Hi-Spec HSA/BC/RF10-PRO User manual
LITHIUM BATTERY POWERED
CARBON MONOXIDE ALARM
MODEL:
HSA/BC/RF10-PRO
Main Features:
•Electrochemical Sensor
•Wireless interconnection via RF 868MHz
•Wireless Interconnect with max. 20pcs
RF-PRO Series alarm & control units
•Test/silence Button
•Low Battery Warning
•Self-Test Function
•Approved to EN50291-1:2010+A1:2012
This instruction leaflet contains importantinformation on
the correct installation and operation of your Carbon
Monoxide (CO) alarm. Read this leaflet fully before
attempting installation and retain for future reference.
SPECIFICATIONS
Power Source : ‘Lifetime Power’ 3V Lithium Battery
Battery Life : 10 Year (sealed)
Type of Gas sensed : Carbon Monoxide
Alarm Response Time : 50 PPM (Between 60 to 90 min.)
100 PPM (Between10 to 40 min.)
300 PPM (Less than 3 min.)
Operation Temperature : -10oC ~ 40oC
Ambient Humidity : 10%-90%
Sounder Level : 85 Decibels at 3 m
Wireless Interconnection
Radio Frequency : 868MHz
Interconnect method : Self-learn, self pair (Home Grouping)
Interconnect distance : 80m open area / 30m indoor area
Max interconnect unit : 20pcs Hispec RF-PRO Series alarm units
WHAT IS CARBON MONOXIDE
Carbon Monoxide (CO) is an insidious poison that is released when fuels
are burnt. It is a colourless, odourless,tasteless gas and therefore very
difficult to detect with the human senses. CO kills hundreds of people
each year and injures many more. It binds to the hemoglobin in the
blood and reduces the amount of oxygen being circulated in the
body. In high concentrations, CO can kill in minutes.
CO is produced by the incomplete combustion of fuels such as
wood, charcoal, coal, heating oil, paraffin, petrol, natural gas,
propane, butane etc.
Common Sources of CO:
Attached garages / Oil and Gas furnaces / Wood stoves /
Barbecues / Wood and gas fireplaces / Gas appliances / Portable
generators / Gas or kerosene heaters / Clogged chimneys /
Cigarette smoke
LOCATING THE CO ALARM
Ideally, a CO alarm should be installed in every room containing a
fuel burning appliance. Additional apparatus may be installed to
ensure that adequate warning is given for occupants in other
rooms, by locating apparatus in:
Remote rooms in which the occupant spend considerable time
whilst awake and from which they may not be able hear an
alarm from apparatus in another part of the premises, and
Every sleeping room.
However, if there is a fuel burning appliance in more than one
room and the number of CO alarm is limited, the following points
should be taken into consideration when deciding on the best
location:
An apparatus should be located in a room containing a flueless
or open-flued appliance.
If there is an appliance in a room where people spend most
time, an apparatus should be placed in that room.
If there is an appliance in a room where people sleep, an
apparatus should be placed in that room.
In a bedsit, the apparatus should be placed as far from the
cooking appliances as possible but near to where the person
sleeps.
If the appliance is in a room not normally used, such as boiler
room, the apparatus should be placed just outside the room so
that the alarm will be heard more easily.
CAUTION
This alarm will only indicate the presence of carbon monoxide
gas at the sensor. Carbon Monoxide gas may be present in
other areas.
This carbon monoxide alarm is designed to detect carbon
monoxide gas from ANY source of combustion. Itis NOT
designed to detect smoke, fire or any other gas.
POSITIONING THE CO ALARM
Carbon Monoxide has a similar density to warm air and can be
fitted in various locations.
Apparatus located in the same room as a fuel-burning
appliance:
If the apparatus is located on a wall, it should be located at a
height greater than the height of any door or window but at least
150 mm from the ceiling. If the apparatus is mounted on a
ceiling, it should be at least 300 mm from any wall.
The apparatus should be at a horizontal distance of between 1
m and 3 m from the potential source.
If there is partition in a room, the apparatus should be located
on the same side of the partition as the potential source.
In rooms with sloped ceilings, the apparatus should be located
at the high side of the room.
Apparatus located in sleeping rooms and in rooms remote
from a fuel burning appliance:
The apparatus should be located relatively close to the
breathing zone of the occupants.
Areas to be avoided include the following:
Situations where the temperature may drop below -10oC or
exceed 40oC
In a damp or humid area
Any area where high levels of dusty, dirty or greasy emissions
could contaminate or clog the sensor.
Where the air flow to the apparatus would be obstructed by
curtains or furniture.
Next to a door or window or in the path of air dischargedfrom a
furnace / air conditioning vent or ceiling fan.
Outside the building
Directly above a sink or cooker
In or below a cupboard
The following conditions can result in transient CO situations
in the home:
•Excessive spillage or reverse venting of fuel burning
appliances caused by:
1.) Outdoor ambient conditions such as wind direction and/or
velocity, including high gusts of wind; heavy air in the vent
pipes (cold/humid air with extended periods between
cycles).
2.) Negative pressure differential resulting from the use of
exhaust fans.
3.) Simultaneous operation of several fuel burning
appliances competing for limited internal air.
4.) Vent pipe connection vibrating loose from clothes dryers,
furnaces, or water heaters.
5.) Obstructions in or unconventional vent pipe designs
which amplify the above situations.
•Extended operation of unvented fuel burning devices (range,
oven, fireplace, etc.).
•Temperature inversions which can trap exhaust gases near
the ground.
•Car idling in an open or closed attached garage, or near a
home.
WARNING
This carbon monoxide alarm is designed for indoor use only.
Do not expose to rain or moisture. It will not protect against
the risk of carbon monoxide poisoning when the battery has
drained. Do not open or tamper with the alarm as this could
cause malfunction.
Installation of the apparatus should not be used as a
substitute for proper installation, use and maintenance of fuel
burning appliances including appropriate ventilation and
exhaust systems.
ALARM OVERVIEW
HOME GROUPING
This CO alarm can link up to 19 other CO, smoke and
heat alarms, and the control unit from the Hispec RF-PRO
range.
On the First Alarm;
- Hold the Test / Silence Button for 10 seconds. (RED LED
stays lit) Alarm is now in Home Grouping mode.
On all additional alarms;
- Press the Test / Silence Button 2 times slowly so the red & green
- The alarms are now Home Grouped.
Removing an alarm from the Home Group:
- Press the Test/Pairing Button 5 times slowly so the red &
green LEDs flash each time.
- The red LED on the CO unit will then flash 10 times to indicate
the CO unit has been reset.
INSTALLING AND ACTIVATING THE CO ALARM
This CO alarm is powered by a ‘Lifetime Power’ 3V Lithium battery and requires
no additional wiring. It can either be free-standing or installed on the wall
using the fixings provided.
Wall mount installation:
•Having established the mounting location, ensure that there is no
electrical wiring or pipe work in the area adjacent to the mounting
surface.
•Mark the mounting hole’s location.
•Drill holes in the position marked and insert the plastic wall plug
into the hole.
•Hook the alarm unit onto the screw and drag the alarm download
This will activate the CO Alarm and will cause it to make a loud chirp.
Read section “Alarm Condition” in OPERATING YOUR CO ALARM.
IMPORTANT: After installation, test your alarm (see the
paragraph “Test your CO alarm”.
The apparatus should be installed by a competent person.
OPERATING YOUR CO ALARM
During normal operation the CO alarm performs a self-check test every
minute.
Alarm Condition
LED Light
Condition Indication
Green Light
- Alarm Unit Activation
and Power on
Red Light
- High CO concentration
Warning
- Low Battery Signal
Yellow Light
- Unit Malfunction
- End of Life Signal
Plastic Wall Plug
LEDs flash each time. The red LED will flash 3 times.
LITHIUM BATTERY POWERED
CARBON MONOXIDE ALARM
MODEL:
HSA/BC/RF10-PRO
Main Features:
•Electrochemical Sensor
•Wireless interconnection via RF 868MHz
•Wireless Interconnect with max. 20pcs
RF-PRO Series alarm & control units
•Test/silence Button
•Low Battery Warning
•Self-Test Function
•Approved to EN50291-1:2010+A1:2012
This instruction leaflet contains importantinformation on
the correct installation and operation of your Carbon
Monoxide (CO) alarm. Read this leaflet fully before
attempting installation and retain for future reference.
SPECIFICATIONS
Power Source : ‘Lifetime Power’ 3V Lithium Battery
Battery Life : 10 Year (sealed)
Type of Gas sensed : Carbon Monoxide
Alarm Response Time : 50 PPM (Between 60 to 90 min.)
100 PPM (Between10 to 40 min.)
300 PPM (Less than 3 min.)
Operation Temperature : -10oC ~ 40oC
Ambient Humidity : 10%-90%
Sounder Level : 85 Decibels at 3 m
Wireless Interconnection
Radio Frequency : 868MHz
Interconnect method : Self-learn, self pair (Home Grouping)
Interconnect distance : 80m open area / 30m indoor area
Max interconnect unit : 20pcs Hispec RF-PRO Series alarm units
WHAT IS CARBON MONOXIDE
Carbon Monoxide (CO) is an insidious poison that is released when fuels
are burnt. It is a colourless, odourless,tasteless gas and therefore very
difficult to detect with the human senses. CO kills hundreds of people
each year and injures many more. It binds to the hemoglobin in the
blood and reduces the amount of oxygen being circulated in the
body. In high concentrations, CO can kill in minutes.
CO is produced by the incomplete combustion of fuels such as
wood, charcoal, coal, heating oil, paraffin, petrol, natural gas,
propane, butane etc.
Common Sources of CO:
Attached garages / Oil and Gas furnaces / Wood stoves /
Barbecues / Wood and gas fireplaces / Gas appliances / Portable
generators / Gas or kerosene heaters / Clogged chimneys /
Cigarette smoke
LOCATING THE CO ALARM
Ideally, a CO alarm should be installed in every room containing a
fuel burning appliance. Additional apparatus may be installed to
ensure that adequate warning is given for occupants in other
rooms, by locating apparatus in:
Remote rooms in which the occupant spend considerable time
whilst awake and from which they may not be able hear an
alarm from apparatus in another part of the premises, and
Every sleeping room.
However, if there is a fuel burning appliance in more than one
room and the number of CO alarm is limited, the following points
should be taken into consideration when deciding on the best
location:
An apparatus should be located in a room containing a flueless
or open-flued appliance.
If there is an appliance in a room where people spend most
time, an apparatus should be placed in that room.
If there is an appliance in a room where people sleep, an
apparatus should be placed in that room.
In a bedsit, the apparatus should be placed as far from the
cooking appliances as possible but near to where the person
sleeps.
If the appliance is in a room not normally used, such as boiler
room, the apparatus should be placed just outside the room so
that the alarm will be heard more easily.
CAUTION
This alarm will only indicate the presence of carbon monoxide
gas at the sensor. Carbon Monoxide gas may be present in
other areas.
This carbon monoxide alarm is designed to detect carbon
monoxide gas from ANY source of combustion. Itis NOT
designed to detect smoke, fire or any other gas.
POSITIONING THE CO ALARM
Carbon Monoxide has a similar density to warm air and can be
fitted in various locations.
Apparatus located in the same room as a fuel-burning
appliance:
If the apparatus is located on a wall, it should be located at a
height greater than the height of any door or window but at least
150 mm from the ceiling. If the apparatus is mounted on a
ceiling, it should be at least 300 mm from any wall.
The apparatus should be at a horizontal distance of between 1
m and 3 m from the potential source.
If there is partition in a room, the apparatus should be located
on the same side of the partition as the potential source.
In rooms with sloped ceilings, the apparatus should be located
at the high side of the room.
Apparatus located in sleeping rooms and in rooms remote
from a fuel burning appliance:
The apparatus should be located relatively close to the
breathing zone of the occupants.
Areas to be avoided include the following:
Situations where the temperature may drop below -10oC or
exceed 40oC
In a damp or humid area
Any area where high levels of dusty, dirty or greasy emissions
could contaminate or clog the sensor.
Where the air flow to the apparatus would be obstructed by
curtains or furniture.
Next to a door or window or in the path of air dischargedfrom a
furnace / air conditioning vent or ceiling fan.
Outside the building
Directly above a sink or cooker
In or below a cupboard
The following conditions can result in transient CO situations
in the home:
•Excessive spillage or reverse venting of fuel burning
appliances caused by:
1.) Outdoor ambient conditions such as wind direction and/or
velocity, including high gusts of wind; heavy air in the vent
pipes (cold/humid air with extended periods between
cycles).
2.) Negative pressure differential resulting from the use of
exhaust fans.
3.) Simultaneous operation of several fuel burning
appliances competing for limited internal air.
4.) Vent pipe connection vibrating loose from clothes dryers,
furnaces, or water heaters.
5.) Obstructions in or unconventional vent pipe designs
which amplify the above situations.
•Extended operation of unvented fuel burning devices (range,
oven, fireplace, etc.).
•Temperature inversions which can trap exhaust gases near
the ground.
•Car idling in an open or closed attached garage, or near a
home.
WARNING
This carbon monoxide alarm is designed for indoor use only.
Do not expose to rain or moisture. It will not protect against
the risk of carbon monoxide poisoning when the battery has
drained. Do not open or tamper with the alarm as this could
cause malfunction.
Installation of the apparatus should not be used as a
substitute for proper installation, use and maintenance of fuel
burning appliances including appropriate ventilation and
exhaust systems.
ALARM OVERVIEW
HOME GROUPING
This CO alarm can link up to 19 other CO, smoke and
heat alarms, and the control unit from the Hispec RF-PRO
range.
On the First Alarm;
- Hold the Test / Silence Button for 10 seconds. (RED LED
stays lit) Alarm is now in Home Grouping mode.
On all additional alarms;
- Press the Test / Silence Button 2 times slowly so the red & green
- The alarms are now Home Grouped.
Removing an alarm from the Home Group:
- Press the Test/Pairing Button 5 times slowly so the red &
green LEDs flash each time.
- The red LED on the CO unit will then flash 10 times to indicate
the CO unit has been reset.
INSTALLING AND ACTIVATING THE CO ALARM
This CO alarm is powered by a ‘Lifetime Power’ 3V Lithium battery and requires
no additional wiring. It can either be free-standing or installed on the wall
using the fixings provided.
Wall mount installation:
•Having established the mounting location, ensure that there is no
electrical wiring or pipe work in the area adjacent to the mounting
surface.
•Mark the mounting hole’s location.
•Drill holes in the position marked and insert the plastic wall plug
into the hole.
•Hook the alarm unit onto the screw and drag the alarm download
This will activate the CO Alarm and will cause it to make a loud chirp.
Read section “Alarm Condition” in OPERATING YOUR CO ALARM.
IMPORTANT: After installation, test your alarm (see the
paragraph “Test your CO alarm”.
The apparatus should be installed by a competent person.
OPERATING YOUR CO ALARM
During normal operation the CO alarm performs a self-check test every
minute.
Alarm Condition
LED Light
Condition Indication
Green Light
- Alarm Unit Activation
and Power on
Red Light
- High CO concentration
Warning
- Low Battery Signal
Yellow Light
- Unit Malfunction
- End of Life Signal
Plastic Wall Plug
LEDs flash each time. The red LED will flash 3 times.
LITHIUM BATTERY POWERED
CARBON MONOXIDE ALARM
MODEL:
HSA/BC/RF10-PRO
Main Features:
•Electrochemical Sensor
•Wireless interconnection via RF 868MHz
•Wireless Interconnect with max. 20pcs
RF-PRO Series alarm & control units
•Test/silence Button
•Low Battery Warning
•Self-Test Function
•Approved to EN50291-1:2010+A1:2012
This instruction leaflet contains importantinformation on
the correct installation and operation of your Carbon
Monoxide (CO) alarm. Read this leaflet fully before
attempting installation and retain for future reference.
SPECIFICATIONS
Power Source : ‘Lifetime Power’ 3V Lithium Battery
Battery Life : 10 Year (sealed)
Type of Gas sensed : Carbon Monoxide
Alarm Response Time : 50 PPM (Between 60 to 90 min.)
100 PPM (Between10 to 40 min.)
300 PPM (Less than 3 min.)
Operation Temperature : -10oC ~ 40oC
Ambient Humidity : 10%-90%
Sounder Level : 85 Decibels at 3 m
Wireless Interconnection
Radio Frequency : 868MHz
Interconnect method : Self-learn, self pair (Home Grouping)
Interconnect distance : 80m open area / 30m indoor area
Max interconnect unit : 20pcs Hispec RF-PRO Series alarm units
WHAT IS CARBON MONOXIDE
Carbon Monoxide (CO) is an insidious poison that is released when fuels
are burnt. It is a colourless, odourless,tasteless gas and therefore very
difficult to detect with the human senses. CO kills hundreds of people
each year and injures many more. It binds to the hemoglobin in the
blood and reduces the amount of oxygen being circulated in the
body. In high concentrations, CO can kill in minutes.
CO is produced by the incomplete combustion of fuels such as
wood, charcoal, coal, heating oil, paraffin, petrol, natural gas,
propane, butane etc.
Common Sources of CO:
Attached garages / Oil and Gas furnaces / Wood stoves /
Barbecues / Wood and gas fireplaces / Gas appliances / Portable
generators / Gas or kerosene heaters / Clogged chimneys /
Cigarette smoke
LOCATING THE CO ALARM
Ideally, a CO alarm should be installed in every room containing a
fuel burning appliance. Additional apparatus may be installed to
ensure that adequate warning is given for occupants in other
rooms, by locating apparatus in:
Remote rooms in which the occupant spend considerable time
whilst awake and from which they may not be able hear an
alarm from apparatus in another part of the premises, and
Every sleeping room.
However, if there is a fuel burning appliance in more than one
room and the number of CO alarm is limited, the following points
should be taken into consideration when deciding on the best
location:
An apparatus should be located in a room containing a flueless
or open-flued appliance.
If there is an appliance in a room where people spend most
time, an apparatus should be placed in that room.
If there is an appliance in a room where people sleep, an
apparatus should be placed in that room.
In a bedsit, the apparatus should be placed as far from the
cooking appliances as possible but near to where the person
sleeps.
If the appliance is in a room not normally used, such as boiler
room, the apparatus should be placed just outside the room so
that the alarm will be heard more easily.
CAUTION
This alarm will only indicate the presence of carbon monoxide
gas at the sensor. Carbon Monoxide gas may be present in
other areas.
This carbon monoxide alarm is designed to detect carbon
monoxide gas from ANY source of combustion. Itis NOT
designed to detect smoke, fire or any other gas.
POSITIONING THE CO ALARM
Carbon Monoxide has a similar density to warm air and can be
fitted in various locations.
Apparatus located in the same room as a fuel-burning
appliance:
If the apparatus is located on a wall, it should be located at a
height greater than the height of any door or window but at least
150 mm from the ceiling. If the apparatus is mounted on a
ceiling, it should be at least 300 mm from any wall.
The apparatus should be at a horizontal distance of between 1
m and 3 m from the potential source.
If there is partition in a room, the apparatus should be located
on the same side of the partition as the potential source.
In rooms with sloped ceilings, the apparatus should be located
at the high side of the room.
Apparatus located in sleeping rooms and in rooms remote
from a fuel burning appliance:
The apparatus should be located relatively close to the
breathing zone of the occupants.
Areas to be avoided include the following:
Situations where the temperature may drop below -10oC or
exceed 40oC
In a damp or humid area
Any area where high levels of dusty, dirty or greasy emissions
could contaminate or clog the sensor.
Where the air flow to the apparatus would be obstructed by
curtains or furniture.
Next to a door or window or in the path of air dischargedfrom a
furnace / air conditioning vent or ceiling fan.
Outside the building
Directly above a sink or cooker
In or below a cupboard
The following conditions can result in transient CO situations
in the home:
•Excessive spillage or reverse venting of fuel burning
appliances caused by:
1.) Outdoor ambient conditions such as wind direction and/or
velocity, including high gusts of wind; heavy air in the vent
pipes (cold/humid air with extended periods between
cycles).
2.) Negative pressure differential resulting from the use of
exhaust fans.
3.) Simultaneous operation of several fuel burning
appliances competing for limited internal air.
4.) Vent pipe connection vibrating loose from clothes dryers,
furnaces, or water heaters.
5.) Obstructions in or unconventional vent pipe designs
which amplify the above situations.
•Extended operation of unvented fuel burning devices (range,
oven, fireplace, etc.).
•Temperature inversions which can trap exhaust gases near
the ground.
•Car idling in an open or closed attached garage, or near a
home.
WARNING
This carbon monoxide alarm is designed for indoor use only.
Do not expose to rain or moisture. It will not protect against
the risk of carbon monoxide poisoning when the battery has
drained. Do not open or tamper with the alarm as this could
cause malfunction.
Installation of the apparatus should not be used as a
substitute for proper installation, use and maintenance of fuel
burning appliances including appropriate ventilation and
exhaust systems.
ALARM OVERVIEW
HOME GROUPING
This CO alarm can link up to 19 other CO, smoke and
heat alarms, and the control unit from the Hispec RF-PRO
range.
On the First Alarm;
- Hold the Test / Silence Button for 10 seconds. (RED LED
stays lit) Alarm is now in Home Grouping mode.
On all additional alarms;
- Press the Test / Silence Button 2 times slowly so the red & green
- The alarms are now Home Grouped.
Removing an alarm from the Home Group:
- Press the Test/Pairing Button 5 times slowly so the red &
green LEDs flash each time.
- The red LED on the CO unit will then flash 10 times to indicate
the CO unit has been reset.
INSTALLING AND ACTIVATING THE CO ALARM
This CO alarm is powered by a ‘Lifetime Power’ 3V Lithium battery and requires
no additional wiring. It can either be free-standing or installed on the wall
using the fixings provided.
Wall mount installation:
•Having established the mounting location, ensure that there is no
electrical wiring or pipe work in the area adjacent to the mounting
surface.
•Mark the mounting hole’s location.
•Drill holes in the position marked and insert the plastic wall plug
into the hole.
•Hook the alarm unit onto the screw and drag the alarm download
This will activate the CO Alarm and will cause it to make a loud chirp.
Read section “Alarm Condition” in OPERATING YOUR CO ALARM.
IMPORTANT: After installation, test your alarm (see the
paragraph “Test your CO alarm”.
The apparatus should be installed by a competent person.
OPERATING YOUR CO ALARM
During normal operation the CO alarm performs a self-check test every
minute.
Alarm Condition
LED Light
Condition Indication
Green Light
- Alarm Unit Activation
and Power on
Red Light
- High CO concentration
Warning
- Low Battery Signal
Yellow Light
- Unit Malfunction
- End of Life Signal
Plastic Wall Plug
LEDs flash each time. The red LED will flash 3 times.
LITHIUM BATTERY POWERED
CARBON MONOXIDE ALARM
MODEL:
HSA/BC/RF10-PRO
Main Features:
•Electrochemical Sensor
•Wireless interconnection via RF 868MHz
•Wireless Interconnect with max. 20pcs
RF-PRO Series alarm & control units
•Test/silence Button
•Low Battery Warning
•Self-Test Function
•Approved to EN50291-1:2010+A1:2012
This instruction leaflet contains importantinformation on
the correct installation and operation of your Carbon
Monoxide (CO) alarm. Read this leaflet fully before
attempting installation and retain for future reference.
SPECIFICATIONS
Power Source : ‘Lifetime Power’ 3V Lithium Battery
Battery Life : 10 Year (sealed)
Type of Gas sensed : Carbon Monoxide
Alarm Response Time : 50 PPM (Between 60 to 90 min.)
100 PPM (Between10 to 40 min.)
300 PPM (Less than 3 min.)
Operation Temperature : -10oC ~ 40oC
Ambient Humidity : 10%-90%
Sounder Level : 85 Decibels at 3 m
Wireless Interconnection
Radio Frequency : 868MHz
Interconnect method : Self-learn, self pair (Home Grouping)
Interconnect distance : 80m open area / 30m indoor area
Max interconnect unit : 20pcs Hispec RF-PRO Series alarm units
WHAT IS CARBON MONOXIDE
Carbon Monoxide (CO) is an insidious poison that is released when fuels
are burnt. It is a colourless, odourless,tasteless gas and therefore very
difficult to detect with the human senses. CO kills hundreds of people
each year and injures many more. It binds to the hemoglobin in the
blood and reduces the amount of oxygen being circulated in the
body. In high concentrations, CO can kill in minutes.
CO is produced by the incomplete combustion of fuels such as
wood, charcoal, coal, heating oil, paraffin, petrol, natural gas,
propane, butane etc.
Common Sources of CO:
Attached garages / Oil and Gas furnaces / Wood stoves /
Barbecues / Wood and gas fireplaces / Gas appliances / Portable
generators / Gas or kerosene heaters / Clogged chimneys /
Cigarette smoke
LOCATING THE CO ALARM
Ideally, a CO alarm should be installed in every room containing a
fuel burning appliance. Additional apparatus may be installed to
ensure that adequate warning is given for occupants in other
rooms, by locating apparatus in:
Remote rooms in which the occupant spend considerable time
whilst awake and from which they may not be able hear an
alarm from apparatus in another part of the premises, and
Every sleeping room.
However, if there is a fuel burning appliance in more than one
room and the number of CO alarm is limited, the following points
should be taken into consideration when deciding on the best
location:
An apparatus should be located in a room containing a flueless
or open-flued appliance.
If there is an appliance in a room where people spend most
time, an apparatus should be placed in that room.
If there is an appliance in a room where people sleep, an
apparatus should be placed in that room.
In a bedsit, the apparatus should be placed as far from the
cooking appliances as possible but near to where the person
sleeps.
If the appliance is in a room not normally used, such as boiler
room, the apparatus should be placed just outside the room so
that the alarm will be heard more easily.
CAUTION
This alarm will only indicate the presence of carbon monoxide
gas at the sensor. Carbon Monoxide gas may be present in
other areas.
This carbon monoxide alarm is designed to detect carbon
monoxide gas from ANY source of combustion. Itis NOT
designed to detect smoke, fire or any other gas.
POSITIONING THE CO ALARM
Carbon Monoxide has a similar density to warm air and can be
fitted in various locations.
Apparatus located in the same room as a fuel-burning
appliance:
If the apparatus is located on a wall, it should be located at a
height greater than the height of any door or window but at least
150 mm from the ceiling. If the apparatus is mounted on a
ceiling, it should be at least 300 mm from any wall.
The apparatus should be at a horizontal distance of between 1
m and 3 m from the potential source.
If there is partition in a room, the apparatus should be located
on the same side of the partition as the potential source.
In rooms with sloped ceilings, the apparatus should be located
at the high side of the room.
Apparatus located in sleeping rooms and in rooms remote
from a fuel burning appliance:
The apparatus should be located relatively close to the
breathing zone of the occupants.
Areas to be avoided include the following:
Situations where the temperature may drop below -10oC or
exceed 40oC
In a damp or humid area
Any area where high levels of dusty, dirty or greasy emissions
could contaminate or clog the sensor.
Where the air flow to the apparatus would be obstructed by
curtains or furniture.
Next to a door or window or in the path of air dischargedfrom a
furnace / air conditioning vent or ceiling fan.
Outside the building
Directly above a sink or cooker
In or below a cupboard
The following conditions can result in transient CO situations
in the home:
•Excessive spillage or reverse venting of fuel burning
appliances caused by:
1.) Outdoor ambient conditions such as wind direction and/or
velocity, including high gusts of wind; heavy air in the vent
pipes (cold/humid air with extended periods between
cycles).
2.) Negative pressure differential resulting from the use of
exhaust fans.
3.) Simultaneous operation of several fuel burning
appliances competing for limited internal air.
4.) Vent pipe connection vibrating loose from clothes dryers,
furnaces, or water heaters.
5.) Obstructions in or unconventional vent pipe designs
which amplify the above situations.
•Extended operation of unvented fuel burning devices (range,
oven, fireplace, etc.).
•Temperature inversions which can trap exhaust gases near
the ground.
•Car idling in an open or closed attached garage, or near a
home.
WARNING
This carbon monoxide alarm is designed for indoor use only.
Do not expose to rain or moisture. It will not protect against
the risk of carbon monoxide poisoning when the battery has
drained. Do not open or tamper with the alarm as this could
cause malfunction.
Installation of the apparatus should not be used as a
substitute for proper installation, use and maintenance of fuel
burning appliances including appropriate ventilation and
exhaust systems.
ALARM OVERVIEW
HOME GROUPING
This CO alarm can link up to 19 other CO, smoke and
heat alarms, and the control unit from the Hispec RF-PRO
range.
On the First Alarm;
- Hold the Test / Silence Button for 10 seconds. (RED LED
stays lit) Alarm is now in Home Grouping mode.
On all additional alarms;
- Press the Test / Silence Button 2 times slowly so the red & green
- The alarms are now Home Grouped.
Removing an alarm from the Home Group:
- Press the Test/Pairing Button 5 times slowly so the red &
green LEDs flash each time.
- The red LED on the CO unit will then flash 10 times to indicate
the CO unit has been reset.
INSTALLING AND ACTIVATING THE CO ALARM
This CO alarm is powered by a ‘Lifetime Power’ 3V Lithium battery and requires
no additional wiring. It can either be free-standing or installed on the wall
using the fixings provided.
Wall mount installation:
•Having established the mounting location, ensure that there is no
electrical wiring or pipe work in the area adjacent to the mounting
surface.
•Mark the mounting hole’s location.
•Drill holes in the position marked and insert the plastic wall plug
into the hole.
•Hook the alarm unit onto the screw and drag the alarm download
This will activate the CO Alarm and will cause it to make a loud chirp.
Read section “Alarm Condition” in OPERATING YOUR CO ALARM.
IMPORTANT: After installation, test your alarm (see the
paragraph “Test your CO alarm”.
The apparatus should be installed by a competent person.
OPERATING YOUR CO ALARM
During normal operation the CO alarm performs a self-check test every
minute.
Alarm Condition
LED Light
Condition Indication
Green Light
- Alarm Unit Activation
and Power on
Red Light
- High CO concentration
Warning
- Low Battery Signal
Yellow Light
- Unit Malfunction
- End of Life Signal
Plastic Wall Plug
LEDs flash each time. The red LED will flash 3 times.
Alarm unit Activation and Power on
After the CO Alarm is hooked on and installed, the green LED will flash
5 times. Then, the green LED will continuallyflash every 48 seconds
to indicate power is on.
High CO Concentration Warning
When the apparatus detects dangerous levels of CO gas, it will give an
alarm signal. The red LED will flash and the sounder will chirp 4 times
simultaneously every 5 seconds.
CO LEVEL (PPM) RESPONSE TIME (MIN)
50 60-90
100 10-40
300 < 3
WARNING
This product may not alarm at low carbon monoxide levels.
Individuals with medical problems may consider using warning
devices which provide audible signals for carbon monoxide
concentrations under 30 PPM.
Test / Hush Function
While the CO Alarm is chirping, press and hold the Test /
silence button for 2 seconds. If the CO alarm detects a CO
concentration under 30ppm, the alarm unit will be silenced for 10
hours. If the alarm unit did not silence, that means the CO Level
is higher than 30ppm. Read Section – “WHAT TO DO IF THE
ALARM SOUNDS”.
Low Battery Signal
In case the battery is at the end of its life, the apparatus will sound a short
chirp with a Yelllow LED flash simultaneously every minute. This low
voltage warning will be given for at least 7 days.
Under normal operating conditions, the batteries will last ten years.
End of Life Signal
After 10 years operation, the yellow LED will flash 3 times and beep 3
times simultaneously every 48 seconds. Read below “Deactivating Unit”.
Unit Malfunction
Your CO alarm performs an internal self-diagnosis every minute to make
sure that it is functioning properly. In the rare event that your alarm
malfunctions, the apparatus will sound a double short chirp and the
yellow LED will flash simultaneously every minute. In this case the alarm
must be replaced.
Never ignore a CO unit’s alarm. A true alarm is an indication of potentially
dangerous levels of carbon monoxide. CO alarms are designed to alert you
to the presence of carbon monoxide before an emergency, before most
people would experience symptoms of carbon monoxide poisoning, giving
you time to resolve the problem. Read section “What to do if alarm sounds”.
If the CO alarm is confirmed to be faulty or at the end of it’s life, you may
uninstall and deactivate the CO alarm by following these steps:
•Unhook the alarm unit from wall.
•Use a screwdriver to lever the deactivation clip out
•Fit the deactivation clip into the clip hole and push downward
•The alarm unit is now deactivated
TESTING YOUR CO ALARM
SILENCE FEATURE
WHAT TO DO IF THE ALARM SOUNDS
WARNING
Activation of your CO alarm indicates the presence of carbon
Monoxide (CO), which can KILL YOU.
If alarm signal sounds:
1. Immediately move tofresh air – outdoors or by an open
door/window. Do a head count to check that all persons are
accounted for.
2. Where possible turn off all fuelled appliances and stop using
them.
3. Call your emergency services if anybody is unwell or missing.
4. Do not re-enter the premises nor move away from the open
door/window until emergency services responders have arrived,
the premises have been aired out, and your alarm remains in its
normal condition.
5. Call a qualified appliance technician to investigate for sources
of CO from fuel burning equipment and appliances, and inspect
for proper operation of this equipment. If problems are identified
during this inspection have the equipment serviced immediately.
Note any combustion equipment not inspected by the technician
and consult the manufacturers’ instructions, or contact the
manufacturers directly, for more information about CO safety
and this equipment. Make sure that motor vehicles are not, and
have not been, operating in an attached garage or adjacent to
the residence.
MAINTAINING YOUR CO ALARM
Your alarm will alert you to potentially hazardous CO
concentrations in your home when maintained properly. To
maintain your alarm in proper working order, it is recommended
that you:
•Test your alarm at least once a month.
•Clean the outside case regularly to prevent dust or dirt build
up in the slots. DO NOT USE CLEANING AGENTS,
BLEACH, POLISH OR ANY CHEMICALS. Chemicals
can permanently damage or temporarily contaminate the
sensor. Simply wipe with a damp cloth OR a clean tissue.
•Do not paint the CO alarm
NOTE - If you will be staining or stripping wood floors or furniture,
painting, wall-papering, or using aerosols or adhesives, remove
the CO alarm to a remote location beforehand in order to prevent
possible damage to or contamination of the sensor.
The following is a list of substances which, at high levels, can
affect the sensor and may cause a nuisance alarm that is not a
carbon monoxide alarm.
Methane, propane, iso-butane, ethylene, ethanol, alcohol, iso-
propanol, benzene, toluene, ethyl acetate, hydrogen, hydrogen
sulfide, sulfur dioxides. Also most aerosol sprays, alcohol based
products, paints, solvents, adhesives, hair sprays, after shaves,
perfumes and some cleaning agents.
NOTE: THE APPARATUS SHALL NOT BE EXPOSED
TO DRIPPING OR SPLASHING.
SYMPTOMS OF CO POISONING
The following symptoms may be related to CO poisoning:
35 ppm The maximum allowable concentration for
continuous exposure for healthy adults in any
8 hour period.
200 ppm Slight headaches, fatigue, dizziness, nausea
after 2-3 hours
400 ppm Frontal headaches within 1-2 hours, life
threatening after 3 hours.
800 ppm Dizziness, nausea and convulsions within 45
minutes. Unconsciousness within 2 hours. Death
within 3 hours.
1600 ppm Headache, dizziness and nausea within 20
minutes. Death within 1 hour
6400 ppm Headache, dizziness and nausea within 1-2
minutes
The following symptoms are related to CARBON MONOXIDE
POISONING and are to be discussed with ALL members of the
household:
Mild Exposure: Slight headache, nausea, vomiting, fatigue (often
described as “flu-like” symptoms).
Medium Exposure: Severe throbbing headache, drowsiness,
confusion, fast heart rate.
Extreme Exposure: Unconsciousness, convulsions, cardio-
respiratory failure, death.
Many cases of reported CARBON MONOXIDE POISONING
indicate that while victims are aware they are not well, they
become so disoriented they are unable to save themselves by
leaving the building or calling for assistance. Young children and
household pets are typically the first affected.
The apparatus may not prevent the chronic effects of carbon
dioxide exposure and it will not fully safeguard individuals
at special risk.
IMPORTANT SAFEGUARDS
Installation of your CO alarm is only one step in your safety plan.
Educate yourself and familyto the sources and symptoms of CO
poisoning and how to use your carbon monoxide alarm:-
•Buy appliances approved by a recognized testing laboratory.
•Install the appliances properly, following the manufacturers’
instructions.
•Have installations done by professionals.
•Have your appliances checked regularly by a qualified
serviceman.
•Clean chimneys and flues yearly.
•Make regular visual inspections of all-fuel-burning
appliances.
•Check appliances for excessive rust and scaling.
•Do not barbecue indoors, or in attached garage.
•Open windows when a fireplace or wood burning stove is in
use.
•Be aware of CO poisoning symptoms.
DO NOT:
•Burn charcoal inside your home, RV, camper, tent or cabin
•Install, convert or service fuel burning appliances without proper
knowledge, skill and expertise
•Use a gas range, oven or clothes dryer for heating
•Operate unvented gas burning appliances using kerosene or
natural gas in closed room
•Operate gasoline powered engines indoors or in confined areas
•Ignore a safety device when it shuts an appliance off
•Ignore any warning from your CO alarm
END OF UNIT LIFE
With normal use the battery will last at least 10 years. However,
battery life will be reduced if the apparatus remains in alarm for
long periods of time.
The apparatus must be replaced when a fault warning signal is given.
NOTE: BATTERY SEALED-IN NOT FOR
REPLACEMENT
THIS PRODUCT CANNOT BE REPAIRED – IF THE UNIT IS
TAMPERED WITH IT WILL INVALIDATE THE GUARANTEE.
IF THE UNIT IS FAULTY PLEASE RETURN IT TO YOUR ORIGINAL
SUPPLIER WITH YOUR PROOF OF PURCHASE.
YOUR CO ALARM WARRANTY
Manufacturer:
Hispec Electrical Products Ltd
Unit 21 Chorley North Business Park
Chorley
Lancashire
PR6 7BX
www.hispec.co.uk
VER: Nov 2020
-
Deactivating Unit
These CO alarms are warranted to be free from defects in materials and
workmanship, under normal use and service, for a period of five (5) years
from date of purchase. Hispec will not be obligated to repair or replace
parts, which are found to be in need of repair due to misuse, damage, or
alterations occurring after the date of purchase. The liability of Hispec,
arising from the sale of this CO alarm, shall not in any case exceed the
cost of the purchase price of the CO alarm. In no case shall Hispec be
liable for personal injury, property damage, or any other consequential loss
or damage, resulting from the failure of the fire alarm.
CO alarms are not a substitute for property, life, or other insurance of any
kind.
This does not affect your statutory rights.
This alarm is suitable for private dwellings only and is not intended for
commercial or industrial dwellings.
Waste electrical products should not be disposed of with normal household
waste. Please recycle where facilities exist. Check with your Local
Authority or retailer for recycling advice. Regulations encourage the
recycling of Waste from Electrical and Electronic Equipment (European
"WEEE Directive" effective August 2005).
Important: The alarm will not silence if it has detected carbon
monoxide gas. (CO concentration higher than 30ppm). The
silence function is applicable only to the Low Battery Warning
Signal, End of Life Signal and Fault Warning signal.
To operate the silence feature, press the test button and hold for
approximately 3 seconds. The alarm unit will enter a dormant
period for 10 hours. After 10 hours, the CO alarm will resume its
operation. You should be alert to the signal the alarm gives and
replace the unit.
It is recommended that you test your CO alarm once a month to
ensure it is working correctly.
Test the unit by holding the Test / Silence button for 3 seconds. The
sounder will chirp 4 times and the red LED will flash for 30 seconds.
The unit will then enter back into normal operation mode.
Alarm unit Activation and Power on
After the CO Alarm is hooked on and installed, the green LED will flash
5 times. Then, the green LED will continuallyflash every 48 seconds
to indicate power is on.
High CO Concentration Warning
When the apparatus detects dangerous levels of CO gas, it will give an
alarm signal. The red LED will flash and the sounder will chirp 4 times
simultaneously every 5 seconds.
CO LEVEL (PPM) RESPONSE TIME (MIN)
50 60-90
100 10-40
300 < 3
WARNING
This product may not alarm at low carbon monoxide levels.
Individuals with medical problems may consider using warning
devices which provide audible signals for carbon monoxide
concentrations under 30 PPM.
Test / Hush Function
While the CO Alarm is chirping, press and hold the Test /
silence button for 2 seconds. If the CO alarm detects a CO
concentration under 30ppm, the alarm unit will be silenced for 10
hours. If the alarm unit did not silence, that means the CO Level
is higher than 30ppm. Read Section – “WHAT TO DO IF THE
ALARM SOUNDS”.
Low Battery Signal
In case the battery is at the end of its life, the apparatus will sound a short
chirp with a Yelllow LED flash simultaneously every minute. This low
voltage warning will be given for at least 7 days.
Under normal operating conditions, the batteries will last ten years.
End of Life Signal
After 10 years operation, the yellow LED will flash 3 times and beep 3
times simultaneously every 48 seconds. Read below “Deactivating Unit”.
Unit Malfunction
Your CO alarm performs an internal self-diagnosis every minute to make
sure that it is functioning properly. In the rare event that your alarm
malfunctions, the apparatus will sound a double short chirp and the
yellow LED will flash simultaneously every minute. In this case the alarm
must be replaced.
Never ignore a CO unit’s alarm. A true alarm is an indication of potentially
dangerous levels of carbon monoxide. CO alarms are designed to alert you
to the presence of carbon monoxide before an emergency, before most
people would experience symptoms of carbon monoxide poisoning, giving
you time to resolve the problem. Read section “What to do if alarm sounds”.
If the CO alarm is confirmed to be faulty or at the end of it’s life, you may
uninstall and deactivate the CO alarm by following these steps:
•Unhook the alarm unit from wall.
•Use a screwdriver to lever the deactivation clip out
•Fit the deactivation clip into the clip hole and push downward
•The alarm unit is now deactivated
TESTING YOUR CO ALARM
SILENCE FEATURE
WHAT TO DO IF THE ALARM SOUNDS
WARNING
Activation of your CO alarm indicates the presence of carbon
Monoxide (CO), which can KILL YOU.
If alarm signal sounds:
1. Immediately move tofresh air – outdoors or by an open
door/window. Do a head count to check that all persons are
accounted for.
2. Where possible turn off all fuelled appliances and stop using
them.
3. Call your emergency services if anybody is unwell or missing.
4. Do not re-enter the premises nor move away from the open
door/window until emergency services responders have arrived,
the premises have been aired out, and your alarm remains in its
normal condition.
5. Call a qualified appliance technician to investigate for sources
of CO from fuel burning equipment and appliances, and inspect
for proper operation of this equipment. If problems are identified
during this inspection have the equipment serviced immediately.
Note any combustion equipment not inspected by the technician
and consult the manufacturers’ instructions, or contact the
manufacturers directly, for more information about CO safety
and this equipment. Make sure that motor vehicles are not, and
have not been, operating in an attached garage or adjacent to
the residence.
MAINTAINING YOUR CO ALARM
Your alarm will alert you to potentially hazardous CO
concentrations in your home when maintained properly. To
maintain your alarm in proper working order, it is recommended
that you:
•Test your alarm at least once a month.
•Clean the outside case regularly to prevent dust or dirt build
up in the slots. DO NOT USE CLEANING AGENTS,
BLEACH, POLISH OR ANY CHEMICALS. Chemicals
can permanently damage or temporarily contaminate the
sensor. Simply wipe with a damp cloth OR a clean tissue.
•Do not paint the CO alarm
NOTE - If you will be staining or stripping wood floors or furniture,
painting, wall-papering, or using aerosols or adhesives, remove
the CO alarm to a remote location beforehand in order to prevent
possible damage to or contamination of the sensor.
The following is a list of substances which, at high levels, can
affect the sensor and may cause a nuisance alarm that is not a
carbon monoxide alarm.
Methane, propane, iso-butane, ethylene, ethanol, alcohol, iso-
propanol, benzene, toluene, ethyl acetate, hydrogen, hydrogen
sulfide, sulfur dioxides. Also most aerosol sprays, alcohol based
products, paints, solvents, adhesives, hair sprays, after shaves,
perfumes and some cleaning agents.
NOTE: THE APPARATUS SHALL NOT BE EXPOSED
TO DRIPPING OR SPLASHING.
SYMPTOMS OF CO POISONING
The following symptoms may be related to CO poisoning:
35 ppm The maximum allowable concentration for
continuous exposure for healthy adults in any
8 hour period.
200 ppm Slight headaches, fatigue, dizziness, nausea
after 2-3 hours
400 ppm Frontal headaches within 1-2 hours, life
threatening after 3 hours.
800 ppm Dizziness, nausea and convulsions within 45
minutes. Unconsciousness within 2 hours. Death
within 3 hours.
1600 ppm Headache, dizziness and nausea within 20
minutes. Death within 1 hour
6400 ppm Headache, dizziness and nausea within 1-2
minutes
The following symptoms are related to CARBON MONOXIDE
POISONING and are to be discussed with ALL members of the
household:
Mild Exposure: Slight headache, nausea, vomiting, fatigue (often
described as “flu-like” symptoms).
Medium Exposure: Severe throbbing headache, drowsiness,
confusion, fast heart rate.
Extreme Exposure: Unconsciousness, convulsions, cardio-
respiratory failure, death.
Many cases of reported CARBON MONOXIDE POISONING
indicate that while victims are aware they are not well, they
become so disoriented they are unable to save themselves by
leaving the building or calling for assistance. Young children and
household pets are typically the first affected.
The apparatus may not prevent the chronic effects of carbon
dioxide exposure and it will not fully safeguard individuals
at special risk.
IMPORTANT SAFEGUARDS
Installation of your CO alarm is only one step in your safety plan.
Educate yourself and familyto the sources and symptoms of CO
poisoning and how to use your carbon monoxide alarm:-
•Buy appliances approved by a recognized testing laboratory.
•Install the appliances properly, following the manufacturers’
instructions.
•Have installations done by professionals.
•Have your appliances checked regularly by a qualified
serviceman.
•Clean chimneys and flues yearly.
•Make regular visual inspections of all-fuel-burning
appliances.
•Check appliances for excessive rust and scaling.
•Do not barbecue indoors, or in attached garage.
•Open windows when a fireplace or wood burning stove is in
use.
•Be aware of CO poisoning symptoms.
DO NOT:
•Burn charcoal inside your home, RV, camper, tent or cabin
•Install, convert or service fuel burning appliances without proper
knowledge, skill and expertise
•Use a gas range, oven or clothes dryer for heating
•Operate unvented gas burning appliances using kerosene or
natural gas in closed room
•Operate gasoline powered engines indoors or in confined areas
•Ignore a safety device when it shuts an appliance off
•Ignore any warning from your CO alarm
END OF UNIT LIFE
With normal use the battery will last at least 10 years. However,
battery life will be reduced if the apparatus remains in alarm for
long periods of time.
The apparatus must be replaced when a fault warning signal is given.
NOTE: BATTERY SEALED-IN NOT FOR
REPLACEMENT
THIS PRODUCT CANNOT BE REPAIRED – IF THE UNIT IS
TAMPERED WITH IT WILL INVALIDATE THE GUARANTEE.
IF THE UNIT IS FAULTY PLEASE RETURN IT TO YOUR ORIGINAL
SUPPLIER WITH YOUR PROOF OF PURCHASE.
YOUR CO ALARM WARRANTY
Manufacturer:
Hispec Electrical Products Ltd
Unit 21 Chorley North Business Park
Chorley
Lancashire
PR6 7BX
www.hispec.co.uk
VER: Nov 2020
-
Deactivating Unit
These CO alarms are warranted to be free from defects in materials and
workmanship, under normal use and service, for a period of five (5) years
from date of purchase. Hispec will not be obligated to repair or replace
parts, which are found to be in need of repair due to misuse, damage, or
alterations occurring after the date of purchase. The liability of Hispec,
arising from the sale of this CO alarm, shall not in any case exceed the
cost of the purchase price of the CO alarm. In no case shall Hispec be
liable for personal injury, property damage, or any other consequential loss
or damage, resulting from the failure of the fire alarm.
CO alarms are not a substitute for property, life, or other insurance of any
kind.
This does not affect your statutory rights.
This alarm is suitable for private dwellings only and is not intended for
commercial or industrial dwellings.
Waste electrical products should not be disposed of with normal household
waste. Please recycle where facilities exist. Check with your Local
Authority or retailer for recycling advice. Regulations encourage the
recycling of Waste from Electrical and Electronic Equipment (European
"WEEE Directive" effective August 2005).
Important: The alarm will not silence if it has detected carbon
monoxide gas. (CO concentration higher than 30ppm). The
silence function is applicable only to the Low Battery Warning
Signal, End of Life Signal and Fault Warning signal.
To operate the silence feature, press the test button and hold for
approximately 3 seconds. The alarm unit will enter a dormant
period for 10 hours. After 10 hours, the CO alarm will resume its
operation. You should be alert to the signal the alarm gives and
replace the unit.
It is recommended that you test your CO alarm once a month to
ensure it is working correctly.
Test the unit by holding the Test / Silence button for 3 seconds. The
sounder will chirp 4 times and the red LED will flash for 30 seconds.
The unit will then enter back into normal operation mode.
Alarm unit Activation and Power on
After the CO Alarm is hooked on and installed, the green LED will flash
5 times. Then, the green LED will continuallyflash every 48 seconds
to indicate power is on.
High CO Concentration Warning
When the apparatus detects dangerous levels of CO gas, it will give an
alarm signal. The red LED will flash and the sounder will chirp 4 times
simultaneously every 5 seconds.
CO LEVEL (PPM) RESPONSE TIME (MIN)
50 60-90
100 10-40
300 < 3
WARNING
This product may not alarm at low carbon monoxide levels.
Individuals with medical problems may consider using warning
devices which provide audible signals for carbon monoxide
concentrations under 30 PPM.
Test / Hush Function
While the CO Alarm is chirping, press and hold the Test /
silence button for 2 seconds. If the CO alarm detects a CO
concentration under 30ppm, the alarm unit will be silenced for 10
hours. If the alarm unit did not silence, that means the CO Level
is higher than 30ppm. Read Section – “WHAT TO DO IF THE
ALARM SOUNDS”.
Low Battery Signal
In case the battery is at the end of its life, the apparatus will sound a short
chirp with a Yelllow LED flash simultaneously every minute. This low
voltage warning will be given for at least 7 days.
Under normal operating conditions, the batteries will last ten years.
End of Life Signal
After 10 years operation, the yellow LED will flash 3 times and beep 3
times simultaneously every 48 seconds. Read below “Deactivating Unit”.
Unit Malfunction
Your CO alarm performs an internal self-diagnosis every minute to make
sure that it is functioning properly. In the rare event that your alarm
malfunctions, the apparatus will sound a double short chirp and the
yellow LED will flash simultaneously every minute. In this case the alarm
must be replaced.
Never ignore a CO unit’s alarm. A true alarm is an indication of potentially
dangerous levels of carbon monoxide. CO alarms are designed to alert you
to the presence of carbon monoxide before an emergency, before most
people would experience symptoms of carbon monoxide poisoning, giving
you time to resolve the problem. Read section “What to do if alarm sounds”.
If the CO alarm is confirmed to be faulty or at the end of it’s life, you may
uninstall and deactivate the CO alarm by following these steps:
•Unhook the alarm unit from wall.
•Use a screwdriver to lever the deactivation clip out
•Fit the deactivation clip into the clip hole and push downward
•The alarm unit is now deactivated
TESTING YOUR CO ALARM
SILENCE FEATURE
WHAT TO DO IF THE ALARM SOUNDS
WARNING
Activation of your CO alarm indicates the presence of carbon
Monoxide (CO), which can KILL YOU.
If alarm signal sounds:
1. Immediately move tofresh air – outdoors or by an open
door/window. Do a head count to check that all persons are
accounted for.
2. Where possible turn off all fuelled appliances and stop using
them.
3. Call your emergency services if anybody is unwell or missing.
4. Do not re-enter the premises nor move away from the open
door/window until emergency services responders have arrived,
the premises have been aired out, and your alarm remains in its
normal condition.
5. Call a qualified appliance technician to investigate for sources
of CO from fuel burning equipment and appliances, and inspect
for proper operation of this equipment. If problems are identified
during this inspection have the equipment serviced immediately.
Note any combustion equipment not inspected by the technician
and consult the manufacturers’ instructions, or contact the
manufacturers directly, for more information about CO safety
and this equipment. Make sure that motor vehicles are not, and
have not been, operating in an attached garage or adjacent to
the residence.
MAINTAINING YOUR CO ALARM
Your alarm will alert you to potentially hazardous CO
concentrations in your home when maintained properly. To
maintain your alarm in proper working order, it is recommended
that you:
•Test your alarm at least once a month.
•Clean the outside case regularly to prevent dust or dirt build
up in the slots. DO NOT USE CLEANING AGENTS,
BLEACH, POLISH OR ANY CHEMICALS. Chemicals
can permanently damage or temporarily contaminate the
sensor. Simply wipe with a damp cloth OR a clean tissue.
•Do not paint the CO alarm
NOTE - If you will be staining or stripping wood floors or furniture,
painting, wall-papering, or using aerosols or adhesives, remove
the CO alarm to a remote location beforehand in order to prevent
possible damage to or contamination of the sensor.
The following is a list of substances which, at high levels, can
affect the sensor and may cause a nuisance alarm that is not a
carbon monoxide alarm.
Methane, propane, iso-butane, ethylene, ethanol, alcohol, iso-
propanol, benzene, toluene, ethyl acetate, hydrogen, hydrogen
sulfide, sulfur dioxides. Also most aerosol sprays, alcohol based
products, paints, solvents, adhesives, hair sprays, after shaves,
perfumes and some cleaning agents.
NOTE: THE APPARATUS SHALL NOT BE EXPOSED
TO DRIPPING OR SPLASHING.
SYMPTOMS OF CO POISONING
The following symptoms may be related to CO poisoning:
35 ppm The maximum allowable concentration for
continuous exposure for healthy adults in any
8 hour period.
200 ppm Slight headaches, fatigue, dizziness, nausea
after 2-3 hours
400 ppm Frontal headaches within 1-2 hours, life
threatening after 3 hours.
800 ppm Dizziness, nausea and convulsions within 45
minutes. Unconsciousness within 2 hours. Death
within 3 hours.
1600 ppm Headache, dizziness and nausea within 20
minutes. Death within 1 hour
6400 ppm Headache, dizziness and nausea within 1-2
minutes
The following symptoms are related to CARBON MONOXIDE
POISONING and are to be discussed with ALL members of the
household:
Mild Exposure: Slight headache, nausea, vomiting, fatigue (often
described as “flu-like” symptoms).
Medium Exposure: Severe throbbing headache, drowsiness,
confusion, fast heart rate.
Extreme Exposure: Unconsciousness, convulsions, cardio-
respiratory failure, death.
Many cases of reported CARBON MONOXIDE POISONING
indicate that while victims are aware they are not well, they
become so disoriented they are unable to save themselves by
leaving the building or calling for assistance. Young children and
household pets are typically the first affected.
The apparatus may not prevent the chronic effects of carbon
dioxide exposure and it will not fully safeguard individuals
at special risk.
IMPORTANT SAFEGUARDS
Installation of your CO alarm is only one step in your safety plan.
Educate yourself and familyto the sources and symptoms of CO
poisoning and how to use your carbon monoxide alarm:-
•Buy appliances approved by a recognized testing laboratory.
•Install the appliances properly, following the manufacturers’
instructions.
•Have installations done by professionals.
•Have your appliances checked regularly by a qualified
serviceman.
•Clean chimneys and flues yearly.
•Make regular visual inspections of all-fuel-burning
appliances.
•Check appliances for excessive rust and scaling.
•Do not barbecue indoors, or in attached garage.
•Open windows when a fireplace or wood burning stove is in
use.
•Be aware of CO poisoning symptoms.
DO NOT:
•Burn charcoal inside your home, RV, camper, tent or cabin
•Install, convert or service fuel burning appliances without proper
knowledge, skill and expertise
•Use a gas range, oven or clothes dryer for heating
•Operate unvented gas burning appliances using kerosene or
natural gas in closed room
•Operate gasoline powered engines indoors or in confined areas
•Ignore a safety device when it shuts an appliance off
•Ignore any warning from your CO alarm
END OF UNIT LIFE
With normal use the battery will last at least 10 years. However,
battery life will be reduced if the apparatus remains in alarm for
long periods of time.
The apparatus must be replaced when a fault warning signal is given.
NOTE: BATTERY SEALED-IN NOT FOR
REPLACEMENT
THIS PRODUCT CANNOT BE REPAIRED – IF THE UNIT IS
TAMPERED WITH IT WILL INVALIDATE THE GUARANTEE.
IF THE UNIT IS FAULTY PLEASE RETURN IT TO YOUR ORIGINAL
SUPPLIER WITH YOUR PROOF OF PURCHASE.
YOUR CO ALARM WARRANTY
Manufacturer:
Hispec Electrical Products Ltd
Unit 21 Chorley North Business Park
Chorley
Lancashire
PR6 7BX
www.hispec.co.uk
VER: Nov 2020
-
Deactivating Unit
These CO alarms are warranted to be free from defects in materials and
workmanship, under normal use and service, for a period of five (5) years
from date of purchase. Hispec will not be obligated to repair or replace
parts, which are found to be in need of repair due to misuse, damage, or
alterations occurring after the date of purchase. The liability of Hispec,
arising from the sale of this CO alarm, shall not in any case exceed the
cost of the purchase price of the CO alarm. In no case shall Hispec be
liable for personal injury, property damage, or any other consequential loss
or damage, resulting from the failure of the fire alarm.
CO alarms are not a substitute for property, life, or other insurance of any
kind.
This does not affect your statutory rights.
This alarm is suitable for private dwellings only and is not intended for
commercial or industrial dwellings.
Waste electrical products should not be disposed of with normal household
waste. Please recycle where facilities exist. Check with your Local
Authority or retailer for recycling advice. Regulations encourage the
recycling of Waste from Electrical and Electronic Equipment (European
"WEEE Directive" effective August 2005).
Important: The alarm will not silence if it has detected carbon
monoxide gas. (CO concentration higher than 30ppm). The
silence function is applicable only to the Low Battery Warning
Signal, End of Life Signal and Fault Warning signal.
To operate the silence feature, press the test button and hold for
approximately 3 seconds. The alarm unit will enter a dormant
period for 10 hours. After 10 hours, the CO alarm will resume its
operation. You should be alert to the signal the alarm gives and
replace the unit.
It is recommended that you test your CO alarm once a month to
ensure it is working correctly.
Test the unit by holding the Test / Silence button for 3 seconds. The
sounder will chirp 4 times and the red LED will flash for 30 seconds.
The unit will then enter back into normal operation mode.
Alarm unit Activation and Power on
After the CO Alarm is hooked on and installed, the green LED will flash
5 times. Then, the green LED will continuallyflash every 48 seconds
to indicate power is on.
High CO Concentration Warning
When the apparatus detects dangerous levels of CO gas, it will give an
alarm signal. The red LED will flash and the sounder will chirp 4 times
simultaneously every 5 seconds.
CO LEVEL (PPM) RESPONSE TIME (MIN)
50 60-90
100 10-40
300 < 3
WARNING
This product may not alarm at low carbon monoxide levels.
Individuals with medical problems may consider using warning
devices which provide audible signals for carbon monoxide
concentrations under 30 PPM.
Test / Hush Function
While the CO Alarm is chirping, press and hold the Test /
silence button for 2 seconds. If the CO alarm detects a CO
concentration under 30ppm, the alarm unit will be silenced for 10
hours. If the alarm unit did not silence, that means the CO Level
is higher than 30ppm. Read Section – “WHAT TO DO IF THE
ALARM SOUNDS”.
Low Battery Signal
In case the battery is at the end of its life, the apparatus will sound a short
chirp with a Yelllow LED flash simultaneously every minute.This low
voltage warning will be given for at least 7 days.
Under normal operating conditions, the batteries will last ten years.
End of Life Signal
After 10 years operation, the yellow LED will flash 3 times and beep 3
times simultaneously every 48 seconds. Read below “Deactivating Unit”.
Unit Malfunction
Your CO alarm performs an internal self-diagnosis every minute to make
sure that it is functioning properly. In the rare event that your alarm
malfunctions, the apparatus will sound a double short chirp and the
yellow LED will flash simultaneously every minute. In this case the alarm
must be replaced.
Never ignore a CO unit’s alarm. A true alarm is an indication of potentially
dangerous levels of carbon monoxide. CO alarms are designed to alert you
to the presence of carbon monoxide before an emergency, before most
people would experience symptoms of carbon monoxide poisoning, giving
you time to resolve the problem. Read section “What to do if alarm sounds”.
If the CO alarm is confirmed to be faulty or at the end of it’s life, you may
uninstall and deactivate the CO alarm by following these steps:
•Unhook the alarm unit from wall.
•Use a screwdriver to lever the deactivation clip out
•Fit the deactivation clip into the clip hole and push downward
•The alarm unit is now deactivated
TESTING YOUR CO ALARM
SILENCE FEATURE
WHAT TO DO IF THE ALARM SOUNDS
WARNING
Activation of your CO alarm indicates the presence of carbon
Monoxide (CO), which can KILL YOU.
If alarm signal sounds:
1. Immediately move tofresh air – outdoors or by an open
door/window. Do a head count to check that all persons are
accounted for.
2. Where possible turn off all fuelled appliances and stop using
them.
3. Call your emergency services if anybody is unwell or missing.
4. Do not re-enter the premises nor move away from the open
door/window until emergency services responders have arrived,
the premises have been aired out, and your alarm remains in its
normal condition.
5. Call a qualified appliance technician to investigate for sources
of CO from fuel burning equipment and appliances, and inspect
for proper operation of this equipment. If problems are identified
during this inspection have the equipment serviced immediately.
Note any combustion equipment not inspected by the technician
and consult the manufacturers’ instructions, or contact the
manufacturers directly, for more information about CO safety
and this equipment. Make sure that motor vehicles are not, and
have not been, operating in an attached garage or adjacent to
the residence.
MAINTAINING YOUR CO ALARM
Your alarm will alert you to potentially hazardous CO
concentrations in your home when maintained properly. To
maintain your alarm in proper working order, it is recommended
that you:
•Test your alarm at least once a month.
•Clean the outside case regularly to prevent dust or dirt build
up in the slots. DO NOT USE CLEANING AGENTS,
BLEACH, POLISH OR ANY CHEMICALS. Chemicals
can permanently damage or temporarily contaminate the
sensor. Simply wipe with a damp cloth OR a clean tissue.
•Do not paint the CO alarm
NOTE - If you will be staining or stripping wood floors or furniture,
painting, wall-papering, or using aerosols or adhesives, remove
the CO alarm to a remote location beforehand in order to prevent
possible damage to or contamination of the sensor.
The following is a list of substances which, at high levels, can
affect the sensor and may cause a nuisance alarm that is not a
carbon monoxide alarm.
Methane, propane, iso-butane, ethylene, ethanol, alcohol, iso-
propanol, benzene, toluene, ethyl acetate, hydrogen, hydrogen
sulfide, sulfur dioxides. Also most aerosol sprays, alcohol based
products, paints, solvents, adhesives, hair sprays, after shaves,
perfumes and some cleaning agents.
NOTE: THE APPARATUS SHALL NOT BE EXPOSED
TO DRIPPING OR SPLASHING.
SYMPTOMS OF CO POISONING
The following symptoms may be related to CO poisoning:
35 ppm The maximum allowable concentration for
continuous exposure for healthy adults in any
8 hour period.
200 ppm Slight headaches, fatigue, dizziness, nausea
after 2-3 hours
400 ppm Frontal headaches within 1-2 hours, life
threatening after 3 hours.
800 ppm Dizziness, nausea and convulsions within 45
minutes. Unconsciousness within 2 hours. Death
within 3 hours.
1600 ppm Headache, dizziness and nausea within 20
minutes. Death within 1 hour
6400 ppm Headache, dizziness and nausea within 1-2
minutes
The following symptoms are related to CARBON MONOXIDE
POISONING and are to be discussed with ALL members of the
household:
Mild Exposure: Slight headache, nausea, vomiting, fatigue (often
described as “flu-like” symptoms).
Medium Exposure: Severe throbbing headache, drowsiness,
confusion, fast heart rate.
Extreme Exposure: Unconsciousness, convulsions, cardio-
respiratory failure, death.
Many cases of reported CARBON MONOXIDE POISONING
indicate that while victims are aware they are not well, they
become so disoriented they are unable to save themselves by
leaving the building or calling for assistance. Young children and
household pets are typically the first affected.
The apparatus may not prevent the chronic effects of carbon
dioxide exposure and it will not fully safeguard individuals
at special risk.
IMPORTANT SAFEGUARDS
Installation of your CO alarm is only one step in your safety plan.
Educate yourself and familyto the sources and symptoms of CO
poisoning and how to use your carbon monoxide alarm:-
•Buy appliances approved by a recognized testing laboratory.
•Install the appliances properly, following the manufacturers’
instructions.
•Have installations done by professionals.
•Have your appliances checked regularly by a qualified
serviceman.
•Clean chimneys and flues yearly.
•Make regular visual inspections of all-fuel-burning
appliances.
•Check appliances for excessive rust and scaling.
•Do not barbecue indoors, or in attached garage.
•Open windows when a fireplace or wood burning stove is in
use.
•Be aware of CO poisoning symptoms.
DO NOT:
•Burn charcoal inside your home, RV, camper, tent or cabin
•Install, convert or service fuel burning appliances without proper
knowledge, skill and expertise
•Use a gas range, oven or clothes dryer for heating
•Operate unvented gas burning appliances using kerosene or
natural gas in closed room
•Operate gasoline powered engines indoors or in confined areas
•Ignore a safety device when it shuts an appliance off
•Ignore any warning from your CO alarm
END OF UNIT LIFE
With normal use the battery will last at least 10 years. However,
battery life will be reduced if the apparatus remains in alarm for
long periods of time.
The apparatus must be replaced when a fault warning signal is given.
NOTE: BATTERY SEALED-IN NOT FOR
REPLACEMENT
THIS PRODUCT CANNOT BE REPAIRED – IF THE UNIT IS
TAMPERED WITH IT WILL INVALIDATE THE GUARANTEE.
IF THE UNIT IS FAULTY PLEASE RETURN IT TO YOUR ORIGINAL
SUPPLIER WITH YOUR PROOF OF PURCHASE.
YOUR CO ALARM WARRANTY
Manufacturer:
Hispec Electrical Products Ltd
Unit 21 Chorley North Business Park
Chorley
Lancashire
PR6 7BX
www.hispec.co.uk
VER: Nov 2020
-
Deactivating Unit
These CO alarms are warranted to be free from defects in materials and
workmanship, under normal use and service, for a period of five (5) years
from date of purchase. Hispec will not be obligated to repair or replace
parts, which are found to be in need of repair due to misuse, damage, or
alterations occurring after the date of purchase. The liability of Hispec,
arising from the sale of this CO alarm, shall not in any case exceed the
cost of the purchase price of the CO alarm. In no case shall Hispec be
liable for personal injury, property damage, or any other consequential loss
or damage, resulting from the failure of the fire alarm.
CO alarms are not a substitute for property, life, or other insurance of any
kind.
This does not affect your statutory rights.
This alarm is suitable for private dwellings only and is not intended for
commercial or industrial dwellings.
Waste electrical products should not be disposed of with normal household
waste. Please recycle where facilities exist. Check with your Local
Authority or retailer for recycling advice. Regulations encourage the
recycling of Waste from Electrical and Electronic Equipment (European
"WEEE Directive" effective August 2005).
Important: The alarm will not silence if it has detected carbon
monoxide gas. (CO concentration higher than 30ppm). The
silence function is applicable only to the Low Battery Warning
Signal, End of Life Signal and Fault Warning signal.
To operate the silence feature, press the test button and hold for
approximately 3 seconds. The alarm unit will enter a dormant
period for 10 hours. After 10 hours, the CO alarm will resume its
operation. You should be alert to the signal the alarm gives and
replace the unit.
It is recommended that you test your CO alarm once a month to
ensure it is working correctly.
Test the unit by holding the Test / Silence button for 3 seconds. The
sounder will chirp 4 times and the red LED will flash for 30 seconds.
The unit will then enter back into normal operation mode.
Table of contents
Other Hi-Spec Carbon Monoxide Alarm manuals
