growplay GP1-KD Quick guide

Assembly, Maintenance and User
Instructions Manual
WARNING !
READ ALL PRECAUTIONS AND INSTRUCTIONS IN THIS MANUAL
BEFORE USING THIS EQUPIMENT.
KEEP MANUAL IN A SAFE PLACE FOR FUTURE
REFERENCE.MAXIMUM OCCUPANCY = 10 USERS @ <50KG
TOTAL WEIGHT CAPACITY = 500KG
AGE OF USERS 3+
GROWPLAY MONKEYBARS ® PTY. LTD.
ABN : 36 627 796 141
P.O Box 2527,Clarkson, WA , 6030
Model :GP1-KD REV 4
CERT : EN71-8:2018
CLICK HERE FOR FULL ASSEMBLY VIDEO INSTRUCTIONS
https://youtu.be/SzLE9fCtxxk

BEFORE YOU BEGIN
Thank you for purchasing Growplay Monkey Bars. With regular maintenance, your set will
provide many years of backyard fun.
Before you start to assemble your new GROWPLAY MONKEY BAR SET please ensure that
you have read this important information and that it is communicated to all users prior to
use.
INSTALLATION WARNING!
•Read all important precautions and instructions in this manual and all warnings on
the equipment to reduce the risk of serious injury.
•It is the responsibility of the owners and supervisors of this equipment to ensure
that it has been correctly assembled, anchored, maintained and the users obey the
safety instructions.
•This product is intended for use by children AGE OF USERS 3+
•Until the equipment has been correctly assembled and anchored, do not let children
use equipment.
•Always use Growplay Monkey Bars under adult supervision.
•It is required that the play equipment be ground anchored with the ground anchor
nails provided onto a soft or shock absorbing surface.
•Do not install over concrete or any other hard surface as a fall onto a hard surface
could result in serious injury or death.
•Ensure that the equipment is installed on a level surface and no less than 1.8 metres
from any structure or obstruction.
•Always inspect the equipment before it is used and replace any worn, defective, or
missing parts.
•Ensure that all connectors are regularly checked.
ELECTROCUTION HAZARD
Growplay monkey bars are made from metal. They are not grounded and will conduct
electricity. For obvious reasons and electrocution hazard exists. NO lights, heaters, electrical
and extension cords or any household electrical device or appliances are to be permitted on
or in the frame at any time.
WARNING: THIS DISASSEMBLED PRODUCT MAY CONTIAN SMALL PARTS
WHICH POSE A CHOKING HAZARD TO CHILDREN UNDER 3.
WARNING: ACCESSORIES MUST ONLY BE ATTACHED IN POSITIONS AS SHOWN IN
THESE INSTRUCTIONS. FAILURE MAY RESULT IN DEATH OR SERIOUS INJURY.

FOR FULL STEP BY STEP VIDEO INSTRUCTIONS
SEARCH GROWPLAY ORIGINAL RANGE ON
YOUTUBE
FOR THE USER
•Do not use this equipment when under the influence of drugs or alcohol.
•Do not jump on or off the frame.
•Wear clothing that does not have loops, hooks, drawstrings, or anything else that
can get caught on the frame.
USER INSTRUCTIONS
1. GROWPLAY MONKEY BARS are designed for up to 6 persons and not exceeding total
weight of 500kg.
2. AGE OF USERS 3+
3. Adult supervision for children of all ages is required at all times.
4. Educate children not let to walk close to, behind and in front, between moving parts.
5. Children are not to use the equipment in any other manner than intended.
6. Teach children not to hop off equipment while in motion or jump from moving play
items.
7. Do not twist chains or ropes or loop them over support bars as this may reduce the
structural integrity of the rope or chain.
8. Do not allow use of the equipment when it is wet as injury due to slips may occur.
9. Children are to be dressed in appropriate clothing while playing on or around the
equipment with correctly fitted and full foot enclosing footwear. Loose fitting items,
hood, and neck draw strings etc could potentially cause injury or death by
strangulation.
10. Inform children not to attach items to the playground equipment that are not
specifically designed or approved for use with the Growplay monkey bar equipment,
such as, but not limited to jump ropes, clothesline, pet leashes, cables, and chain as
they may cause a strangulation hazard.

ASSEMBLY: TWO PERSONS
Before starting assembly, please carefully read the following information.
•Two people are required to assemble frame.
•DO NOT FULLY TIGHTEN BOLTS UNTIL FRAME IS ASSEMBLED.
•Place all parts in one cleared area and remove the packaging material. Do not throw
away material until assembly is complete.
•Dispose of the packaging thoughtfully and ensure any plastic bags and small parts
are kept away from children or pets.
•Ensure that you check all tightening of parts twice and that the frame is stable after
assembly. Small movement through the frame is normal.
•Allow plenty of time to ensure that your monkey bars are set up correctly and safe to
use.
•Ensure that no exposed red tape is present and that all fixtures are extremely tight.
ENSURE THE TUBE IS
CORRECTLY INSERTED
NO RED TAB SHOULD BE
VISIABLE.

ENSURE GROUND IS LEVEL AND USE GROUND
ANCHOR SCREWS AND PEGS PROVIDED.

GP1-KD ORIGINAL FRAME CONTENTS
DESCRIPTION
SKU
QTY
BARCODE
ORIGINAL ACCESSORIES KIT
GPAC
1
794712825524
TUBE ASSEMBLY 1
TA1
1
794712825494
TUBE ASSEMBLY 2
TA2
1
794712825500
TUBE ASSEMBLY 3
TA3
1
794712825517
LD1 LADDER
LD1
2
794712825265
MONKEY RUNG 1800
MR1800KIT
1
794712825258

TAKE YOUR TIME! THIS IS HOW YOUR FRAME SHOULD LOOK
WHEN COMPLETE.
FOR SAFETY AND STABILITY, SUPPORT BARS MUST BE
POSITIONED AS SHOWN, ~15-30 DEG ANGLE.

WARNING ! ENSURE THAT
THE RED WARNING
LOCATOR TAPE CAN NOT
BE SEEN. IF YOU CAN NOT
SEE THE RED TAPE THEN
THE TUBE IS IN CORRECTLY.
ENSURE THAT YOU CHECK
AND TIGHTEN EACH
CONNECTOR SEVERAL
TIMES BEFORE USE. WHEN
WE SAY TIGHT, WE MEAN
AS TIGHT AS YOU CAN
POSSIBLY GO. YOU WON’T
DAMAGE IT.
TYPICAL SWING
HOOK AND FOOT
PEG ASSEMBLY.
PLACE AROUND
TUBE AND TIGHTEN
WITH SPANNER
PROVIDED ONCE IN
POSITION.
REGULARY CHECK
AND TIGHTEN.
1 PEG PER FOOT
TYPICAL CLAMP, SWING HOOK &
FOOT ASSEMBLY

TYPICAL CHICAGO BOLT AND TUBE ASSEMBLY
IMPORTANT! ONLY FULLY TIGHTEN BOLTS ONCE FRAME IS
ASSEMBLED. FINGER TIGHTEN ONLY DURING ASSEMBLY.
TYPICAL RUNG ASSEMBLY
REFER TO PART NUMBERS
PRINTED ON TUBULAR
PARTS ASSEMBLY.
B1040
M
BC1040F
LDB
LDA
ROCK GRIP ASSEMBLY
B1035BH1
B1035BH1
B1060BH

ASSEMBLE MONKEY RUNG AS SHOWN. INSTALL CLAMPS TO LD1 LADDER IN NEXT STEP

REMOVE LADDERS FROM BOX 1 AND BOX 2
•INSTALL SHORT TEES FOR DIP BARS (LEAVE LOOSE) ONE SIDE.
•INSTALL SHORT TEE CLAMPS AT EQUAL HEIGHTS FOR MONKEY BARS.
DO NOT FULLY TIGHTEN UNTIL NEXT STEP.
DIP BAR CLAMPS
PLACE CLAMPS AT
EQUAL HEIGHTS
SLIDE ON ADDITIONAL
CLAMPS IF ATTACHING
MK1800 OR MK2400
EXTENTION KIT FOR X
RANGE!

WASHER
MRA
CUB1
MRB
MRC
REDUCER-T
CF20CB2
SWING
CLAMP
SHORT-T
B1035BH1
WASHER
B1035BH1
SWING
CLAMP
ASSEMBLE ACCESSORY BAR AS SHOWN. SET T-CLAMPS ASIDE FOR LATER
STEP.
COMPLETED ACCESSORY BAR.
SET ASIDE
FPB
FPC
ASSEMBLE FIREMANS POLE AS SHOWN & SET ASIDE.
B1040F/M
B1040F/M
FOOT

ASSEMBLE DIP BAR LEGS
CF20CB2
DBR2,
B1035BH1,
WASHER
DBR2
FOOT
CNC
ASSEMBLE DIP BAR TOP RAIL X 2
SHORT –T
TIP!
USE 6MM HEX KEY TO SET
CLAMPS AT EQUAL LENGTHS.

ASSEMBLE TUMBLE & GYMNASTICS BAR
TWA
TWB
ELBOW
FOOT
CNC
CNB
CNA
FOOT
ELBOW
B1040F/M
ASSEMBLE 4 X GREY POLES
LDC
LDB
B1040F/M

PLACE LADDERS ON SIDE AND INSERT MONKEY RUNGS INTO CLAMPS
BRACES. ENSURE THAT RED TABS ARE NOT SHOWING BEFORE TIGHTENING.
DIP BAR
CLAMPS THIS
END
STAND FRAME UPRIGHT AND
ATTACH TUMBLE BAR FOR
STABILITY DURING ASSEMBLY
ROCK GRIPS AND
BRACING FACING
DOWN

SLIDE SHORT TEE’S UP TO JOINS ON 2 X GREY CROSSBARS. TIGHTEN ONE
ONLY AT JOIN.
TIGHTEN. NOTE
ORENTATION OF CLAMP IS
COVERING JOIN
CLAMP IS
COVERING TUBE
JOIN. BOLTS
FACING UPWARDS.
ATTACH TOP RAILS TO FRAME
LADDERS AND TIGHTEN.

SLIDE ON 6 X SWING CLAMPS AND 3 X SHORT TEE’S ONTO TOP RAIL.

SHORT TEE IS
ABOVE BOLTS FOR
CARGO NET SIDE
SHORT-TEE IS
BELOW BOLTS FOR
TUMBLE BAR SIDE
LEFT HAND SIDE. SLIDE
DOWN 1 X SHORT-TEE
1 X REDUCER-TEE AND
1 X SHORT-TEE
RIGHT HAND SIDE
SLIDE DOWN 1 X
REDUCER-TEE X 1
SHORT-TEE
ATTACH FOOT
SLIDE UP 1 X
SHORT TEE
AND ATTACH
FOOT
CONNECT FRAME AND
TIGHTEN. LEAVE LOWER
SHORT-TEES FINGER
TIGHT ONLY AT THIS
STAGE

INSERT LEGS INTO SHORT-TEES AND LIGHTLY TIGHTEN.
REMOVE
TUMBLE BAR
SUPPORT
INSTALL 4 X
END CAPS
AND TIGHTEN
SHORT-TEE