HAMMON MANUFACTURING ECLIPSE Series User manual

HAMMOND
MANUFACTURING TM
ENCLOSURES
TOOL BOX
BUL10248
ECLIPSE - SERIES
ASSEMBLY INSTRUCTIONS FOR POINT LATCHING
SYSTEM ON SINGLE DOOR ECLIPSE ENCLOSURES
REV. B
PAGE 1 OF 2
Pliers
7/16", 27mm, 17mm,
10mm Socket Wrench
THREADEDSTUD
ON INSIDE OF DOOR
SEE STEP C
1
2
3
4
5
6
7
8
10
9
PART # QTY. DESCRIPTION
1 1 L HANDLE KEY LOCKABLE
2 1 GASKET
3 2 CAM SPACER
4 2 TOP AND BOTTOM ROLLER
CAM
5 2 NYLON WASHER
6 2 LOCK NUT
7 3 C RETAINING CLIP
8 1 LOCK ROD
9 1 HANDLE HEX NUT (27mm)
10 1 HANDLE HEX BOLT (7/16)
11 1 CENTER ROLLER CAM
12 1 HANDLE HEX NUT (17mm)
THREADED BARREL
ON L HANDLE
SEE STEP A
ECLIPSE SINGLE DOOR
SHOWN WITH 3 PT LATCHING
SYSTEM ON RIGHT SIDE OF DOOR
ASSEMBLY INSTRUCTIONS
A)
B)
C)
D)
E)
INSERT SHAFT OF L HANDLE (PART 1) WITH GASKET (PART 2)
THROUGH CENTER HOLE IN DOOR. HANDLE RUNS PARALLEL TO THE
SIDE OF THE DOOR IN CLOSED POSITION. INSERT THE HANDLE BOLT
(PART 10) THEN HANDLE NUT (PART 9) ONTO THREADED BARREL OF
HANDLE AND TIGHTEN BOTH.
MOUNT CENTER ROLLER CAM (PART 11) ONTO THE SHAFT OF THE
HANDLE AS SHOWN AND FASTEN USING THE HEX HD SCREW (PART
12). KEEP ROLLER CAM FACING OUT 90 DEGREES TO L HANDLE IN
CLOSED POSITION.
SLIP CAM SPACER (PART 3) ON THREADED POSTS ON THE TOP AND
BOTTOM OF DOOR. SLIP THE ROLLER CAM (PART 4) ONTO THE
SPACER AND TIGHTREN USING A LOCK NUT AND NYLON WASHER
(PARTS 5 & 6).
MOUNT THE LOCK ROD (PART 8) TO ALL THREE ROLLER CAMS BY
SLIPING THE ROD OVER EACH PIN ON EACH CAM AND THEN SECURE
IN PLACE WITH THE C RETAINING CLIP (PART 7). ALL THREE ROLLER
CAMS SHOULD LOOK THE SAME IN CLOSED POSITION AS ABOVE.
UNLOCK L HANDLE AND TURN CLOCKWISE AS SHOWN TO THE OPEN
POSITION. CLOSE THE DOOR AND TURN THE HANDLE BACK
COUNTER CLOCKWISE TO CLOSE. LOCK THE DOOR USING THE KEY
PROVIDED TO SECURE CONTENTS IN THE ENCLOSURE.
11
12

HAMMOND
MANUFACTURING TM
ENCLOSURES
TOOL BOX
BUL10248
ECLIPSE - SERIES
ASSEMBLY INSTRUCTIONS FOR 3 POINT LATCHING
SYSTEM ON TWO DOOR ECLIPSE ENCLOSURES
REV. B
Pliers
7/16", 27mm, 17mm,
10mm Socket Wrench
PART # QTY. DESCRIPTION
1 1 L HANDLE KEY
LOCKABLE
2 1 GASKET
3 1 HANDLE HEX NUT
4 1 HEX HD SCREW
5 1 CENTER ROLLER CAM
6 2 TOP AND BOTTOM
ROLLER
7 2 CAM SPACER
8 2 LOCK ROD
9 2 LOCK NUT
10 2 NYLON WASHER
11 4 C RETAINING CLIP
12 4 CENTER FLAT CAM
ASSEMBLY INSTRUCTIONS
(A) INSERT SHAFT OF L HANDLE (PART 1) WITH GASKET (PART 2) THRU
CENTER HOLE IN DOOR. HANDLE RUNS PARALLEL TO SIDE OF DOOR
IN CLOSED POSITION. TUIRN HANDLE NUT (PART 3) ONTO
THREADED BARREL OF HANDLE AND TIGHTEN.
(B) MOUNT CENTER FLAT CAM (PART 12) ONTO SHAFT OF HANDLE AS
SHOWN AND FASTEN USING THE HEX HD SCREW (PART 4). KEEP
FLAT CAM FACING OUT 90 DEGREES TO L HANDLE IN CLOSED
POSITION.
(C) SLIP CAM SPACER (PART 7) ON THREADED POSTS ON TOP AND
BOTTOM OF DOOR. SLIP ROLLER CAM (PART 5) ONTO SPACER AND
TIGHTEN USING LOCK NUT AND NYLON WASHER (PARTS 9 & 10).
NOTE: THE ROLLER CAMS SHOULD FACE TO THE TOP AND BOTTOM
OF THE DOOR OPENING.
(D) MOUNT LOCK RODS (PART 8) TO ALL THREE CAMS BY SLIPPING
THE ROD OVER EACH PIN ON EACH CAM AND SECURE IN PLACE
WITH THE C RETAINING CLIP. THE ROLLER CAMS SHOULD FACE TO
THE TOP AND BOTTOM OF THE DOOR OPENING AND CENTER FLAT
CAM SHOULD FACE OUT 90 DEGREES IN CLOSED POSITION AS
ABOVE. DOUBLE CHECK THAT THE LOCK RODS ARE FASTENED TO
THE CAMS AS SHOWN.
(E) UNLOCK L HANDLE AND TURN COUNTER CLOCKWISE TO OPEN
POSITION. CLOSE DOOR AND TURN HANDLE BACK CLOCKWISE TO
CLOSE. LOCK DOOR USING KEY PROVIDED TO SECURE CONTENTS
OF ENCLOSURE. ALWAYS CLOSE THE MATING DOOR FIRST THEN
THE LOCKING DOOR.
1
2
THREADED BARREL
ON L HANDLE
SEE STEP A THREADED
POST ON INSIDE
OF DOOR
SEE STEP C
ECLIPSE LOCKING DOOR
SHOWN WITH 3 PT
LATCHING FOR THE TWO
DOOR ENCLOSURE
NOTE: DISCARD CENTER ROLLER
CAM (PART 5) FOR 2 DOOR
ENCLOSURE ONLY.
3
4
5
6
7
8
8
9
10
11
12
PAGE 2 OF 2