Plumbline Progetto Minimo Series User manual

INSTALLATION
BASIN MIXERS
-Screw and tighten feed pipes (1)
-Threaded tie rod (2)
-Insert base flange (4) gasket (5), then place the mixer on the
basin/bidet deck
-Insert gasket (6) and clamp (7)
-Tighten nut (10) using a12mm spanner
-Connect pipes (1) to water supply
NOTE:
-Unscrew the aerator with 22 mm spanner
-Immerse for half a day in the water-vinegar solution (80-20%)
-Wash, then reassemble SPARE PARTS CODE
F81/2
180
Min 45
Max 75
G 1/2"
240 x 100
62
Ch.9
350
Max 35
ø 35
G 3/8”
ø48
Max 180
G 1"1/4
ø 63
Min 35
Max 50
115
10°
92
143
Min 45 - Max 75
G 1/2"
G 3/4"
G 1/2"
115
100 x 165
G 1/2"
G 1/2"
Min 45
Max 75
100 x 100
Ch.36
340
Max 45
ø 35
G 3/8”
ø48
180
250
303
M002 / M002ES
M007
M033
M034
M006
WARRANTY :
MAINTENANCE
- Unscrew dowel (2) using thespanner supplied (3).
- Unscrew cap (5)
- Unscrew the blocking nut (6) using a 24 mm spanner.
-. Replace cartridge (7).
- To remount the blocking nut (6) use a 0,8 Kgm max. dynamometric spanner to fasten.
- To remount the whole handle, follow the procedure reversed.
AERATOR MAINTENANCE
31
2
4
5
6
7
WARNINGS
-The plumbing installation should be fitted with adequate water filters and pressure regulation devices inorder to avoid misfunctioning in case of pressure shocks
-Advised pressure is between 3 and 5 bars
-Flush pipelines thoroughly before installing mixers
-Clean the mixers with soap mixed with water; products mustbe dried with a soft cloth in order to prevent limescale deposits
-Limescale deposits or other impurities infilters of flow guides mustbe removed monthly by using appropriate products or by immersing in water/vinegar solution
(80/20)
-For eachmixer installation, please follow instructions incorresponding page
ARTICLES SPARE PARTS CODES
M002
M002ES
M006
M007
M033
M034
K27/2
K27
K25
1
2
10
4
6
7
5
CARTRIDGE REPLCEMENT
T 04 568 9898 E [email protected] www.plumbline.co.nz
Distributed by:
INSTALLATION INSTRUCTIONS
MINIMO BASIN MIXER | M002
MINIMO BASIN MIXER WITH ENERGY SAVER | M002ES
MINIMO VESSEL BASIN MIXER | M006
MINIMO SQUARE WALL MOUNT MIXER | M007
MINIMO SHOWER MIXER | M033
MINIMO DIVERTER MIXER | M034

SHOWER/DIVERTER MIXERS
WALL MOUNT MIXERS
M007
2
3
4
1
MIN
MAX
PLATTENBELAGESGRENZEN N
AVVERTENZE
ADVICE
Hot
water
Cold
water
Cold
Hot
-When installing the concealed part of the mixer, please observe the given centre-to-
wall distances shown on the drawing and printed on the mixer protecting cover.
-Remove protecting cover and insert flange
-Install handle following the 'handle installation' instructions on the page aside.
DIVERTER REPLACEMENT
-Remove handle. Remove cover plate (1).
-Push knob (2) against seat. Without releasing pressure, unscrew knob
-Unscrew diverter (3) using a 19 mm spanner
-We recommend to replace the entire diverter unit and not separate components
-Install mixer body paying attention to the min/max wall lining distance given on the
sticker
-Block spout (1) on the flange wall with screws (2).
-Remove the protective cover.
-Insert the flange with his spout, paying attention to the seals (3).
-Tighten the screw (4) on the spout.
-Install handle.
12
3

SHOWER/DIVERTER MIXERS
WALL MOUNT MIXERS
M007
2
3
4
1
MIN
MAX
PLATTENBELAGESGRENZEN N
AVVERTENZE
ADVICE
Hot
water
Cold
water
Cold
Hot
-When installing the concealed part of the mixer, please observe the given centre-to-
wall distances shown on the drawing and printed on the mixer protecting cover.
-Remove protecting cover and insert flange
-Install handle following the 'handle installation' instructions on the page aside.
DIVERTER REPLACEMENT
-Remove handle. Remove cover plate (1).
-Push knob (2) against seat. Without releasing pressure, unscrew knob
-Unscrew diverter (3) using a 19 mm spanner
-We recommend to replace the entire diverter unit and not separate components
-Install mixer body paying attention to the min/max wall lining distance given on the
sticker
-Block spout (1) on the flange wall with screws (2).
-Remove the protective cover.
-Insert the flange with his spout, paying attention to the seals (3).
-Tighten the screw (4) on the spout.
-Install handle.
12
3

INSTALLATION
BASIN MIXERS
-Screw and tighten feed pipes (1)
-Threaded tie rod (2)
-Insert base flange (4) gasket (5), then place the mixer on the
basin/bidet deck
-Insert gasket (6) and clamp (7)
-Tighten nut (10) using a12mm spanner
-Connect pipes (1) to water supply
NOTE:
-Unscrew the aerator with 22 mm spanner
-Immerse for half a day in the water-vinegar solution (80-20%)
-Wash, then reassemble SPARE PARTS CODE
F81/2
180
Min 45
Max 75
G 1/2"
240 x 100
62
Ch.9
350
Max 35
ø 35
G 3/8”
ø48
Max 180
G 1"1/4
ø 63
Min 35
Max 50
115
10°
92
143
Min 45 - Max 75
G 1/2"
G 3/4"
G 1/2"
115
100 x 165
G 1/2"
G 1/2"
Min 45
Max 75
100 x 100
Ch.36
340
Max 45
ø 35
G 3/8”
ø48
180
250
303
M002 / M002ES
M007
M033
M034
M006
WARRANTY :
MAINTENANCE
- Unscrew dowel (2) using thespanner supplied (3).
- Unscrew cap (5)
- Unscrew the blocking nut (6) using a 24 mm spanner.
-. Replace cartridge (7).
- To remount the blocking nut (6) use a 0,8 Kgm max. dynamometric spanner to fasten.
- To remount the whole handle, follow the procedure reversed.
AERATOR MAINTENANCE
31
2
4
5
6
7
WARNINGS
-The plumbing installation should be fitted with adequate water filters and pressure regulation devices inorder to avoid misfunctioning in case of pressure shocks
-Advised pressure is between 3 and 5 bars
-Flush pipelines thoroughly before installing mixers
-Clean the mixers with soap mixed with water; products mustbe dried with a soft cloth in order to prevent limescale deposits
-Limescale deposits or other impurities infilters of flow guides mustbe removed monthly by using appropriate products or by immersing in water/vinegar solution
(80/20)
-For eachmixer installation, please follow instructions incorresponding page
ARTICLES SPARE PARTS CODES
M002
M002ES
M006
M007
M033
M034
K27/2
K27
K25
1
2
10
4
6
7
5
CARTRIDGE REPLCEMENT