Hi-flying HF-A11 User manual
HF-A11 Embedded WiFi Module User Manual
Shanghai High-Flying Electronics Technology Co., Ltd
www.hi-flying.com 1
HF-A11
Embedded WiFi Module User Manual
V4.3
Overview of Characteristic
Support IEEE802.11b/g/n Wireless Standards
Support TCP/IP/UDP Network Protocols
Support UART/GPIO/Ethernet Data Interface
Support Work As STA/AP/AP+STA Mode
Support Router/Bridge Mode Networking
Support Internal/External Antenna Option
Support Max TCP links: 32
Support AT+ Instruction Set for Configuration
Support Friendly Web Configuration Page
Support Palmodic Signal
Support UART Free/Auto-Frame Function
Support Smart Link Application Tools
Single +3.3V Power Supply
Small Size: 25 x 40mm
FCC/CE Certificated
Flexible Software Platform with Linux OS
High-Flying
HF-A11 Embedded WiFi Module User Manual
Shanghai High-Flying Electronics Technology Co., Ltd
www.hi-flying.com 2
TABLE OF CONTENTS
1.PRODUCT OVERVIEW ............................................................................................................... 7
1.1.General Specification ............................................................................................................. 7
1.2.Hardware Introduction............................................................................................................ 8
1.2.1.Pins Definition.................................................................................................................... 8
1.2.2.Mechanical Size.................................................................................................................9
1.2.3.On-board Chip Antenna................................................................................................... 10
1.2.4.External Antenna ............................................................................................................. 10
1.2.5.Evaluation Kit................................................................................................................... 11
1.2.6.Order Information............................................................................................................. 12
1.3.Hardware Reference Design................................................................................................ 13
1.3.1.Hardware Typical Application.......................................................................................... 13
1.3.2.10/100M Ethernet Interface............................................................................................. 13
1.3.2.1.Ethernet Connection with Transformer........................................................................ 14
1.3.2.2.Ethernet Connection without Transformer................................................................... 14
1.3.3.UART Interface................................................................................................................ 14
1.3.4.Power Interface................................................................................................................ 15
1.4.Software Reference Design ................................................................................................. 16
1.4.1.Transparent Transmission Mode..................................................................................... 16
1.4.2.Configuration Mode ......................................................................................................... 16
1.4.3.Multi-TCP Link Connection.............................................................................................. 17
1.4.4.TCPB Function................................................................................................................. 17
1.4.5.GPIO Function................................................................................................................. 17
1.4.6.Palmodic Signal............................................................................................................... 18
2.FUNCTIONAL DESCRIPTION ................................................................................................. 19
2.1.Wireless Networking.............................................................................................................19
2.1.1.Basic Wireless Network Based On AP (Infrastructure)................................................... 19
2.1.2.Wireless Network Based On Adhoc Network (Adhoc) .................................................... 20
2.1.3.Wireless Network Based On AP+STA............................................................................. 20
2.2.Auto- Frequency Function ................................................................................................... 21
2.3.Security.................................................................................................................................. 21
2.4.UART Frame Scheme ........................................................................................................... 22
2.4.1.UART Free-Frame........................................................................................................... 22
2.4.2.UART Auto-Frame........................................................................................................... 22
2.5.Address Binding ................................................................................................................... 22
2.6.Ethernet Interface Communication..................................................................................... 23
2.6.1.HF-A11 Ethernet Interface Networking (As AP).............................................................. 23
2.6.2.HF-A11 Ethernet Interface Networking (As STA, N-Ver) ................................................ 23
2.6.3.HF-A11 Ethernet Interface Networking (As STA, Z-Ver)................................................. 24
2.7.Search Function for STA...................................................................................................... 24
2.8.Work Mode............................................................................................................................. 24
2.9.Network Protocol.................................................................................................................. 25
2.10.Parameters Configuration ................................................................................................ 25
2.11.Firmware Upgrade............................................................................................................. 25
2.12.GPIO Function ...................................................................................................................25
3.OPERATION GUIDELINE ......................................................................................................... 26
3.1.Configuration via Web Accessing....................................................................................... 26
3.1.1.Open Web Management Interface .................................................................................. 26
High-Flying
HF-A11 Embedded WiFi Module User Manual
Shanghai High-Flying Electronics Technology Co., Ltd
www.hi-flying.com 3
3.1.2.Mode Selection Page....................................................................................................... 26
3.1.3.AP Interface Setting Page ............................................................................................... 27
3.1.4.STA Interface Setting Page ............................................................................................. 27
3.1.5.Application Setting Page.................................................................................................. 28
3.1.6.Device Management Page .............................................................................................. 29
3.2.HF-A11 Usage Introduction.................................................................................................. 29
3.2.1.Software Debug Tools ..................................................................................................... 29
3.2.2.Network Connection ........................................................................................................ 30
3.2.3.Module Debug.................................................................................................................. 30
3.3.Typical Application Examples ............................................................................................. 32
3.3.1.Wireless Control Application............................................................................................ 32
3.3.2.Remote Management Application ................................................................................... 33
3.3.3.Transparent Serial Port Application................................................................................. 33
3.3.4.Wireless Data Acquisition Card Application .................................................................... 34
4.AT+INSTRUCTION INTRODUCTION...................................................................................... 35
4.1.Configuration Mode..............................................................................................................35
4.1.1.Switch to Configuration Mode.......................................................................................... 35
4.2.AT+ Instruction Set Overview.............................................................................................. 36
4.2.1.Instruction Syntax Format................................................................................................ 36
4.2.2.AT+ Instruction Set.......................................................................................................... 37
4.2.2.1.AT+E ............................................................................................................................38
4.2.2.2.AT+ENTM .................................................................................................................... 38
4.2.2.3.AT+NETP..................................................................................................................... 38
4.2.2.4.AT+UART..................................................................................................................... 39
4.2.2.5.AT+ UARTF.................................................................................................................. 39
4.2.2.6.AT+ UARTFT ............................................................................................................... 39
4.2.2.7.AT+ UARTFL................................................................................................................ 40
4.2.2.8.AT+TMODE.................................................................................................................. 40
4.2.2.9.AT+WMODE ................................................................................................................ 40
4.2.2.10.AT+WSKEY.............................................................................................................. 40
4.2.2.11.AT+WSSSID............................................................................................................. 41
4.2.2.12.AT+ WSLK................................................................................................................ 41
4.2.2.13.AT+WEBU ................................................................................................................ 41
4.2.2.14.AT+WAP................................................................................................................... 42
4.2.2.15.AT+WAKEY.............................................................................................................. 42
4.2.2.16.AT+HIDESSID.......................................................................................................... 43
4.2.2.17.AT+MSLP ................................................................................................................. 43
4.2.2.18.AT+WSCAN.............................................................................................................. 43
4.2.2.19.AT+ TCPLK .............................................................................................................. 43
4.2.2.20.AT + TCPDIS............................................................................................................ 44
4.2.2.21.AT+ WANN............................................................................................................... 44
4.2.2.22.AT+ LANN ................................................................................................................ 44
4.2.2.23.AT + DHCPDEN....................................................................................................... 44
4.2.2.24.AT+ DHCPGW.......................................................................................................... 45
4.2.2.25.AT+ TCPTO.............................................................................................................. 45
4.2.2.26.AT+ MAXSK ............................................................................................................. 45
4.2.2.27.AT+TCPB ................................................................................................................. 45
4.2.2.28.AT+TCPPTB............................................................................................................. 46
4.2.2.29.AT+TCPADDB.......................................................................................................... 46
High-Flying
HF-A11 Embedded WiFi Module User Manual
Shanghai High-Flying Electronics Technology Co., Ltd
www.hi-flying.com 4
4.2.2.30.AT+TCPTOB ............................................................................................................ 46
4.2.2.31.AT+TCPLKB............................................................................................................. 46
4.2.2.32.AT+EPHY ................................................................................................................. 47
4.2.2.33.AT+STTC.................................................................................................................. 47
4.2.2.34.AT+DOMAIN............................................................................................................. 47
4.2.2.35.AT+FRLDEN............................................................................................................. 47
4.2.2.36.AT+RELD ................................................................................................................. 48
4.2.2.37.AT+Z......................................................................................................................... 48
4.2.2.38.AT+MID..................................................................................................................... 48
4.2.2.39.AT+VER.................................................................................................................... 48
4.2.2.40.AT+H......................................................................................................................... 48
5.PACKAGE INFORMATION ....................................................................................................... 49
5.1Shipping Information............................................................................................................49
APPENDIX A: QUESTIONS AND ANSWERS ............................................................................... 50
Q1: How to configure transparent serial port application (TCP protocol) with two HF-A11
modules?.......................................................................................................................................... 50
Q2: Where to Set HF-A11 Module LAN IP and WAN IP through Web Page？........................... 50
Q3: How to configure transparent serial port application (UDP protocol) with two HF-
A11 modules?.................................................................................................................................. 51
Q4: Where to set HF-A11 module network protocol (TCP/UDP)?.............................................. 51
Q5: How to configure transparent serial port application: Two HF-A11 modules all
configured as STA and connection through AP?........................................................................ 52
Q6: How to avoid IP address confliction when apply HF-A11 module?.................................... 53
Q7: PC works as server, all HF-A11 modules works as data acquisition card and
connect with PC, how to configure this application? ................................................................. 53
APPENDIX B: EVB REFERENCE DESIGN ................................................................................... 55
APPENDIX C: EXTERNAL POWER SHUTDOWN MODE REFERENCE DESIGN.................. 56
APPENDIX D: USER DEVICE PSEUDO-CODE REFERENCE FOR AGREEMENT
TRANSMITION MODE ....................................................................................................................... 57
APPENDIX E: CONTACT INFORMATION ..................................................................................... 59
High-Flying
HF-A11 Embedded WiFi Module User Manual
Shanghai High-Flying Electronics Technology Co., Ltd
www.hi-flying.com 5
LIST OF FIGURES
Figure 1.HF-A11 Demo.................................................................................................................... 8
Figure 2.HF-A11 Pins Map............................................................................................................... 8
Figure 3.HF-A11 Mechanical Dimension......................................................................................... 9
Figure 4.HF-A11 Chip Antenna Keep Out Region......................................................................... 10
Figure 5.Suggested Module Placement Region............................................................................ 10
Figure 6.HF-A11 Evaluation Kit ..................................................................................................... 11
Figure 7.HF-A11 Order Information............................................................................................... 12
Figure 8.HF-A11 Hardware Typical Application............................................................................. 13
Figure 9.Ethernet Reference Design with Transformer................................................................. 14
Figure 10.Ethernet Reference Design without Transformer............................................................ 14
Figure 11.UART Interface Reference Design.................................................................................. 15
Figure 12.User MCU Software Flow Chart ...................................................................................... 16
Figure 13.Multi-TCP Link Data Transmition Structure..................................................................... 17
Figure 14.HF-A11 Functional Architecture ...................................................................................... 19
Figure 15.HF-A11 Basic Wireless Network Structure...................................................................... 19
Figure 16.HF-A11 Adhoc Network Structure ................................................................................... 20
Figure 17.HF-A11 AP+STA Network Structure................................................................................ 21
Figure 18.HF-A11 Ethernet Interface Networking (As AP).............................................................. 23
Figure 19.HF-A11 Ethernet Interface Networking (As STA, N-Ver) ................................................ 23
Figure 20.HF-A11 Ethernet Interface Networking (As STA, Z-Ver)................................................. 24
Figure 21.HF-A11 Transparent Transmission Demo....................................................................... 25
Figure 22.Open Web Management page......................................................................................... 26
Figure 23.Mode Selection Page....................................................................................................... 27
Figure 24.AP Interface Setting Page ............................................................................................... 27
Figure 25.STA Interface Setting Page ............................................................................................. 28
Figure 26.Application Setting Page.................................................................................................. 28
Figure 27.Device Management Page .............................................................................................. 29
Figure 28.STA Interface Debug Connection.................................................................................... 30
Figure 29.AP Interface Debug Connection...................................................................................... 30
Figure 30.“CommTools” Serial Debug Tools................................................................................... 30
Figure 31.“TCPUDPDbg” Tools Create Connection........................................................................ 31
Figure 32.“TCPUDPDbg” Tools Setting........................................................................................... 31
Figure 33.“TCPUDPDbg” Tools Connection.................................................................................... 32
Figure 34.Wireless Control Application............................................................................................ 32
Figure 35.Remote Management Application ................................................................................... 33
Figure 36.Transparent Serial Port Application................................................................................. 33
Figure 37.Wireless Data Acquisition Card Application .................................................................... 34
Figure 38.HF-A11 Default UART Port Parameters.......................................................................... 35
Figure 39.Switch to Configuration Mode.......................................................................................... 35
Figure 40.”AT+H” Instruction for Help.............................................................................................. 36
Figure 41.Shipping Information........................................................................................................ 49
Figure 42.Configure Transparent Serial Port Connection (TCP)..................................................... 50
Figure 43.Module LAN IP Setting .................................................................................................... 50
Figure 44.Module WAN IP Setting................................................................................................... 51
Figure 45.Configure Transparent Serial Port Connection (UDP) .................................................... 51
Figure 46.Module Network Protocols: TCP/Server.......................................................................... 52
Figure 47.Module Network Protocol: TCP/Client............................................................................. 52
High-Flying
HF-A11 Embedded WiFi Module User Manual
Shanghai High-Flying Electronics Technology Co., Ltd
www.hi-flying.com 6
Figure 48.Module Network Protocol: UDP....................................................................................... 52
Figure 49.Two HF-A11 Modules Connection Through AP .............................................................. 53
Figure 50.Wireless Data Acquisition Card Setting........................................................................... 54
LIST OF TABLES
Table 1 HF-A11 Module Technical Specifications ..............................................................................7
Table 2 HF-A11 Pins Definition........................................................................................................... 8
Table 3 HF-A11 External Antenna Parameters................................................................................. 11
Table 4 HF-A11 Evaluation Kit Interface Description........................................................................ 12
Table 5 HF-A11 Web Access Default Setting...................................................................................26
Table 6 Error Code DescribtionHF-A11 Web Access Default Setting.............................................. 37
Table 7 AT+ Instruction Set List........................................................................................................ 37
HISTORY
Ed. V3.1 Created on 1-14-2012.
Ed. V4.0 Update AT command information on 6-25-2012.
Ed. V4.1 Update 2.1.3 AP+STA function notes and command setting;
Add 1.2.3 On-board Chip Antenna;
Update Appendix B, C on 10-15-2012.
Ed. V4.2 Update EVB reference design and picture.
Ed. V4.3 Update on 4-24-2013
Remove agreement transmission mode function support
Remove WDS function support
Add AT command，AT+DOMAIN，AT+FRLDEN，AT+DHCPDEN，AT+HIDESSID
High-Flying
HF-A11 Embedded WiFi Module User Manual
Shanghai High-Flying Electronics Technology Co., Ltd
www.hi-flying.com 7
1.PRODUCT OVERVIEW
1.1. General Specification
Table 1 HF-A11 Module Technical Specifications
Class Item Parameters
Certification FCC/CE
Wireless standard 802.11 b/g/n
Frequency range 2.412GHz-2.484GHz
802.11b: +20 dBm (Max.)
802.11g: +18 dBm (Max.)
802.11n: +15 dBm (Max.)
Transmit Power
Configurable
802.11b: -89 dBm
802.11g: -81dBm
Receiver Sensitivity 802.11n: -71dBm
External:I-PEX Connector
Wireless
Parameters
Antenna Option Internal:On-board chip antenna
UART: 1200bps - 230400bps
GPIOs
Data Interface Ethernet: 100Mpbs
Operating Voltage 3.3V (+/-5%)
Operating Current 170mA~300mA
Operating
Temperature -40℃- 85℃
Storage Temperature -45℃- 125℃
Hardware
Parameters
Dimensions and Size 25×40×8mm
Network Type STA /AP/AP+STA mode
Security Mechanisms WEP/WPA-PSK/WPA2-PSK/WAPI
Encryption WEP64/WEP128/TKIP/AES
Work Mode Transparent Transmission and
Serial command AT+instruction set
Network Protocol TCP/UDP/ARP/ICMP/DHCP/DNS/HTT
P
Max. TCP Connection 32
User Configuration Web Server＋AT command config.
Software
Parameters
User Application SW Support customized application SW
Provide SDK package
Provide smart link tools
High-Flying
HF-A11 Embedded WiFi Module User Manual
Shanghai High-Flying Electronics Technology Co., Ltd
www.hi-flying.com 8
1.2. Hardware Introduction
Figure 1. HF-A11 Demo
1.2.1. Pins Definition
Figure 2. HF-A11 Pins Map
Table 2 HF-A11 Pins Definition
Pin Description Name Direction Note
1 Ground GND Power
2 VCC 3.3V Power 3.3V @ 350mA power input
UART Data Transmit UART_TXD O
3 GPIO GPIO3 I/O
UART Data Receive UART_RXD I
4 GPIO GPIO4 I/O
UART sends request of
data transmission UART_RTS O
5
GPIO GPIO5 I/O
UART receives data
transmission permission UART_CTS I
6
GPIO GPIO6 I/O
If not use UART function，this
4 pins can be configured as
GPIO pins, and can change
GPIO pin status through AT
command
7 Module reset signal RESET I “Low ( 0 )” effective reset input.
The reset duration should be
kept more than 300ms
High-Flying
HF-A11 Embedded WiFi Module User Manual
Shanghai High-Flying Electronics Technology Co., Ltd
www.hi-flying.com 9
WiFi status Indication nLink O
8 GPIO GPIO8 I/O
“1”- WIFI connection available,
“0”- No WIFI connection
Can be configured as GPIO.
Indicate the module
status of power on
process
nReady O
9
GPIO GPIO9 I/O
“0” or “Palmodic Signal” - Finish
module boot up process;
“1” - Module boot up not finish.
Can be configured as GPIO.
Restore configuration nReload I
10 GPIO GPIO10 I/O
Module will Restore factory
default configuration after set
this pin “0” more than 3s, then
set “1”.
11 Ethernet Interface PHY_RX+ I
12 Ethernet Interface PHY_RX- I
13 Ethernet Interface PHY_TX+ O
14 Ethernet Interface PHY_TX- O
+1.8V Ethernet Data Interface
Support transformer and direct
connection (AC couple) mode.
1.2.2. Mechanical Size
HF-A11 modules physical size as follows:
Figure 3. HF-A11 Mechanical Dimension
High-Flying
HF-A11 Embedded WiFi Module User Manual
Shanghai High-Flying Electronics Technology Co., Ltd
www.hi-flying.com 10
1.2.3. On-board Chip Antenna
HF-A11 module support internal ob-board chip antenna option. When costomer select internal
antenna, you shall comply with following antenna design rules and module location suggestions:
¾For customer PCB, RED color region (6x8mm) can’t put componet or paste GND net;
¾Antenna must away from metal or high components at least 10mm;
¾Antenna can’t be shieldedby any meal enclosure; All cover, include plastic, shall away
from antenna at least 10mm;
Figure 4. HF-A11 Chip Antenna Keep Out Region
High-Flying suggest HF-A11 module better locate in following region at customer board, which to
reduce the effect to antenna and wireless signal, and better consult High-Flying technical people
when you structure your module placement and PCB layout.
Figure 5. Suggested Module Placement Region
1.2.4. External Antenna
HF-A11 modules support internal antenna and external antenna option for user dedicated
application. If user select external antenna, HF-A11 modules must be connected to the 2.4G
antenna according to IEEE 802.11b/g/n standards.
The antenna parameters required as follows:
High-Flying
HF-A11 Embedded WiFi Module User Manual
Shanghai High-Flying Electronics Technology Co., Ltd
www.hi-flying.com 11
Table 3 HF-A11 External Antenna Parameters
1.2.5. Evaluation Kit
High-Flying provides the evaluation kit to promote user to familiar the product and develop the
detailed application. The evaluation kit shown as below, user can connect to HF-A11 module with
the RS-232 UART port, 100M Eth port or Wireless port to configure the parameters, manage the
module or do the some functional tests.
Figure 6. HF-A11 Evaluation Kit
The external interface description for evaluation kit as follows:
Item Parameters
Frequency range 2.4~2.5GHz
Impedance 50 Ohm
VSWR 2 (Max)
Return Loss -10dB (Max)
Connector Type I-PEX or populate directly
High-Flying
HF-A11 Embedded WiFi Module User Manual
Shanghai High-Flying Electronics Technology Co., Ltd
www.hi-flying.com 12
Table 4 HF-A11 Evaluation Kit Interface Description
1.2.6. Order Information
Base on customer detailed requirement, HF-A11 series modules provide different variants and
physical type for detailed application.
Figure 7. HF-A11 Order Information
Function Name Description
DC jack 5~18V power input connector
3-Pin 3-Pin RS485 interface
DB9 Male serial jack of 9-pin,and used to connect to PC
RJ-45 100M Eth Interface
External
Interface
Module 2x7 2mm DIP connector
Power (Red) 3.3V Power Indicator
TXD TXD Indicator
RXD RXD Indicator
Ready nReady/GPIO Indicator
LED
Link nLink/GPIO Indicator
Reset Used to reset the module.
Button Reload Module restore to factory default configuration.
High-Flying
HF-A11 Embedded WiFi Module User Manual
Shanghai High-Flying Electronics Technology Co., Ltd
www.hi-flying.com 13
1.3. Hardware Reference Design
1.3.1. Hardware Typical Application
Figure 8. HF-A11 Hardware Typical Application
Notes：
nRST- Module hardware reset signal. Input. Logics “0” effective.
There is 100K Ohm pull-up resister internal. When module power up or some issue happened,
MCU need assert nRST signal “0” at least 300ms, then set” 1” to keep module fully reset.
nReady- Module boot up ready signal. Output. Logics “0” effective.
There is 4.7K Ohm pull-up resister internal. The module will output “0” “or “Palmodic Signal” after
normal boot up. This signal used to judge if module finish boot up and ready for application or
working at normal mode.
nLink- Module WIFI connection indication. Output.
There is 4.7K Ohm pull-up resister internal. When module connect to AP (STA mode) or some
WiFi STA connect to module (AP mode), the module will output “0”. This signal used to judge if
module already at WiFi connection status.
nReload- Module restore to factory default configuration.Input. Logics “0” effective.
User can assert nReload signal “0” more than 3’s through button or MCU pin, then release,
module will restore to factory default configuration and re-start boot up process. User need add
4.7K~10K Ohm pull-up resister external the module. If not use this function, then can use AT
command AT+FRLDEN=off to disable it.
UART_TXD/RXD- UART port data transmit and receive signal.
There is 1K Ohm pull-down resister internal. User can’t add pull-up resister at these pins.
1.3.2. 10/100M Ethernet Interface
HF-A11 modules provide one 10/100M Ethernet PHY layer interface for data transition or user
configuration. This Ethernet support with transformer and without transformer (PHY-to-PHY) 2
kinds of connection.
High-Flying
HF-A11 Embedded WiFi Module User Manual
Shanghai High-Flying Electronics Technology Co., Ltd
www.hi-flying.com 14
1.3.2.1. Ethernet Connection with Transformer
User board put Ethernet transformer and RJ-45 connector. This is a general 10/100M Ethernet
phy layer connection. The reference design as following:
Figure 9. Ethernet Reference Design with Transformer
1.3.2.2. Ethernet Connection without Transformer
For this application, Ethernet will work as internal data transmition interface and save one
transformer and RJ-45 connector. Ethernet PHY-to-PHY connection will use AC coupled
connection. This is a space and cost optimized solution. Hardware reference design as following:
Note: VCC signal at reference design shall base on user board PHY chipset voltage level, such
as 2.5V power supply for general Ethernet PHY chipset.
Figure 10. Ethernet Reference Design without Transformer
1.3.3. UART Interface
UART interface is the serial data transmition interface mainly used for HF-A11 modules.
User can add RS-232 chipset on user board and convert the signal to RS-232 voltage to
communicate with outside equipment or sensors. HF-A11 modules UART interface include 4
general signals: TXD/RXD/RTS/CTS. The hardware reference design with RS-232 chipset as
following:
High-Flying
HF-A11 Embedded WiFi Module User Manual
Shanghai High-Flying Electronics Technology Co., Ltd
www.hi-flying.com 15
Figure 11. UART Interface Reference Design
Notes:TXD pin is also hardware configuration pin internal module. So this pin MUST pull-down
during module power up. HF0A11x modules provide internal pull-down resister, user can’t add
pull-up/pull-down resister on user board, which may cause module can’t work.
1.3.4. Power Interface
HF-A11 module support single +3.3V power supply. The peak current shall about 350mA and
normal WiFi working current shall about 200mA. The power save (WiFi OFF) mode will about
100mA
Decoupling at power pin suggested, At least one 100uF and one 10uF capacitor required at user
board and put near module power input pin will increase the reliability and performance.
High-Flying
HF-A11 Embedded WiFi Module User Manual
Shanghai High-Flying Electronics Technology Co., Ltd
www.hi-flying.com 16
1.4. Software Reference Design
When HF-A11 modules boot up phase, the general user board MCU software flow chart will as
following:
Figure 12. User MCU Software Flow Chart
When HF-A11 modules boot up, user can select one work mode base on the setting, and user
can switch to the configuration mode at any kinds of work mode.
1.4.1. Transparent Transmission Mode
HF-A11 modules support serial interface transparent transmission mode. The benefit of this
mode is achieves a plug and play serial data port, and reduces user complexity furthest. In this
mode, user should only configure the necessary parameters. After power on, module can
automatically connect to the default wireless network and server.
As in this mode, the module's serial port always work in the transparent transmission mode, so
users only need to think of it as a virtual serial cable, and send and receive data as using a
simple serial. In other words, the serial cable of users’ original serial devices is directly replaced
with the module; user devices can be easy for wireless data transmission without any changes.
The transparent transmission mode can fully compatible with user’s original software platform
and reduce the software development effort for integrate wireless data transmission.
Notes: Transparent transmission mode as a low level phy layer data transmitting can't keep zero
error rates by itself. User can enable UART port’s hardware flow control CTS/RTS function or
though higher layer protocol such as TCP to lower error rate and mange the data completeness.
High-Flying recommend when doing large amounts of data transmitting in transparent
transmission mode, hardware flow control should be enabled, so as to fully ensure reliable data
transmission. In the applications which doesn’t need flow control, users can simply leave RTS /
CTS pin vacant.
1.4.2. Configuration Mode
In configuration mode, user can finish HF-A11 module configuration management and
parameters setting work. In work mode (Transparent Transmission or Agreement Transmission),
user can switch to the configuration mode through AT+instruction, detailed switch operation refer
to “AT+ instruction set” chapter.
High-Flying
HF-A11 Embedded WiFi Module User Manual
Shanghai High-Flying Electronics Technology Co., Ltd
www.hi-flying.com 17
1.4.3. Multi-TCP Link Connection
When HF-A11 module configured as TCP Server, it supports Multi-TCP link connection, and
maximum 32 TCP clients permit to connect to HF-A11 module. User can realize multi-TCP link
connection at each work mode.
Multi-TCP link connection will work as following structure:
Upstream: All dates from different TCP connection or client will be transmitted to the serial port as
a sequence.
Downstream: All data from serial port (user) will be duplicate and broadcast to every TCP
connection or client.
Detailed multi-TCP link data transmition structure as following figure:
Figure 13. Multi-TCP Link Data Transmition Structure
1.4.4. TCPB Function
HF-A11 support 2xTCP function, which means module can support 2 network connections at the
same time. The 2nd net work connection called TCPB. TCPB only works as TCP Client and its
configuration can only through AT commanrd, not Web configuration supported. The command
as following,
¾AT+TCPB=on, Enable TCPB function;
¾AT+TCPPTB=<port>, Set TCPB port number;
¾AT+TCPADDB=<IP or domain>, Set TCPB’s server address;
¾AT+TCPTOB=<time>, Set TCPB timeout;
¾AT+TCPLKB, Query TCPB link status;
Detailed command describtion refer ro AT instruction chapter. After enable TCPB function, two
network interfaces’ work mode like “Multi-TCP Link”, All dates from each TCP connection will be
transmitted to the serial port as a sequence and all data from serial port (user) will be duplicate
and broadcast to each TCP connection.
1.4.5. GPIO Function
HF-A11 module support 2 GPIO mode: GPIO-1 and GPIO-2. At GPIO-1 mode, UART (TXD/
RXD/CTS/RTS) defined as GPIO and others (nReady/nLink/nReload) defined as functional pin.
At GPIO-2, all these 7 pins defined as GPIO. So, GPIO mode not supports UART communication.
When module works at GPIO mode, PC and other equipts can setup connection (TCP/UDP)
through WiFi, then read/write GPIO information through command.
¾GPIO n IN, Set GPIOn as input, Response GPIO OK or GPIO NOK;
¾GPIO n OUT 0, Set GPIOn as output and output ‘0’, Response GPIO OK or GPIO NOK;
¾GPIO n OUT 1, Set GPIOn as output and output ‘1’, Response GPIO OK or GPIO NOK;
High-Flying
HF-A11 Embedded WiFi Module User Manual
Shanghai High-Flying Electronics Technology Co., Ltd
www.hi-flying.com 18
¾GPIO n SW, Set GPIOn as output and switch the output status, Response GPIO OK
or GPIO NOK;
¾GPIO n PWM m1 m2, Set GPIOn output a wave: m1 is ‘high’ duration and m2 is ’low’
duration (Time unit is ‘ms’ and minimal is 10ms), Response GPIO OK or GPIO NOK;
¾GPIO n GET, Read GPIOn status, Response I0,I1,O0,O1, means”input low”,”input
high”,”output low”,”output high”
Notes: n can be 3, 4, 5, 6, 8, 9, 10 corresponding module pin. GPIO 4 and 10 can only defined
as input and GPIO 3 can only defined as output.
1.4.6. Palmodic Signal
Base on selected factory default setting, nReady signal can have two output statuses:
¾Status One: The module will output “0” after normal boot up. This signal used to judge if
module finish boot up and ready for application.
¾Status Two: The module will output “Palmodic Signal” after normal boot up.The
palmodic signal is 0.5Hz square wave with dutyfactor 1:1. User can query this signal to
judge if moduleis active “live” or need to re-boot. When module switches to command
mode, it will output “0”, which used to distinguish work mode and command mode.
Notes:
This function is user selected factory setting and RELD instruction will not effective for this
function. If user not requires this function, the default factory setting is Status One. Contact with
Hi-flying for more detailed support.
High-Flying
HF-A11 Embedded WiFi Module User Manual
Shanghai High-Flying Electronics Technology Co., Ltd
www.hi-flying.com 19
2.FUNCTIONAL DESCRIPTION
2.1. Wireless Networking
HF-A11 module can be configured as both wireless STA and AP base on network type. Logically
there are two interfaces in HF-A11. One is for STA, and another is for AP. When HF-A11 works
as AP, other STA equipments are able to connect to wireless LAN via HF-A11 module. Wireless
Networking with HF-A11 is very flexible.
Following figure shows the functional architecture of HF-A11 module:
Figure 14. HF-A11 Functional Architecture
Notes:
AP: that is the wireless Access Point, the founder of a wireless network and the centre of the
network nodes. The wireless router we use at home or in office may be an AP.
STA: short for Station, each terminal connects to a wireless network (such as laptops, PDA and
other networking devices) can be called with a STA device.
2.1.1. Basic Wireless Network Based On AP (Infrastructure)
Infrastructure: it’s also called basic network. It built by AP and many STAs which join in.
The characters of network of this type are that AP is the centre, and all communication between
STAs is transmitted through the AP. The figure following shows such type of networking.
Figure 15. HF-A11 Basic Wireless Network Structure
High-Flying
HF-A11 Embedded WiFi Module User Manual
Shanghai High-Flying Electronics Technology Co., Ltd
www.hi-flying.com 20
2.1.2. Wireless Network Based On Adhoc Network (Adhoc)
Adhoc: It’s also called independent basic service set, and it’s built by two or more STAs without
AP, this type of network is a loose structure, all the STAs in the network can communicate
directly.
As showing in the figure below, HF-A11 (1) can be treat as an AP, and HF-A11 (2), HF-A11 (3)
and the laptop are STAs connected to HF-A11 (1). Meanwhile, all HF-A11 modules can
connected to user device via UART interface. All HF-A11 modules can be operated and
managed through the laptop. So it is convenient to O&M all HF-A11 modules. Moreover, in such
Adhoc network structure, the whole coverage of a wireless network can be extended easily.
Figure 16. HF-A11 Adhoc Network Structure
2.1.3. Wireless Network Based On AP+STA
HF-A11 module support AP+STA network mode, means module support one AP interface and
one STA interface at the same time, as following figure,
High-Flying
Table of contents
Other Hi-flying Network Card manuals
Popular Network Card manuals by other brands
Net to Net Technologies
Net to Net Technologies UIM-T1 installation instructions
Star Micronics
Star Micronics IFBD-HW03/04 s Product specifications manual
Toshiba
Toshiba Bluetooth Module Installation
Linksys
Linksys WCF11 - Wireless CompactFlash Card Type II Quick installation
Belkin
Belkin F5D9010uk user manual
TRENDnet
TRENDnet TEG-10GECTX Quick installation guide
Sanyo
Sanyo POA-MD17SDID POA-MD17SDID instruction manual
YOKOGAWA
YOKOGAWA Vnet/IP technical information
Rosewill
Rosewill RC-NIC416Dual user manual
OTC Wireless
OTC Wireless 802.11 Wireless Serial Solutions... Technical manual
SMC Networks
SMC Networks EZ Card 10 user guide
AMX
AMX NetLinx Master Card NXC-ME260-64 quick start guide
D-Link
D-Link DW-655C user guide
HP
HP Broadband Service Analyzer user manual
National Instruments
National Instruments MXI Series user manual
MikroTik
MikroTik RouterBOARD 711UA-2HnD Quick setup guide and warranty information
StarTech.com
StarTech.com 2 Port IEEE-1394 CardBus Card with Digital Video Editing... instruction manual
StarTech.com
StarTech.com EC1000S instruction manual