hayneedle EWB003 User manual

Assembly Instructions For Christmas Tree
YOUR NEW INCLUDES THE FOLLOWING FEATURES
Super-bright bulbs
Professionally wrapped light strings
Easy, fast assembly and disassembly
Flame-retardant, natural looking tree
Reusable storage carton
Assembling your tree:
1. Open and secure the positioning of the tree stand by fastening the screws at the
base of the stand.
2. Insert the bottom section of the tree into the stand, and secure it by fastening the
screws tightly at the top of the stand.
3. Attach the middle 1 section of the tree to the bottom section by inserting the base
of the middle 1 section into the top of the bottom section.
4. Attach the middle 2 section of the tree to the middle 1 section by inserting the base
of the middle 2 section into the top the middle 1 section.
5. Attached the top section of the tree (tree top) to the middle 2 section by inserting
the base of the top section into the top of middle 2 section.
6. Allow branches to fall into place and gently pull out and down. When adjusting
branches, be sure that all wires are free of branch hinges.
7. Locate the extension cords and connect together as indicated in diagram. Plug the
long extension cord into the wall. If bulbs do not light, search for loose plug or
missing bulbs and replace any defective bulbs.
8. Unplug the lights and shape your tree.

-Connect the male and female plug with yellow label
of top and Middle sections.
-Fasten screws to secure
tree into the stand.
Top
Middle 2
Middle 1
Bottom
-ADDITIONAL EXTENSION CORD
-CAUTION: IF CONNECT OTHER LIGHTING STRINGS OR
DECORATIVE OUTFITS END-TO-END UP TO A MAXIMUN
OF 210 WATTS (1.75Amps) TOTAL, PLEASE USE ADDITIONAL
EXTENSION CORD TO PLUG INTO THE WALL OUTLET.
-INSERT THE MALE PLUG OF ADDITIONAL
EXTENSION CORD INTO WALL OUTLET.
- INSERT THE MALE PLUG WITH BLUE LABEL OF
MIDDLE 1 INTO FEMALE PLUG OF ADDITIONAL
EXTENSION CORD.
-INSERT THE MALE PLUG OF BOTTOM SECTION INTO
FEMALE PLUG OF ADDITIONAL EXTENSION CORD.
- INSERT THE MALE PLUG WITH RED LABEL OF MIDDLE 2 INTO
FEMALE PLUG OF ADDITIONAL EXTENSION CORD.

STORAGE:
1. Unplug extension cord from the wall outlet.
2. Unplug each section of extension cord.
3. Gently lift off the top and middle sections, and remove the bottom section from the
tree stand.
4. Carefully place the tree in its box and tape it shut. Store box in a cool dry and
place the temperature does not exceed 100 °F.
CAUTION:
1. Do not allow metal objects to come in contact with lights or wires.
2. Do not use lights if wire insulation is damaged.
3. Do not overload. Connect only miniature light strings.
4. This pre-lit tree contains 50/100/150 lamps per string. To reduce the risk of
overheating, replace with 2.5 volts lamp only.
5. Use on 115-125 volts outlet only.
PRELACEMENT:
To replace burned-out bulbs, follow directions below:
1. Make sure the set is unplugged.
2. Pull bulbs and base straight out of socket.
3. Inset replacement bulbs and base into empty socket, making sure base is
connected.
4. Plug light set back in wall outlet.
Important: If the light set does not light, push each bulb firmly into the socket.
Bulbs may have loosened during transportation.
CATUION:
-BURNED OUT BULBS SHOULD BE REPLACED QUICKLY. SEVERAL
BURNED OUT BULB LEFT MAY CAUSE OTHERS TO BURN OUT.
-TO REDUCE THE CHANCE OF EXCESSIVE HEAT AND DAMAGE DO NOT
ATTACH DECORATIVE FEATURES TO BULBS.
-TO REDUCE THE RISK OF FIRE AND ELECTRICAL SHOCK. DO NOT PLACE
TREE NEAR OPEN FLAMES.
-KEEP LIGHT OUT OF THE REACH OF YOUNG CHILDREN.
-TURN SET OFF WHEN LEAVING HOME OR RETIRING AT NIGHT.
-DO NOT OVERLOAD. CONNECT ONLY MINIATURE LIGHT.
-FOR INDOOR OUR OUTDOOR USE 115-125 VOLTS A.C.
-DO NOT CONNECT MORE THAN 3 SETS.DO NOT CONNECT WITH
STANDARD C-7 OR C-9 LIGHT SETS OR STRINGS.A SHORT CIRCUIT
AND/OR FIRE MAY RESULT.