Heater Sports Slider Lite-Ball User manual

Read This Before Operating
IMPORTANT
DO NOT RETURN THE SLIDER MACHINE TO THE RETAIL STORE WHERE PURCHASED.
CALL TOLL FREE: [phone].
WARNING: ONLY USE SLIDER LITE-BALLS IN THE Slider MACHINE
The Slider Lite-Ball Pitching Machine only uses Slider Lite-Balls. If you put real baseballs the Slider Lite-Ball
Machine you will damage the machine and void the Slider warranty. Heater Sports recommends only using
official Slider Lite-Balls in your Slider Lite-Ball Pitching Machine. These balls are incredibly accurate, long last-
ing, and produce the best performance in the machine.
CUSTOMER SERVICE
HEATER SPORTS is dedicated to your customer satisfaction. If you experience any trouble with the operation
of the Slider Pitching Machine contact us at: [phone] or log on to www.HeaterSports.com.
WARNING: THIS PRODUCT IS TO BE USED BY ADULTS ONLY. MAKE SURE MACHINE IS TURNED OFF BEFORE
ASSEMBLY! KEEP HANDS AND ALL BODY PARTS AWAY FROM BALL ENTRY AND EXIT! SERIOUS HAND, EYE, AND
BODILY INJURY MAY OCCUR IF USED INCORRECTLY!
• Please be sure to read all of the instructions before using the Slider Lite-Ball
Pitching Machine to insure the machine is working properly.
• Parents: Your child should be made aware of the potential dangers of using the
Slider Lite-Ball Pitching Machine.
• Never put your fingers into the Slider Lite-Ball Pitching Machine.
• The Slider is not a toy and an adult should supervise children. It is very important
the batter makes sure the area is clear before swinging a bat.
• Stay clear of the ball opening while the Slider is operating. Although the balls are
very light, they may cause eye damage or other injury may occur.
Children must be advised of this danger and appropriate precautions should be taken.
• DO NOT use any type of ball other than Slider Lite-Balls in this machine.
• Always use a NOCSE approved batting helmet when batting.
• DO NOT LOOK INTO THE FRONT OF THE MACHINE WHILE THE SLIDER IS RUNNING.
Occasionally a ball may get stuck in the machine. The ball may pause and then shoot out and cause
eye injury. If the ball gets stuck, turn off the machine immediately. You should be able to remove the
ball easily by tilting the Slider backwards to eject the ball.
• Never operate in water or moisture.
• Always store in a dry area.

Model# SL129BB
Top Leg Assembly (Qty 3)
(A)
Bottom Leg Assembly (Qty 2)
Front
Leg Stakes (Qty 2)
(C)
Tri-Pod
Base (Qty 1)
(L)
Bolt (Qty 3) Nut (Qty 3)
(D)
(N)
(E)
Top Spiral (Qty 1)
(G)
Housing (Qty 1)
(K)
SLIDER PARTS LIST
STEP 1: Extend Part (B) until
push-pin locks.
STEP 2: Slide Part (B) into Part (A) and lock push-pin
into hole in Part (A).
STEP 5: Slide the leg assemblies
into the Tri-Pod Base (F) slots.
(A)
(C)
(F)
(B) (A)
(C)
(C)
Back Leg Assembly (Qty 1)
(B)
STEP 3: Extend Parts (C). STEP 4: Slide Part (C) into Part (A) and insert push-pin
into hole in Part (A) (2X).
Push-Pin holes
should be on the
backside.
STEP 6: Slide Part (D) (3X) through the
holes in the Tri-Pod Base (F)
slot holes and tighten nut (E) (3X).
(D)
(D)
(D)
(E)
(E) (E)
95 West 650 South • St. George, Utah 84770 • PH: 800-492-9334 • PH: 435-656-1756 • Fax: [phone]
Spiral Ball Feeder (Qty 1)
(M)
Teeth
Washer
(Qty1)
Metal
Washer
(Qty 1)
(I)
Knob
(Qty 1)
Carriage
Bolt
(Qty 1)
(F) (H) (J)
This slot is the
front of the base
Pitch
Height Adjustment
Slide the push-pin up
and down the back leg to
adjust the pitch height.
SLIDER ASSEMBLY

SLIDER ASSEMBLY (Continued)
(L)
(M)
STEP 9: Slide Spiral Ball
Feeder (M) on to Feeder Port
on Housing (K). Slide Top
Spiral (L) onto Feeder Port On
Spiral Ball Feeder (M). Plug
in Spiral Ball Feeder Cord into
Ball Feeder Outlet located on
the side of Housing (K).
(K)
Ball
Exit
Auto-Ball
Feeder
On/Off Switch
Fuse
Reset
Auto-Ball
Feeder Receptacle
Fitting
For
Batting
Cage
Fitting
For
Batting
Cage
Pitch
Height
Adjustment
Fast Ball &
Breaking
Ball Adjustment
Feeder
Fast Ball
& Breaking Ball
Pivot Knob
(K)
Mounting
Hole
(F)
STEP 7: Slide Housing (K)
onto Tri-Pod Base (F) and
align mounting hole of
Housing (K) and mounting
hole of Tri-Pod Base (F).
Housing (K) should
be assembled in back
of Tri-Pod Base (F).
(G) (I)
(H) (J)
STEP 8: Slide Carriage Bolt (J)
through mounting hole
in Tri-Pod Base (F) and
then through hole in
Housing (K). Then slide
Metal Washer (I) and Teeth Washer (H)
onto Carriage Bolt (J). Screw Knob (G)
onto Carriage Bolt (J) and tighten.
95 West 650 South • St. George, Utah 84770 • PH: 800-492-9334 • PH: 435-656-1756 • Fax: [phone]

WARNING!
ROTATING THE HEAD OF THE SLIDER FROM FAST BALL TO CURVE BALL POSITIONS CHANGES THE
DIRECTION AND TRAJECTORY OF THE PITCHED BALL. MAKE SURE NO PERSONS ARE IN FRONT OF
MACHINE WHILE ADJUSTING FOR FAST BALL OR CURVE BALL PITCHES.
Fast Ball/Curve Ball Instructions
Fast ball Position
CAUTION:
When machine is rotated for different pitch types, the ball direction changes dramatically.
Make sure no persons are in front of machine until machine is aimed properly
and pitching accurately at desired target.
Break Right Curve
Break Left Curve
Ball Pitch Adjustment: Loosen the
Ball Pitch Adjusment Knob where
the tripod head and machine hous-
ing connect. Tilt the housing right
or left for curve ball pitches.
95 West 650 South • St. George, Utah 84770 • PH: 800-492-9334 • PH: 435-656-1756 • Fax: [phone]
Ball Feeder Adjustment: Loosen
the Ball Feeder Knob to swivle the
ball feeder to an upright position
when pitching curve balls.
WARNING
When machine is pivoted for different pitch types, the pitch
direction can move left or right by up to 30 feet. Use extreme
caution when changing between pitch types. Never change
pitch types with any person in front of machine.

Front Leg
Stake
Front Leg
Stake
Front Leg Stakes
Slider Movement: The Slider may re-coil when
a ball is pitched. This may cause the Slider to
move slightly.
To stabilize the Slider, simply slide the hook of
one Front Leg Stake (N) (2X enclosed) over each
of the two front legs of the Slider and pound
each stake into the ground. This will stabilize
the movement of the Slider Lite-Ball Pitching
Machine and eliminate re-coil movement.
(N)
(N)
ADDENDUM
95 West 650 South • St. George, Utah 84770 • PH: 800-492-9334 • PH: 435-656-1756 • Fax: [phone]