the installation instructions
- Partially or completely dismantled appliances