Heater Sports Flop-Top Flex-A-Tee FTBT2499TT User manual

A Division of World Sports Products, Inc.
95 West 650 South · St. George, Utah 84770 · PH: 800-492-9334 · Fax: [phone]
www.HeaterSports.com · [e-mail] 1
INSTRUCTIONS
Model No. FTBT2499TT
Flop Top Flex-A-Tee
IMPORTANT - DO NOT RETURN THIS PRODUCT TO THE RETAIL STORE WHERE YOU
PURCHASED IT. IF YOU NEED ASSISTANCE OR PARTS PLEASE CALL TOLL FREE:
1-800-492-9334
WARNING
Improper use of this product can result in
serious injury. Read and follow these
instructions for proper and safe use of
the Flop Top Flex-A-Tee. Always wear a
helmet with a guard. Adult supervision
is required. Inspect the tee top, tee stem,
tripod base and adjustment knob before
each use for evidence of damage. Keep
the area clear in front of the tee and
around the swinging area of the batter.
CAUTION
Read all warnings and instructions in this
manual before using this equipment. Keep
this manual for future reference.
Part A - Top Tube with
Flex-A-Tee Top - Qty 1
Part B - Bottom
Tube with Height
Adjustment Knob -
Qty 1
Part D - Leg with
Rubber Tip - Qty 3
Part C - Plastic
Tripod Base -
Qty 1
The Only Travel Tee That Flops Away From Your Bat
& Resets With Every Hit

A Division of World Sports Products, Inc.
95 West 650 South · St. George, Utah 84770 · PH: 800-492-9334 · Fax: [phone]
www.HeaterSports.com · [e-mail] 2
Part D - Leg with Rubber Tip - Qty 3
Part B - Bottom
Tube with Height
Adjustment Knob - Qty 1
Part C - Plastic Tripod Base - Qty 1
Part A - Top Tube with
Flex-A-Tee Top - Qty 1
Part# E
Bolts - Qty 4
If You Are Missing Any Parts, Please Call Toll Free
1-800-492-9334
PART LIST - Model No. FTBT2499TT
Part# F
Flat Washer - Qty 7
Part# G
Lock Washer - Qty 4
Part# H
Acorn Nut - Qty 4

A Division of World Sports Products, Inc.
95 West 650 South · St. George, Utah 84770 · PH: 800-492-9334 · Fax: [phone]
www.HeaterSports.com · [e-mail] 3
HOW TO ASSEMBLE
Step 1 - Slide Part B (Bottom Tube with Height
Adjustment Knob) into the Top of Part C (Plastic
Tripod Base) and Align the Holes in Part B &
Part C.
Step 2 - Insert Part E (Bolt) through the Tripod,
then through the Pole. Add Part F (Flat Washer),
then Part G (Lock Washer), then Twist Part H (Acorn
Nut) into place on the end of the bolt & tighten.
Part #H
Part #E
Bolt #E
Flat Washer
#F Lock Washer
#G
Acorn Nut
#H
Part #GPart #F
Close-up View
Part B
Part C
Plastic Tripod Stand #C
Bottom Tube with Height
Adjustment Knob #B

A Division of World Sports Products, Inc.
95 West 650 South · St. George, Utah 84770 · PH: 800-492-9334 · Fax: [phone]
www.HeaterSports.com · [e-mail] 4
HOW TO ASSEMBLE (Cont.)
Step 3 - Slide Part D (Leg with Rubber Tip)
into Part C (Plastic Tripod Base) line up the
holes in Part C & Part D.
Step 4 - Slide Part F (Flat Washer) onto Part
E (Bolt). Slide Part E & F (Bolt with Flat Washer)
through the holes in Part C & Part D (Leg and
Plastic Tripod Stand). Slide Part F (Flat Washer),
then Part G (Lock Washer), then Twist Part H
(Acorn Nut) into Place and Tighten.
Step 5 - Slide Part A (Top Tube with Flex-A-Tee Top)
Into Part B (Bottom Tube & Tripod). Loosen or Tighten the
Height Adjustment Knob for desired Height.
How to Fold for Easy Storage -
Slide Part A (Top Tube with Flex-A-Tee Top) all the way into
Part B (Bottom Tube with Height Adjustment Knob), Tighten
Knob to Lock into Place. Lift Each Part D (Leg) out of the
Plastic Tripod and up to Part B (Bottom Tube
Height Adjustment Pole), Repeat
for each Leg for Quick & Easy Portability.
Part #H
Part #E
Part #G
Part #F Part #F
Acorn Nut
Part #H
Lock Washer
Part #G
Flat Washer
Part #F
Plastic Tripod Base
Part #C
Leg with Rubber
EndPart #D
Part #D
Part #C
Part #A
Part #B
Bolt
Part #E
Flat Washer
Part #F
Close-up View
Note: Repeat Step 3 & 4 Until All
Three Legs Are Assembled.