growplay CP20 - REV 2 User manual

COMPACT FRAME FREE STANDING
Assembly, Maintenance and User
Instructions Manual
WARNING!
READ ALL PRECAUTIONS AND INSTRUCTIONS IN THIS MANUAL
BEFORE USING THIS EQUPIMENT.
KEEP MANUAL IN A SAFE PLACE FOR FUTURE
TOTAL WEIGHT CAPACITY = 300KG
AGE OF USERS 3+
GROWPLAY MONKEYBARS ® PTY. LTD.
ABN: 36 627 796 141
P.O Box 2527, Clarkson, WA, 6030
Model: CP20 –REV 2
growplaymonkeybars.com/pages/assembly-installation

BEFORE YOU BEGIN
Thank you for purchasing Growplay Monkey Bars. With regular maintenance, your set will
provide many years of backyard fun.
Before you start to assemble your new GROWPLAY MONKEY BAR SET please ensure that
you have read this important information and that it is communicated to all users prior to
use.
INSTALLATION WARNING!
•Read all important precautions and instructions in this manual and all warnings on
the equipment to reduce the risk of serious injury.
•It is the responsibility of the owners and supervisors of this equipment to ensure
that it has been correctly assembled, anchored, maintained and the users obey the
safety instructions.
•This product is intended for use by children AGE OF USERS 3+
•Until the equipment has been correctly assembled and anchored, do not let children
use equipment.
•Always use Growplay Monkey Bars under adult supervision.
•It is required that the play equipment be ground anchored with the ground anchor
nails provided onto a soft or shock absorbing surface.
•Do not install over concrete or any other hard surface as a fall onto a hard surface
could result in serious injury or death.
•Ensure that the equipment is installed on a level surface and no less than 1.8 metres
from any structure or obstruction.
•Always inspect the equipment before it is used and replace any worn, defective, or
missing parts.
•Ensure that all connectors are regularly checked.
ELECTROCUTION HAZARD
Growplay monkey bars are made from metal. They are not grounded and will conduct
electricity. For obvious reasons and electrocution hazard exists. NO lights, heaters, electrical
and extension cords or any household electrical device or appliances are to be permitted on
or in the frame at any time.
WARNING: THIS DISASSEMBLED PRODUCT MAY CONTIAN SMALL PARTS
WHICH POSE A CHOKING HAZARD TO CHILDREN UNDER 3.
WARNING: ACCESSORIES MUST ONLY BE ATTACHED IN POSITIONS AS SHOWN IN
THESE INSTRUCTIONS. FAILURE MAY RESULT IN DEATH OR SERIOUS INJURY.

FOR THE USER
•Do not use this equipment when under the influence of drugs or alcohol.
•Do not jump on or off the frame.
•Wear clothing that does not have loops, hooks, drawstrings, or anything else that
can get caught on the frame.
USER INSTRUCTIONS
1. GROWPLAY MONKEY BARS are designed for up to 6 persons and not exceeding total
weight of 300kg.
2. AGE OF USERS 3+
3. Adult supervision for children of all ages is required at all times.
4. Educate children not let to walk close to, behind and in front, between moving parts.
5. Children are not to use the equipment in any other manner than intended.
6. Teach children not to hop off equipment while in motion or jump from moving play
items.
7. Do not twist chains or ropes or loop them over support bars as this may reduce the
structural integrity of the rope or chain.
8. Do not allow use of the equipment when it is wet as injury due to slips may occur.
9. Children are to be dressed in appropriate clothing while playing on or around the
equipment with correctly fitted and full foot enclosing footwear. Loose fitting items,
hood, and neck draw strings etc could potentially cause injury or death by
strangulation.
10. Inform children not to attach items to the playground equipment that are not
specifically designed or approved for use with the Growplay monkey bar equipment,
such as, but not limited to jump ropes, clothesline, pet leashes, cables, and chain as
they may cause a strangulation hazard.

ASSEMBLY: TWO PERSONS
Before starting assembly, please carefully read the following information.
•Two people are required to assemble frame.
•DO NOT FULLY TIGHTEN BOLTS UNTIL FRAME IS ASSEMBLED.
•Place all parts in one cleared area and remove the packaging material. Do not throw
away material until assembly is complete.
•Dispose of the packaging thoughtfully and ensure any plastic bags and small parts
are kept away from children or pets.
•Ensure that you check all tightening of parts twice and that the frame is stable after
assembly. Small movement through the frame is normal.
•Allow plenty of time to ensure that your monkey bars are set up correctly and safe to
use.
•Ensure that no exposed red tape is present and that all fixtures are extremely tight.
Ensure that tube is
correctly inserted and
tight! No red tab should
be seen.

LEVEL GROUND
IMPORTANT! ENSURE GROUND IS LEVEL. USE GROUND
ANCHOR SCREWS ON 4 OUTSIDE LEGS TO SECURE FRAME
BEFORE USE.
BASE PLATE
WASHER
GROUND ANCHOR

THE SAFETY BOLT IS SHOWN AS
RED IN THIS MANUAL TO
INDICATE THAT THIS SPECIAL
FASTERNER IS REQUIED TO
LOCATE POSITION OF TUBE AND
PREVENT LOOSENING
TYPICAL CHICAGO BOLT ASSEMBLY
IMPORTANT! ONLY FULLY TIGHTEN BOLTS ONCE FRAME IS
ASSEMBLED. FINGER TIGHTEN ONLY DURING ASSEMBLY.
TYPICAL RUNG ASSEMBLY
REFER TO PART NUMBERS
PRINTED ON ALL
TUBULAR PARTS DURING
ASSEMBLY.

ASSEMBLE MONKEY RUNG (MR1800KIT) S AS SHOWN

ASSEMBLE 2 x LADDER (LD2) AS SHOWN
NOTE CLAMP ON OPPISITE SIDE TO CLAMPS 11 & 12

PLACE SHORT TEE’S AS SHOWN.
FACING INWARDS WITH BOTS
UPWARDS. LEAVE LOOSE. DO NOT
TIGHTEN.
SECURE BASE PLATE
PLATE
HOLES MUST
BE FACING
INWARDS!
FRONT LEGS: IMPORTANT! LAY PARTS OUT AS SHOWN.
PART NUMBERS ARE PRINTED ON TUBULAR PARTS
CP20D1
CP20D2
CP20D2
CP20D1

CP20E1K
CP20A2
LOCATE SAFETY BOLT BOTH
SIDES FACING FORWARD
THROUGH 3 WAY CLAMP AS
SHOWN. FINGER TIGHTEN
ONLY!
CP20A2
CP20E1K
CONNECT CP20E1K WITH
BOLTS AND SLIDE ON REAR
3 WAY CLAMP. LEAVE
LOOSE UNTIL FRAME
ASSEMBLY.
NOTE END CAPS TO REAR
TOP SIDE RAILS: IMPORTANT! LAY PARTS OUT AS SHOWN.
RIGHT HAND TOP RAIL
LEFT HAND TOP RAIL
SLIDE 3 WAY TEE ONTO PART
CP20A2 FIRST AND ALIGN
WITH HOLE. INSERT SAFETY
BOLT FINGER TIGHT. NOTE
THAT THE BOLT IS
OUTWARDS WITH THE KINK
INWARDS AS SHOWN.

BOTTOM SIDE RAILS: IMPORTANT! LAY PARTS OUT AS SHOWN.
PART NUMBERS ARE PRINTED ON TUBULAR PARTS
CP20B2
CP20B1
CP20B1
CP20B2
SAFETY BOLT HOLES AS
SHOWN TO REAR. THIS
WILL LOCATE THE TUBE
IN FINAL ASSEMBLY.
CONNECT PARTS TOGETHER,
HAND TIGHTEN CHICAGO BOLTS.
CP20B1
CP20B2
CP20B1
CP20B2

SAFETY BOLT HOLES
AS SHOWN!
SLIDE ON SWING CLAMPS AND
HAND TIGHTEN CHICAGO BOLTS.
NOTE CLAMP BOLTS FACING
INWARDS. LOCATE SAFETY BOLT
HOLE AND TIGHTEN INTO TUBE
CP20C1
CP20C2
NOTE CLAMP SCREWS
BOTH FACING INWARDS!!
FRONT SUPPORT BAR: IMPORTANT! LAY PARTS OUT AS SHOWN.
SWING CLAMPS FOUND
IN TP1 TRAPEZE BOX.

STEP 1: POSITION CARGO NET ONTO LADDER AS SHOWN - NO LOOPS TO BOTTOM
MONKEY BARS (MR1800KIT):
IMPORTANT! LAY PARTS OUT AS SHOWN.
NO LOOPS
STEP 2: CONNECT MONKEY BARS
INTO CLAMPS. NOTE THAT
BRACES ARE FACING TOWARDS
REAR
BRACING TO REAR
SHORT TEE WITH
SAFETY BOLT
TWO PEOPLE ARE NOW
REQUIRED FOR REMAINING
ASSEMBLY!

STEP 3: PLACE RIGHT HAND
TOP RAIL ONTO LADDER AS
SHOWN AND TIGHTEN
BOTTOM BOLTS ONLY.
DON’T TIGHTEN THE
SAFETY BOLT!
RIGHT HAND TOP RAIL
NOTE END CAPS TO REAR
STEP 4: SLIDE 1 X ROPE
CLIMB AND 1 X SWING
CLAMP AS SHOWN.
SWING CLAMP FOUND
IN NS2 BOX (NET
SWING)
TOP SIDE RAILS
SAFETY BOLT
TO OUTSIDE

PLACE SWING CLAMP BETWEEN FIRST
AND SECOND CARGO LOOP FIRST!
STEP 5: PLACE LEFT HAND
TOP RAIL ONTO LADDER
AS SHOWN AND TIGHTEN
BOTTOM BOLTS ONLY.
DON’T TIGHTEN SAFETY
BOLT!
STEP 6: SLIDE 1 X CARGO
LOOP, THEN 1 X SWING
CLAMP AS SHOWN (SWING
CLAMPS FOUND IN NS2
BOX)
SLIDE ON THE 5 REMAINING
CARGO NET LOOPS
ATTACH CP20A1 WITH
CHICAGO BOLTS.
NOTE END CAPS TO REAR
LEFT HAND TOP RAIL
TOP SIDE RAILS
CP20A1
CP20A1
ONE PERSON IS REQUIRED TO
SUPPORT FRAME AT ALL TIMES!
SAFETY BOLT
TO OUTSIDE

STEP 7: ATTACH
CP20A1 WITH
CHICAGO BOLTS
AND SLIDE ON
REMINING ROPE
CLIMBS. LEAVE
LOOSE.
CP20A1
STEP 8: GRAB FRONT SUPPORT BAR FOR NEXT STEP

STEP 9: ATTACH FRONT
SUPPORT BAR ONE SIDE AT
A TIME. LOOSLY TIGHTEN
WITH ALLEN KEY.
SAFETY BOLT HOLES AS SHOWN
TO INSIDE!!

NOTE LEGS FACING
OUTWARDS
PLAN VIEW
SAFETY BOLT HOLES AS
SHOWN!!
THREAD LEG THROUGH
CARGO NET AND INTO TOP
CLAMP. ROTATE UNTIL
SAFETY BOLT HOLE IS
SHOWN AND INSERT SAFETY
BOLT

BOTTOM SIDE RAILS
THREAD BOTTOM SIDE RAILS
THROUGH CARGO NET AND
INTO TOP CLAMP. ROTATE
UNTIL SAFETY BOLT HOLE IS
SHOWN AND INSERT SAFETY
BOLT. REPEAT OTHER SIDE.
SAFETY BOLT TO
OUTSIDE
CP20B1
CP20B2

ONCE ALL BOLTS ARE TIGHTENED ON
FRAME, MOVE INTO POSITION.
INSTALL PEGS TO HOLD BASE PLATE IN
PLACE ONE CORNER AT A TIME, LOOSEN
AND LIFT FRAME TO ONE SIDE LEAVING
BASE PLATE IN PLACE. SCREW GROUND
ANCHOR AND WASHER THROUGH BASE
PLATE UNTIL FIRMLY SEATED. LIFT FRAME
BACK INTO BASE PLATE AND TIGHTEN.
REPEAT ALL 4 CORNERS.
WARNING: ACCESSORIES MUST ONLY BE ATTACHED IN
POSITIONS AS SHOWN IN THESE INSTRUCTIONS.
FAILURE MAY RESULT IN DEATH OR SERIOUS INJURY.