Heritage Stamford PSFW071 User manual

Instaation
Guide
Please keep this booklet for future
reference.
Installer: When you have read these
instructions, please ensure you leave them
with the user.
Models Covered:
Basins tted to Pedestals and
Semi-Pedestals

2
INTRODUCTION
Thank you for buying a Heritage Product. When you buy a Heritage product, you can be condent
that it not only features a beautiful, distinctive, classic design, but that it has also been made to the
very highest quality standards.
To ensure that it works to its full potential, it needs to be tted correctly.
These tting instructions have been created to give you all of the information you need and, if you
need any further help, please do not hesitate to give us a call on: 0330 026 8503.
CONTENTS
SAFETY NOTES 3
INSTALLER GUIDELINES 4
TOOLS REQUIRED 4
INSTALLATION - PEDESTAL 5-7
INSTALLATION - SEMI PEDESTAL 8-10
CARING FOR YOUR PRODUCT 11
GUARANTEE 11
NEED HELP? 11

3
Please make sure you read these instructions and retain for future use.
All products manufactured by Heritage Bathrooms are safe, providing they are installed and used
correctly and also receive maintenance when needed.
Basins, including the connecting water and waste system need to be installed in accordance with and
meet the requirements of the Water Supply Regulations 1999 (Water Fittings) and current by-laws.
If you are in doubt about your ability to install this product correctly or safely, you should employ
the services of an experienced qualied plumber.
This product must not be modied in any way otherwise this will invalidate the guarantee.
Consider the following whilst using power tools:
• Prior to drilling into walls, check there are no hidden electrical cables or wires and
there are also no water pipes. These can potentially be found using an electrical or
metal detector. You may also need to know some of the schematics of previous
installations to determine the suitability and accommodation of the installation.
• Wear the correct PPE, especially ear, eye and hand protection
when using power tools. Unplug any mains equipment after use.
• Keep electrical equipment away from sources of water.
• If a blow-lamp is used when plumbing, the ame must be kept well away from
the product otherwise damage may occur.
Basins can be heavy; a lifting aid or second person at minimum will be required to measure and
manoeuvre safely. Ensure the wall the product is being tted to has enough reinforcement to
support the weight of the basin and pedestal.
SAFETY NOTES

4
INSTALLER GUIDELINES
Consider and plan the installation of your basin taps and waste whilst installing this basin.
They may have to be pre-tted before tting to the wall. Careful planning is also required to
ensure the waste and water supply pipes are contained within the connes of the pedestal.
Use wall xings suitable for your wall construction (not supplied). Plasterboard or stud walls can
be screwed directly into the timber frame, but may require specialist xings to secure the basin.
Appropriate wall plugs will need to be used for any masonary walls. Make sure to use a plastic or
rubber washer between the ceramic surface and the screw. Do not over-tighten wall xings, taps
or wastes to the basin as this may damage the ceramic surface.
Installing this product requires experience within plumbing. No responsibility will be taken for poor
workmanship resulting in leaks and injuries. Please ensure that the installation and accommodation is
designed with future serviceability of the product in mind. It is strongly advisable to t isolation valves
before the water xtures in case isolation is required at any point during maintenance.
Failure to observe crucial information in these tting instructions will nullify your guarantee.
In the event a future claim is made under the product warranty, compensation costs may be
affected if the ability to service the product has not been considered in the original design.
Please Note: Your semi-pedestal is not a load-bearing xture after installation.
Make sure the appropriate xings are used to secure the basin to ensure the weight is supported.

5
INSTALLATION - PEDESTAL
3 4
12
Place the basin on the pedestal and move
to the required position in your bathroom.
Ensure the basin is correctly positioned
on the pedestal, the basin and pedestal
are level, and the back of the basin is in
full contact with the wall.
Mark the centre of the basin on the wall.
Make a horizontal line along the back edge
of the basin and trace along the outer
edge of the pedestal. Mark the position of the
bolt/screw holes on the basin and pedestal.
Remove the basin. Draw a horizontal line
through the bolt/screw holes and carry
the centre line down until it meets the
bolt/screw holes on the basin.
Refer to your tap and waste instructions to
install these on to the basin, including the waste
trap. Place the basin back on to the pedestal
and mark on the wall the locations of the waste
pipework and the hot and cold connections.

6
INSTALLATION - PEDESTAL
Drill each xing hole, taking into account
the screws and wall plugs (not supplied).
Install the threaded bolts if bolt xings
are supplied. If necessary, also drill the
holes required for any pipework.
7 8
56
Loosely secure the
pedestal to the oor
using appropriate
xings for your
oor type.
DO NOT
OVERTIGHTEN.
Locate the basin back on to the
pedestal, hold in place.
Plumb
the water
and waste
pipework.

7
INSTALLATION - PEDESTAL
10
9Using Bolt Fixings Using Screw Fixings
Secure the basin with nuts and washers.
11 Connect your water and waste
pipework. Turn on the water supply at
the isolation valve and check for leaks.
Secure the basin to the wall using
appropriate xings for the wall type
that can support the weight
of the basin.
17mm
12
Use a suitable silicon sealant around the
back of the basin to keep watertight.

8
INSTALLATION - SEMI PEDESTAL
3 4
12
Place the basin in the desired location in your
bathroom. Ensure the basin is level, and the
back of the basin is in full contact with the wall.
Using a pencil, mark the centre of the basin
on its tap ledge, extend this line up where it
meets the wall. Make a horizontal line along
the back edge of the basin and trace
along the bottom of the basin.
Refer to your tap and waste instructions to
install these on to the basin, including the
waste trap. Place the basin back in its position
and mark on the wall the locations of the waste
pipework and the hot and cold connections.
Place your semi-pedestal in position.
Trace around the outer edge and mark the
position of the xing holes. Measure the
internal width of the ceramic at the back of
the pedestal and add the inner line to mark
the Pedestal Plumbing Area. Make sure your
waste and water connections are in this area.
Measure on the basin:
• the vertical distance from the centre tap
ledge to the centres of the xing holes
• the distance from the centre line to the
centres of each xing hole.
Transfer these measurements on to the
wall using the bottom centre of the
inverted ‘T’ as a starting point.

9
INSTALLATION - SEMI PEDESTAL
Drill each xing hole for the basin and pedestal,
taking into account the screws and wall plugs
(not supplied). Install the threaded bolts if bolt
xings are supplied. If necessary, also drill the
holes required for any pipework.
7 8
56Using Bolt Fixings
Using Screw Fixings
Locate the basin on to the threaded bolts.
Ensure the basin is level and secure
with nuts and washers.
Locate the basin on to the threaded
bolts. Ensure the basin is level and secure
the basin to the wall using suitable xings
to support the weight of the basin.
Plumb the water and waste
pipework and connect to your
waste and tap xings.
17mm
10mm

10
INSTALLATION - SEMI PEDESTAL
Place the
semi-pedestal
in position.
Using the
appropriate xings
for your wall type,
fully secure the
pedestal to
the wall.
12
11 Using Fixing Brackets
Using Screw Fixings
Use a suitable silicon sealant
around the back of the basin
and around the edge of the
pedestal to keep watertight.
Turn on the water supply at the isolation
valve and check for leaks.
910
Refer to the instructions on
the xings pack to install
the xing brackets.
Put the semi-pedestal in
position and secure using
screws and caps.

11
Heritage products are made from premium materials, with hand polishing and
electroplated nishes.
Your product should be regularly cleaned with warm water, a mild pH-neutral liquid soap, and
polished with a soft cloth. Any residues from soap, toiletries etc. should be rinsed off straight after
use.
Household bleaches and cleaners contain harsh chemicals and may damage the surface nish.
Avoid using abrasive cloths, scouring pads, scrub sponges, steel wool or anything similar.
The condence we have in the quality of our products and services enables us to offer a free
peace-of-mind product guarantee from 2 years up to a lifetime guarantee against any manufacturing
faults, with proof of purchase. In addition, our attentive customer service team are available to
help solve any problems which may arise quickly and effectively so you can enjoy your bathroom.
To see the specic guarantee for this product, scan the QR Code
or visit the following URL:
https://www.heritagebathrooms.com/service-centre/guarantee
In the unlikely event that you encounter a problem with your Heritage product, you must, in the
rst instance, contact the retailer you purchased it from. They will advise as to whether it is due
to a manufacturing fault or an installation fault. If the problem is due to a manufacturing fault, they
will contact us to arrange a supply of a replacement product as soon as possible. To speak to a
Heritage customer service advisor, please contact our technical helpline on 0330 026 8503.
NEED HELP?
GUARANTEE
CARING FOR YOUR PRODUCT

We love to see how Heritage products are used so please keep in
touch and share pictures of your new bathroom with us.
If you have any queries, our dedicated customer service teams and products experts
are available to help.
Email us [e-mail] Call us 0330 026 8503 Website www.heritagebathrooms.com
@heritagebathrooms
UK: Heritage Bathrooms, Pooley Hall Drive, Birch Coppice Business Park, Dordon, Tamworth B78 1SG
EU: Masco Europe S.à.r.l., 14 Rue Strachen, 6933 Mensdorf, Luxembourg.
D6 - BAS PED-SEMIPED