Hammond Manufacturing ECLIPSE Series User manual

PAGE 1 OF 3
ECLIPSE SERIES
ASSEMBLY INSTRUCTIONS FOR
SWING PANEL& SWING FRAME REV. F
HAMMOND
MANUFACTURING TM
ENCLOSURES
TOOL BOX
5/32 ALLEN KEY
3/8,7/16" Socket
Wrench
3/8 or 7/16
Open
Wrench
Centre
Punch
Drill, use
.281(7.1mm) BIT
Hammer
C
L
FIG. 1
0.994
25.25mm
MINIMUM 4.370
111mm
2.000
50.8mm
2.000
50.8mm
BUL10120
CENTER HOLES
REQUIRED WHEN
ENCLOSURE HEIGHT
GREATER THAN 42"
1) DRILL HOLES IN ENCLOSURE FOR FIELD INSTALLED KITS (FIG. 1)
a) MARK AND DRILL 0.281" (7.1mm) DIA HOLES 4 or 6 PLACES
BOTH SIDES
O
0.281
7.14mm
PART # QTY. DESCRIPTION
1 1 SWING PANEL/FRAME
2 1 VERTICAL RAIL LOCK SIDE
3 1 VERTICAL RAL HINGE SIDE
4 4 OR 6 C-CHANNEL
5 2, 3 OR HINGE PIN
6 4 OR 6 1/4-20 SCREW
7 4 OR 6 1/4-20 C-CHANNEL NUT
8 8 OR 1/4-20 BUTTON HEAD SCREW
9 8 OR 1/4-20 SEALING WASHER
10 8 OR 1/4-20 KEP NUT
11 1 FINGER PULL
12 2, 3 OR HINGE PIN CAP
13 2 1/4 TURN LATCH

PAGE 2 OF 3
ECLIPSE SERIES
REV. F
HAMMOND
MANUFACTURING TM
ENCLOSURES
TOOL BOX
5/32 ALLEN KEY
3/8,7/16" Socket
Wrench
3/8 or 7/16
Open
Wrench
Centre
Punch
Drill, use
.281(7.1mm) BIT
Hammer
BUL10120
FIG. 3
FIG. 2
2) MOUNT C-CHANNELS (FIG. 2):
a) PLACE 1/4-20 BUTTON HEAD SCREWS THROUGH SEALING WASHERS
THEN THROUGH HOLES IN ENCLOSURE WITH RUBBER SIDE FACING
ENCLOSURE.
b) INSTALL C-CHANNEL ONTO 1/4-20 SCREWS
c) INSTALL 1/4-20 NUTS ONTO 1/4-20 SCREWS
10
498
3) INSTALL VERTICAL RAILS (FIG. 3):
a) INSTALL C-CHANNEL NUTS IN C-CHANNELS
b) PLACE HINGED VERTICAL RAIL ON DESIRED SIDE FOR SWING
OPENING.
c) INSTALL 1/4-20 SCREWS INTO C-CHANNEL NUT TO HOLD VERTICAL
RAIL IN PLACE.
4
7
6
2
3
ASSEMBLY INSTRUCTIONS FOR
SWING PANEL& SWING FRAME

PAGE 3 OF 3
ECLIPSE SERIES
REV. F
HAMMOND
MANUFACTURING TM
ENCLOSURES
TOOL BOX
5/32 ALLEN KEY
3/8,7/16" Socket
Wrench
3/8 or 7/16
Open
Wrench
Centre
Punch
Drill, use
.281(7.1mm) BIT
Hammer
BUL10120
FIG. 4
4) MOUNT SWING PANEL / FRAME TO HINGE VERTICAL RAIL (FIG. 4)
a) PLACE SWING PANEL / FRAME HINGE BARRELS BETWEEN VERTICAL
RAIL HINGE.
b) INSERT PINS THROUGH HINGE AND BARREL.
c) INSERT PIN CAPS
FIG. 6
LOCK RANGE OF MOTION
OPPOSITE WAY FOR
OTHER LOCK
5) INSTALL 1/4 TURN LATCHES AND FINGER PULL IF REQUIRED (FIG. 5 & 6)
a) REMOVE NUT FROM 1/4 TURN LATCHES
b) INSERT 1/4 TURN LATCH THROUGH FINGERPULL
c) INSERT 1/4 TURN LATCH INTO SWING FRAME PANEL LATCH CUT OUT
d) ENSURE LATCHES ROTATE AS SHOWN IN FIG. 5
e) INSTALL NUT BACK ONTO1/4 TURN LATCHES
12
5
3
1
FIG. 5
ASSEMBLY INSTRUCTIONS FOR
SWING PANEL& SWING FRAME
11
13
1