Hammond ECLIPSE Series User manual

HAMMOND
MANUFACTURING
TM
TOOL BOX
www.hammondmfg.com
PAGE 1 OF 4
ECLIPSE SERIES
ASSEMBLY INSTRUCTIONS FOR
SWING PANEL AND SWING FRAME
BUL10120
REV. H
5/32 ALLEN KEY
3/8,7/16" Socket
Wrench
3/8 or 7/16
Open
Wrench
Centre
Punch
Drill, use
.281(7.1mm) BIT
PARTS LIST
PART # QTY. DESCRIPTION
1 1 SWING PANEL/FRAME
2 1 VERTICAL RAIL LOCK SIDE
3 1 VERTICAL RAIL HINGE SIDE
4 2 MOUNTING BRACKET (1)
5 2 MOUNTING BRACKET (2)
62-4 HINGE PIN
72-4 RUBBER PIN CAP
8 8 1/4-20 BUTTON HEAD SCREW
9 8 SEALING WASHER
10 41/4-20 CAGE NUT
11 41/4-20 SCREW
12 1FINGER PULL
13 21/4 TURN LATCH
FIG. 1
1. Drill holes for mounting brackets. (Fig. 1)
a) Place mounting bracket on top left corner of enclosure. Mark two holes.
b) Place mounting bracket on bottom right corner of enclosure. Mark two holes.
c) Place mounting bracket on bottom left corner of enclosure. Mark two holes.
d) Place mounting bracket on top right corner of enclosure. Mark two holes.
e) Drill marked holes with 0.281"drill bit.
4
5
4
5
FLUSH WITH
FLANGE
Z
DETAIL Z
MARK THESE HOLES

HAMMOND
MANUFACTURING
TM
TOOL BOX
www.hammondmfg.com
PAGE 2 OF 4
ECLIPSE SERIES
ASSEMBLY INSTRUCTIONS FOR
SWING PANEL AND SWING FRAME
BUL10120
REV. H
5/32 ALLEN KEY
3/8,7/16" Socket
Wrench
3/8 or 7/16
Open
Wrench
Centre
Punch
Drill, use
.281(7.1mm) BIT
FIG. 2
2. Pre-assemble mounting brackets. (Fig. 2)
a) Insert cage nut in square cut out of mounting bracket.
(Review table for desired spacing)
10
SQUARE CUT OUT SPACING BETWEEN SWING
PANEL AND INSIDE OF DOOR
FRONT 2.675"
BACK 3.425"
FIG. 3
9
8
3. Install mounting brackets. (Fig. 3)
a) Assemble button head screws and sealing washers. Ensure rubber side
of sealing washer is facing enclosure.
b) Insert assembled button head screw and sealing washer through drilled
holes and attach to mounting bracket tighten using allen key.
5
5
4
4

HAMMOND
MANUFACTURING
TM
TOOL BOX
www.hammondmfg.com
FIG. 4
4. Install vertical rails. (Fig. 4)
a) Insert 1/4-20 screw through slot in vertical rail hinge side. Tighten screw by hand.
b) Adjust vertical rails to desired location and tighten screw using 3/8 wrench.
c) Repeat steps for vertical rail lock side.
3
11
FIG. 5
5. Install 1/4 turn latches. (Fig. 5)
a) Remove nut from 1/4 turn latchs.
b) Insert 1/4 turn latch through finger pull.
c) Insert 1/4 turn latch into swing panel latch cut out.
d) Ensure latches rotate as shown. (Fig. 6)
e) Install nut back onto 1/4 turn latches.
FIG. 6
RANGE OF MOTION
OPPOSITE WAY FOR
OTHER LOCK
ECLIPSE SERIES
ASSEMBLY INSTRUCTIONS FOR
SWING PANEL AND SWING FRAME
BUL10120
REV. H
PAGE 3 OF 4
5/32 ALLEN KEY
3/8,7/16" Socket
Wrench
3/8 or 7/16
Open
Wrench
Centre
Punch
Drill, use
.281(7.1mm) BIT

HAMMOND
MANUFACTURING
TM
TOOL BOX
www.hammondmfg.com
PAGE 4 OF 4
5/32 ALLEN KEY
3/8,7/16" Socket
Wrench
3/8 or 7/16
Open
Wrench
Centre
Punch
Drill, use
.281(7.1mm) BIT
ECLIPSE SERIES
ASSEMBLY INSTRUCTIONS FOR
SWING PANEL AND SWING FRAME
BUL10120
REV. H
FIG. 7
6. Install swing panel/frame. (Fig. 7)
a) Place swing panel/frame hinge barrels between vertical rail hinges.
b) Insert pins through hinge and barrel.
c) Insert pin caps.
1
6
7