HIGHLEAD GC24608-2 Instruction Manual

HIGH LEAD
Purchasing Dept
Copy
GC24608-2/GC24608-1L/1R
2-Needle/1-Needle,Post-Bed Compound-feed
Lockstitch Industrial Sewing Machine .
Instruction Manual
Parts Catalog
SHANGHAI HUIGONG N0.3 SEWING MACHINE FACTORY
From the library of: Superior Sewing Machine & Supply LLC

---CONTENTS---
Instruction Manual
• Preparation for operation .............................................................. 1
1, Safety precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
2, Precautions before starting operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
3, Precautions for operating conditions ....................................................... 1
• Cautions on use ...................................................................... 1
1, Lubrication ( 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
2, Lubrication (2) ........................................................................ 1
3, Condition of oil lubrication .............................................................. 1
4, Cautions on operation .................................................................. 2
• Operation ........................................................................... 2
1, How to attach needle ................................................................... 2
2, How to wind the lower thread ........................................................... 2
3, Selection ofThread .................................................................... 3
4, How to route the upper thread ............................................................ 3
5, Adjustment of stitch length and reverse sewing ............................................... 4
6, Setting bobbin ........................................................................ 4
7, Threading ofbobbin thread .............................................................. 4
8, Balance of thread tension ................................................................ 4
9, Lower thread tension ................................................................... 4
10, Upper thread tension .................................................................. 4
11, Adjustment of pressure of presser foot .................................................... 5
12, Timing between rotating hook motion and needle motion ...................................... 5
13, AdjustmentofFeeddogheight .......................................................... 5
14, Walking foot and presser foot vertical stroke adjustment ...................................... 6
15, Safety clutch device ................................................................... 6
16, Installation ofBelt cover ............................................................... 7
Specifications
............................................................................ 7
Parts Catalog
A, ARM BED AND ITS ACCESSORIES ..................................................... 8
B, THREAD TENSION REGULATOR MECHANISM ......................................... 10
From the library of: Superior Sewing Machine & Supply LLC

C, ARM SHAFT MECHANISM ........................................................... 13
D, UPPER SHAFT & PRESSER FOOT MECHANISM ......................................... 15
E, TAKE-UP THREAD AND SHAFT MECHANISM .......................................... 18
F, STITCH REGULATOR MECHANISM ................................................... 21
G, LOWER SHAFT & FEED ROCK SHAFT MECHANISM .................................... 23
H, HOOK SADDLE MECHANISM ........................................................ 26
L OIL LUBRICATION MECHANISM ..................................................... 30
J, ACCESSORIES ...................................................................... 33
From the library of: Superior Sewing Machine & Supply LLC

• Preparation for operation:
1. Safety precautions:
1) When turning the power on, keep your hands and fingers away from the area around/under the needle
and the area around the pulley.
2) Power must be turned offwhen the machine is not in use, or when the operator leaves the seat.
3) Power must be ttm1ed off when tilting the machine head, installing or removing the "V" belt, adjusting
the machine, or when replacing.
4) Avoid placing fingers, hairs, bars etc. near the pulley, "V" belt, bobbin winder pulley, or motor when the
machine is in operation.
5) Do not insert fingers into the thread take-up cover, under/around the needle, or pulley when the machine
is in operation.
6) If a belt cover, finger guard, eye guard are installed, do not operate the machine without these safety
devices.
2. Precautions before starting operation:
I) Never operate the machine before filling the machine's oil pan.
2) When a new sewing machine is first turned on, verify the rotational direction of the pulley with the
power on.
3) Verify the voltage and phase (single or three) with those given on the machine nameplate.
3. Precautions for operating conditions:
1) Avoid using the machine at abnormally high temperatures (35 "C or higher) or low temperatures (5 "C or
lower) .
2) Avoid using the machine in dusty conditions.
• Cautions on use:
1. Lubrication (1) (Fig.l)
Pour oil up to position "H" of the oil tank.
During operation, check the oil level periodically, and in cases
where the oil level is below position "L", replenish the oil supply up to
position "H''.
Usc white spindle oil.
2. Lubrication (2) (Fig.2a, Fig.2b)
When a new sewing machine is used for the first
time, or sewing machine left out of use for a long time is
used again, replenish a suitable amount of oil to the
portions indicated by arrow in the fig.
Note: Lubricate the Hook Base everyday.
3. Condition of oil lubrication (Fig.3):
-1-
From the library of: Superior Sewing Machine & Supply LLC

While operating the machine, check the condition of oil lubrication through the oil check window.
4. Cautions on operation
1) When the power is turned on or off, keep foot away from the pedal.
2) It should be noted that the brake might not work when the power is interrupted or power failure occurs during
sewing machine operation.
3) Periodically clean the machine.
II Operation
1. How to attach needle (Fig.4):
Note: Before attach needle, be sure to turn off the power.
1) Turn the balance wheel by hand to raise the needle bar to its highest
position;
2) Loosen the needle clamping screw:
3) Hold the needles so that the two needles side with the long grooved
(faces each other), and insert it as deeply as it will go into the needle
clamping holes( model GC24608-2);Hold the needle to its side with
the long groove side(left),then insert the needle as deeply as it will go
into the needle clamping hole(model GC24608-1L/R).
4) Tighten the needle clamping screw.
2. How to wind the lower thread (Fig.5):
Modt>l GC:l460~-:l
Model GC24608·1
Strength of winding: Particularly in the case of nylon or polyester thread, wind the bobbin loosely.
Uneven winding: If the bobbin is wound unevenly, slide the thread guide toward the less wound portion of
bobbin.
Winding amount: When the bobbin is wound excessively, loosen the adjusting screw. When the bobbin is wound
-2-
From the library of: Superior Sewing Machine & Supply LLC

insufficiently, tighten the adjusting screw.
0
Fig.6
3. Selection of Thread (Fig.6) :
It is recommended to use "S" twist thread in the left needle (Viewed from front), and "Z" twist thread in the
right needle.
When discriminate
use of needle thread is impossible, use "Z" twist thread in the needle. For bobbin thread,
"S" twist thread as well as "Z" twist thread can be used.
4. How to route the upper thread (Fig.7, Fig.8):
1) Pass each upper thread through thread guide A
Note: when thin slippery thread (polyester thread for example) is used pass the thread through thread
guide B
as show in Fig.7
2) With the take-up lever located at the upper mostposition, pass each thread in the order in Fig.8.
Note: Pressing the upper thread loosening button, the upper
thread can be pulled out easily.
A B A B A Needle thread
tension releasing button
Lead the Lead the
thread thread
leftward rightward
-3-
Fig.8
From the library of: Superior Sewing Machine & Supply LLC

5. Adjustment ofstitch length and reverse sewing (Fig.9):
1) Rotate the stitch length adjusting dial to change the stitch length
2) Pressing the stitch length adjusting lever for reverse stitching.
6. Setting bobbin ( Fig.lO ):
1) Pulling out 5cm thread tail from the bobbin;
2) Hold the bobbin so that the bobbin thread is would
in tight direction and put it into the hook.
7. Threading of bobbin thread (Fig.U, Fig.l2):
I) Flap down the latch lever, from the slit 1 of the hook, pass the thread through underneath of the hook
body
2, pull the thread outside (Fig.ll );
2) While holding the needle thread
by left hand, rotate the hand wheel one turn by right hand. By pulling
up the needle thread, the bobbin thread will be lifted. Close the slide plate (Fig.l2)
AQ.-s?~ m?
Balance tension
C X ..,::::> ____.- ~
fu~Ma::ugm
bobbin ten.--Gio_;_n ----1
Fig.l3
8. Balance of thread tension (Fig.13):
9. Lower thread tension (Fig.l4):
There is virtually no need to adjust the lower thread tension, except for special kind of the fabrics or thread,
when slight adjustment will be necessary.
Turning the screw 1 clockwise will increase the tension
of lower thread, otherwise, the tension of lower
thread will decrease. (Fig.l4).
10-. Upper thread tension (Fig.l5):
-4-
From the library of: Superior Sewing Machine & Supply LLC

1) The upper thread can be adjusted based on the lower thread
tension.
2) Adjustment can be done by rotating the thread tension nut.
11. Adjustment of pressure of presser foot
(Fig.16):
1) Pressure should be adjusted according to the material to be
sewn.
2) Turning the pressure a4iusting screw to adjust the
pressure
of presser foot
12. Timing between rotating hook motion
and needle motion (Fig.17):
1) Set stitch length to ''6";
2) When needle is lifted 2.4mm from the lower dead
point, the following position relationship should be
maintained:
• The upper edge of needle eye should be 2.3mm
below the hook point
• The hook point should be located at the center of needle
aXIS.
• Gap between the hook point and the side face of needle
should be 0.05 mm
13. Adjustment of Feed dog height (Fig.18):
Height of feed dog should be adjusted for individual fabrics with
the following cautions:
1) Fabric will be damaged if the feed dog extends too high or
pressure
of presser foot is too large
2) Even stitch length cannot be assured if the feed dog is too
low or pressure
of presser foot is too small
Figl5
Gap between hook point and upper edge of
needle eye
L_~
~~:~~~:~
needle lower
dead poinl
Center of
needle axis
3) Feed dog height should be measured at the point where the needle is at
7
~0.8mm
the top position
For light fabric: Approx 0.8mm
For usual fabric: Approx l.Omm
For heavy fabric: Approx 1.2mm
Adjustment procedure:
I) Lay down the machine bed toward the other side;
2) Turn the balance wheel by hand stop when the feed dog is raise to its
highest position from the surface
of needle place;
3) Loosen the Screw and adjust the height
of the feed dog;
-5-
~ 11.0mm
721 at,
~"'I 12mm
IFig.18
From the library of: Superior Sewing Machine & Supply LLC

4) After adjusted, tighten the screw.
The feed dog height is factory-adjusted to 1.2mm
14. Walking foot and presser foot vertical stroke adjustment (Fig.19):
When fabric with large elasticity is sewn, or when thickness of
fabric changes, the vertical stroke (movable range) of the presser
feet should be adjusted
as follows: Special bolt Crank
1) Loosen the special bolt;
2) The vertical strokes
of presser feet become maximum when
the crank rod is moved downward and set;
3) The vertical strokes
of presser feet become minimum when
the crank rod is moved upward and set;
4) After the adjustment, tighten the special nut.
The vertical strokes of presser feet can be adjusted within a
range from 2mm to 6mm.
15. Safety clutch device (Fig.20, Fig.21)
Crank rod
Safety clutch device is installed to prevent the hook and cog belt from damage in case the
thread
is caught into the hook when the machine is loaded abnormally operation.
1) Function of safety clutch:
A. When the safety clutch acts, the cog belt pulley will be unloaded. Then the rotation of hook shaft will
stop. The arm shaft only will rotate. Stop the operation
of machine.
B. Clean the thread thoroughly which is caught into the hook.
C. Turn the cog belt hub by hand, and check whether the hook shaft rotates lightly and properly, place the
clutch device
as follows.
2) How to set
the safety clutch (Fig.20)
Push
bt1tton
Fig.20
While mark
Timing BeH
EccanlricPin ~;j
Strengthen , Set Screw - • •
" ) -
Weaken • -
., :--_ (
Low Shaft
Eccentric Pinr-----1
Fig.21
A. While pressing down the push button on the opposite side of bed by left hand, turn the balance wheel
slowly by right hand away from you;
B. The balance wheel will stop by the gear plate, but turn the balance wheel more firmly;
C. Release the push button, the safety clutch device is set.
3) Force applied
to the safety clutch (Fig.21)
A. The force applied to the safety clutch is the smallest when the mark of eccentric pin faces the center of
the lower shaft. The force proportionally increases as the mark faces the outside;
B. To adjust the force slide the tinting belt, loosen the set screw, and turn the eccentric pin;
C. After the adjustment, tighten the set screw.
-6-
From the library of: Superior Sewing Machine & Supply LLC

16. Installation of Belt cover (Fig.22 ):
Set the screv•s ( 4, 6 ) and the washer ( 7) on the arm as illustrated. Assemble the belt guard 3 in the
direction
of the arrow , tighten its screw. The assembling of the belt guard 5 is the same as the belt guard 3, then,
insert the belt guard l from the top of the pulley into the inside of the 3 and 5, tighten the screws ( 2 ) .
Fig.22
Specifications:
~
GS24608-2 GC24608-lLIR
c
Material weight Medium Heavy material
Max. sewing speed 2000rpm
Stitch length 0-7mm
Needle bar stroke 36mm
Presser By hand 8mm
foot stroke By knee 16mm
Alternating movement 2-6mm
Stitch-length adjusting Dial type
Alternating movement Automatic
Needle
DPX 17 (22#--24#)
Motor Clutch motor 370W
Needle gauge 7.94mm 9.52mm
-7-
From the library of: Superior Sewing Machine & Supply LLC

A.ARM BED AND ITS ACCESSORIES
25
24
20
2 3 4
(2)
5 6
19 18 (15) 17 16 15 14 13
-8-
8 9 10
11
I
From the library of: Superior Sewing Machine & Supply LLC

A.ARM BED AND ITS ACCESSORIES
N
.....:1
p::
I --
00
I I
Fig. 0
00 00
Part No. Description
\D
0 0 Remarks
""'"
\D \D
No. N
""'"
""'"
u N N
u u
0 0 0
AOl HA300B2090 Rubber plug 2 2 2
A02 HA300B2170 Screw 30 30 30 11/64 (40) x9
A03 H4716B8001 Oil guide plate 1 1 1
A04 H4717B8001 Thread take-up cover 1 1 1
AOS H4715B8001 Rubber plug 1 1 1
A06 H4718B8001 Arm side cover (left) 1 1 1
A07 H2000B2010 Rubber plug 1 1 1
A08 H4719B8001 Arm side cover (right) 1 1 1
A09 HA700B2060 Screw 2 2 2 11/64 (
40) xs
AlO H2400B2100 Thread guide 1 1 1
All HA307B0673 Rubber plug 1 1 1
A12 H4715H8001 Push button 1 1 1
Al3
H4714H8001 Spring 1 1 1
Al4 H007013050 E-type ring 1 1 1
Al5 H2000M0080 Cap 2 2 2
Al6 H3200B2100 Screw 1 1 1 9/64 (40)
x6.5
Al7 H321280066 Thread guide 1 1 1
Al8
H3000D2160 Screw 1 1 1 9/64 (
40) x4. S
:\19
H4726B8001 Thread guide 1 1 1
A20 H4727B8001 Face plate 1 1 1
A21
H2400B2080 Screw 2 2 2 3/16
(28) x12.1
A22 H2400B2070 Thread guide 1 1 I
A23 H4730B8001 Guide mounting ple1te
1 1 I
A24 H2400B2060 Spacer 1 1 1
~
A25 I-!320082060 Oil guide plate 1 1 I
-9-
From the library of: Superior Sewing Machine & Supply LLC

B. THREAD TENSION REGULATOR MECHANISM
1 2 3 4 8 9 10 11 12 13 14 15 16 17 18
-----------------------20
------------21
~~h 22
48 47 46 45 44 43 42 41 40 39 38 37 36 35
-10-
~~----23
34 33 32 31 30
24
25
26
27
28
29
From the library of: Superior Sewing Machine & Supply LLC

B.THREAD TENSION REGULATOR MECHANISM
N
.....l IX
I --
00
I I
Fig. 0
00
00
Part No. Description
\0
0 0 Remarks
""'"
\0 \0
No. N
""'" ""'"
u N N
u u
0 0 0
BOl
H2504C6510 Screw 2 2 2 9/64
(40) X3
B02 H3221B3142 Tension releasing plate 1 1 1
B03 H3221B6812 Tension releasing spring 1 1 1
B04 H4705C8001 Screw 1 1 1
B05 H4706C8001 Lever 1 1 1
B06 HA7311C306 Screw 1 1 1
9164 (40) x7
B07 H4707C8001 Mounting plate 1 1 1
B08 H007013050 E-type ring 1 1 1
B09 H3221B6820 Mounting plate 1 1 1
BlO HA300C2030 Screw 2 2 2
11164 (40) x8
Bll H3221B6810 Nut 2 2 2
Bl2
H4708C8001 Spring 1 1 1
Bl3
H4709C8001 Push button 1 1 1
Bl4 H3221B0685 Thread tension stud 1
11164
(40)
xl4
Bl5 H3221B0683 Thread tension stud 1 1 1
11164 (40)
Xl4
Bl6 HA112B0693 Thread tension disc 4 2 2
Bl7
H3300B2040 Spring 2 1 1
Bl8 HA710B0671 Thumb nut 2 1 1
Bl9 H3221B0682 Pin 3 2 2
B20 HA106B0676 Screw I 1 I 9/64
(40) x6
B21
H3306B0661 Thread guide 1 1 1
B22 HA310B0702 Tension releasing disc 2 1 I
B23 H4710C8001 Spring 2 1 I
B24
HAII5B7010 Thumb nut revolution stopper 2 1 1
B25 HA310B0701 Thumb nut 2 1 I
B26 HA310B0705 Thread tension disc 4 2 2
B27 H3221B6816 Pin 1
B28 H3221B0689 Thread tension stud 1 1/4
(40)
x23
B29 H3221B0686 Thread tension stud I 1 1
114
(40)
X23
B30 H32481B721 Thumb nut 1 1 1
B31 H32481B621 Take-up spring guide I
B32 H32481BC21 Screw I 9/64
(40) x6
B33 H32481BB21 Stopper 1
B34 H32481B921 Tirread tension post I
B35 H32481B521 Screw 2 1/8
(44) x3.9
B36 H32481B821 Bushing I
B37 H32481BF21 Plate complete I
B38 H4712C8001 Thread take-up spring I
B39 H32481BE21 Plate complete 1
B40 H4713C8001 Thread take-up spring I 1 I
B41 H32481BD21 Plate complete 1 1 I
B42 H32481B421 Thread tension stud I 9/64
(40)
X2.9
B42 H4804C8001 Thread tension stud 1 1 9/64
(40)
x2.9
-11-
From the library of: Superior Sewing Machine & Supply LLC

B. THREAD TENSION REGULATOR MECHANISM
N
.....l
~
I
......
-
00
I I
Fig. 0
00
00
Part No. Description '-0 0 0 Remarks
..r
\0
'-0
No. N
-.:!"
..r
u N N
u u
(j
0
(j
843 H324818121 Thread tension stud 1
114 (40) x38.5
843 H4805C8001 Thread tension stud 1 1 1/4
(40) x14.5
844 H3230K0751 Screw 1 1 1 11/64
(40) XlQ
845 H322186817 Pin 1 1 1
846 H4769E8001 Pin 1 1 1
847 H3200B2100 Screw 1 1 1 9/64 (
40) x6.5
848 H322186819
Stopper 1 1 1
-12-
From the library of: Superior Sewing Machine & Supply LLC

C.ARM SHAFT MECHANISM
-13-
(10) 31 30 29 28 27 26
18
19
20
From the library of: Superior Sewing Machine & Supply LLC

C.ARM SHAFT MECHANISM
N
.....l
~
I
,....,
-
00
I I
Fig. 0
00 00
Part No. Description
\D
0 0 Remarks
"i"
\D
\D
No. N
"i"
"i"
u N N
u u
Cl
Cl Cl
COl HA307C0662 Set screw 1 1 1 114 (40)
X6
C02 H4706D8001 Crank 1 1 1
C03 HA105D0662 Set screw 1 1 1 114 (40)
x4
C04 HAIOOC2060 Screw 1 1 1 9/32
(28) xi3
cos HAIOOC2070 Screw 1 1 1 9/32 (
28 ) X 14
C06 H4708D8001 Set screw 1 1 1 114(24)x13
C07 H32111Bl04 Felt 1 1 1
C08 H32111B204 Arm shaft bushing (left) 1 1 1
C09 H4709D8001 Arm shaft 1 1 1
CIO H3205C0661 Spring flange 3 3 3
Cll HA113F0684 Screw 1 1 1 15/64 (28)
X8.5
C12 H3205Cl021 Pulley 1 1 1
C13 HAIOOF2130 Screw 1 1 1 15/64
(28)
X!4.5
C14 H3205J0662 Bearing 1 1 1
C15 H3205J0661 Collar 1 1 1
C16 HA110D0672 Screw 2 2 2 15/64
(28) x12
C17 H4100C2040 Pulley 1 1 1
C18 H6304C8001 Cog belt 1 1 1
C19 HA104F0654 Screw 1 1 1 15/64
(28) XlO
C20 H4713D8001 Link 1 1 1
C21
H4714D8001 Pin 1 1 1
C22 H4716D8001 Spring 1 1 1
C23 H007013025 E-type ring 1 1 1
C24 H4717D8001 Link 1 1 1
C25 H4718D8001 Pin 1 1 1
C26 H4719D8001 Link 1 1 1
C27 H4715D8001 Pin 1 1 1
C28 H4720D8001 Bushing 1 1 1
C29 H4721D8001 Screw 1 1 1 15/64(28)X10.5
C30 H4722D8001 Pulley 1 1 1
C31
H4723D8001 Screw 2 2 2 15/64(28)x4.5
-14-
From the library of: Superior Sewing Machine & Supply LLC

D. UPPER SHAFT & PRESSER FOOT MECHANISM
40
39
38
37
1 2 3 4 (2) 5 6 7 8 9 10 11 12 13 14
29
-15-
18
From the library of: Superior Sewing Machine & Supply LLC

D. UPPER SHAFT & PRESSER FOOT MECHANISM
N
......:!
0:::
I --
00
I I
Fig. 0
00
00
Part No. Description
'D
0 0 Remarks
""'"
'D
'D
No. N
""'"
""'" u N N
u u
0 0 0
DOl H4705E8001 Feed lifting rock shaft 1 1 1
D02 H4707E8001 Bushing 2 2 2
D03 H003055060 Nut 1 1 1 (M6x0.75)
D04 H4706E8001 Set screw 2 2 2
1/4 (24)X7
DOS
H4709E8001 Crank I 1 1
D06 H3115F0671 Screw 1 1 1 1/4
(28) x16
D07 H2013J0065 Washer 1 1 1
D08 H2014J0066 Connecting rod 1 1 1
D09 H2000J2100 Screw 1 1 1
DlO H4713E8001 Oil wick 1 1 1
D11 H20111Cl06 Holder 1 1 1
Dl2 H007009250 C-type ring 1 1 I
D13 H4714E8001 Eccentric 1 1 1
D14 HA307C0662 Screw 2 2 2
114 (40) X6
D15 H4732E8001 Screw I 1 1 1/4
(24)
xJ4
D16 H4739E8001 Snap pin 1 1 1
Dl7
H4734E7101 Knee lifter lifting lever 1 1 1
D18 H0204E8001 Operation rod 1 1 1
Dl9
H4741E8001 Collar 1 1 1
D20 H4742E8001 Screw 1 1 1
11164 (40) x5.5
D21
H3100G2170 Screw 1 1 1
114 (24) xJ7
D22 H4730E8001 Lever spring I I I
D23 H4729E8001 Screw I I I 15/64 (
28) x79
D24 H4727E8001 Twist spring 1 I I
D25 H4728E8001 Knee lifting lever I I I
D26 H3100G2130 Screw I 1 I 1/4
(24) x7
D27 H4726E8001 Nut I I 1
D28 H4725E8001 Screw I I I 1/4
(24)
Xj9
D29
HAIIIG0683 Screw 2 2 2 11164(40)x
12
D30 H4723E8001 Guide I I I
D31
H4754E8001 Presser bar I I I
D32 H4744E8001 Bushing I I I
D33 H3200E2020 Screw I I I l/8(44)x9
D34 H4746E8001 Spring bracket I I I
D35 H4768E8001 Thread releasing plate I 1 I
D36 H2404I0034 Screw I I I 9/64
(40) x8.5
D37 H4748E8001 Lift lever I I I
D38 H4767E8001 Spring I I I
D39 H4752E8001 Bracket I I I
D40 H4749E8001 Screw I I I
ll/64 (40) x8.5
D41 H4715E8001 Bell crank I I I
D42 H2004J0655 Screw I I I 3/16
(28) xiO
D43 H4717E8001 Roller I I I
-16-
From the library of: Superior Sewing Machine & Supply LLC

D.UPPER SHAFT & PRESSER FOOT MECHANISM
C"l
.....l
~
I --
00
I I
Fig. 0
00 00
Part No. Description
I.D
0 0 Remarks
-.:!"
I.D I.D
No. C"l
-.:!"
-.:!"
u C"l C"l
u u
0 0 0
D44 H4718E8001 Screw 1 1 1
ll/64(32)x6
D45 H2004J0662 Screw 1 1 1 1!4(40)x5
D46 H4719E8001 Link 1 1 1
D47 HA100E2150 Screw 2 2 2 11/64
(40)
x10
D48 H4722E8001 Washer 2 2 2
D49 H4721E8001 Bell crank guide 1 1 1
DSO H4753E8001 Screw 1 1 1
11164 (40)
x17.5
D51 H4708D8001 Set screw 2 2 2
1/4(2LI)x 13
D52 H3100G2110 Lifting presser 1
D52 HF504E8001 Lifting presser 1
D52 H4762E8001 Lifting presser 1 3/8
D52 H4761E8001 Lifting presser 1 5/16
D53 HE013N8001 Finger gusrd 1
D53 HE204I8001 Finger gusrd 1 1
-17-
From the library of: Superior Sewing Machine & Supply LLC