Home Accents Holiday TG90P2082C01 User manual

Safety Information
Pre-Assembly
IMPORTANT SAFETY
INSTRUCTIONS
a.READ AND FOLLOW ALL
SAFETY INSTRUCTIONS.
When using electrical products, basic precautions should
always be followed, including the following:
b.Do not use seasonal products outdoors unless marked
suitable for indoor and outdoor use. When products are
used in outdoor applications, connect the product to a
Ground Fault Circuit Interrupting (GFCI) outlet. If one is not
provided, contact a qualified electrician for proper installa-
tion.
c. This seasonal product is not intended for permanent
installation or use.
d.Do not mount or place the product near gas or electric
heaters, fireplaces, candles, or other similar sources of
heat.
e.Do not secure the wiring of the product with staples or
nails, or place on sharp hooks or nails.
f. Do not let lamps rest on the supply cord or on any wire.
g.Unplug the product when leaving the house, when
retiring for the night, or if left unattended.
h.This is an electric product and not a toy! To avoid risk of
fire, burns, personal injury and electric shock it should not
be played with or placed where small children can reach it.
i. Do not use this product for other than its intended use.
j. Do not hang ornaments or other objects from cord, wire,
or light string.
k.Do not close doors or windows on the product or exten-
sions cords as this may damage the wire insulation.
l. Do not cover the product with cloth, paper, or any material
that is not a part of the product when in use.
m.This product is equipped with push-in type lamps. Do not
twist lamps.
n.Read and follow all instructions that are on the product
or provide with the product.
o.SAVE THESE INSTRUCTIONS
Package Contents
Assembly
Do Not Tamper
Internal Parts
Open the
protective
cover
Do Not Tamper
Internal Parts
Open the
protective
cover
Do Not Tamper
Internal Parts
Open the
protective
cover
Christmas Tree
Model: TG90P2082C01
Sku # 0000 000 000
Step 1.Pull apart the legs of the stand so that they are
snapped into an x-shape, place the tree stand on a
level surface.
To close the stand, press the metal button and fold the legs
together.
Assembling the tree
This tree assmebles with Quick Set® technology
---Set up and light up your tree in less than 10 minutes!
Step 1.Remove the protective caps from the tree bottom
and insert the pole into the tree stand.
Step 2.Continue by inserting the upper tree section(s) to
the lower section(s) until inserting the tree top.
Step 3.Shape the branches to your preference by working
from the bottom to the top. When adjusting
branches, ensure that all wires are free of branch
hinges.
Step 4.Insert the adaptor into the wall outlet. All your lights
should now be lit.
Step 5.When finished shaping the branches, slightly
upsweep all branch tips for a uniform look.
Assembling the tree stand
Click
Part Description Quantity
E Tree stand 1
B Tree top, tag 3 1
A Tree top, tag 4 1
C Tree center, tag 2 1
D Tree bottom, tag 1 1
Section 1
Section 2
Section 3
Section 4
Insert
Green Label
Plug Into Wall
Outlet
Foot Pedal
on/off Switch
100S
100S
50S
50S
100S
100S
50S
100S
100S
100S
100S

NOTE: If some bulbs do not light or flicker, search for any
loose plugs and/or broken, loose, or missing bulbs. Replace
bulbs promptly with the replacement bulbs provided in
order to maintain the performance and life expectancy of
your tree.
Step 1. Connect the light strings of the tree together and
plug the power cord into a wall outlet.
Step 2. If the tree comes with a foot pedal, step on the
On/Off button.
Press the selector button on the “Dual Color Light Control
ler” or “Remote Controller” to select among: (1) CLEAR AND
MULTI-COLOR ALTERNATING; (2) CLEAR LIGHTS; (3)
MULTI LIGHTS and (4) TURN OFF BOTH LIGHTS.
Note: For the remote controller, replace
only with CR2032 battery. See bottom
of the remote controller for
replacement instruction.
CAUTION:Use only power adaptor that was
provided with this product. Using a different power
adaptor will damage the lights and cause fire, electrical
shock hazard.
CAUTION:Use only batteries of the same or
equivalent type as recommended. Remove all batteries
when replacing. Do not dispose of batteries in fire. Batteries
may explode or leak.Batteries are to be inserted with the
correct polarity.Exhausted batteries are to be removed from
the toy. The supply terminals are not to be short-circuited.
Do not dispose of this product as unsorted municipal waste.
Collection of such waste separately for special treatment is
necessary.
Operation
Turning on the tree
HOW TO USE THE DUAL COLOR LIGHT CONTROLLER
AND REMOTE CONTROL:
This tree package includes hinge pins, washers and bulbs
for any replacement or repair that you need to perform on
your tree. If extra parts are needed, contact the Customer
Service Team at 1-877-527-0313 between the hours of 8 am
and 5 pm EST, Monday through Friday.
Repairing Loose Hinges
Step 1. Place the branch into the slot of the bracket
Step 2. Insert a new hinge pin through the holes of the
bracket and secure with a washer.
Maintenance
Spare parts
1. Before using or reusing, inspect product carefully. Discard
any products that have cut, damaged or frayed wire
insulation or cords, cracks in the lampholders or enclo-
sures, loose connections, or exposed copper wire.
2.Before disassembling the tree, unplug the tree and remove
all ornaments and decorations.
3.Gently lift the tree top straight up to remove from the
center section and fold all branches towards the pole.
4.Repeat this step for the center and bottom tree sections.
5.When storing the product, carefully remove the product
from wherever it is placed, including tree,
branches, or bushes, to avoid any
undue strain or stress on the
product conductors, connections,
and wires. Cover the protective cap
on the poles to avoid damaging the
internal parts.
6.When not in use, store neatly in a cool, dry location
protected from sunlight.
Use and Care Instructions
Troubleshooting
User servicing instructions
Light
Controller
Selector
Button
Remote
Controller
Problem Solution
The tree does
not light
Ensure that all tree sections are
plugged into each other and that the
tree is plugged into the wall. If your
tree came with a foot pedal, step on
the On/Off button.
Check for blown fuses at the light string
and power cord plugs. Replace as
needed with the replacement fuses
provided.
Check for loose, broken, or missing
bulbs and replace as needed with the
replacement bulbs provided
Christmas Tree
Model: TG90P2082C01
Sku # 0000 000 000