Hiwin PNED Series User manual

PMED-H1-1 VER1.0(A-0)
1
PMED-H1-1
VER1.0(A-0)

PMED-H1-1 VER1.0(A-0)
26

PMED-H1-1-Series
User’s Manual
Table of Contents
1. Functions 27
2. Specifications 27
3. Panel Description 28
4. Normal Mode Description 28
5. Function Mode Description 29
6. Auto-Center (1/2) Function 30
7. Count Direction Setting (DIR) 31
8. Input Signal Setting (ADC) 32
9. Decimal Point Setting (DOT) 33
10. Resolution Setting (DPI) 35
11. Pre-Call (PCALL) 36
12. Preset Setting (PSET) 38
13. Relay Enable/Disable Setting (IO.USE) 40
14. Relay Output Position Setting (IO.SET) 42
15. Software Version 44
16. Description of Input Signal 44
17. Description of RS-232 Signal 45
18. Description of Output Signal 46
19. Dimensions 47
20. Parameter Defaults 48

PMED-H1-1 VER1.0(A-0)
27
21. Appendix 49
1. Functions:
(1) Switch between ABS and REL: See appendix
(2) Units of measurement: mm/inch
(3) Zero and auto-center (1/2) function
(4) Set count direction (increase/decrease)
(5) Switch between digital and analog signals
* Analog signal is only used for the HIWIN Positioning Measurement System
(6) Decimal point setting
mm: 0.001, 0.01, 0.1, 1
inch: 0.000001, 0.00001, 0.0001, 0.001
(7) Resolution setting (unit: m): 1, 2, 5, 10
(8) Preset function: 8 sets
(9) Relay output function: 4 sets
(10) Current value read (displayed)
will be automatically saved during a temporary
power failure
2. Specifications:
1Display: LED 8 digit display
1Input power: 5VDC±5%/1A
1Input signal: SIN/COS 1Vp-p(analog), 5V RS-422/TTL(digital)
1Relay contact rating: 24VDC/2A
1Relay frequency: 2 seconds
1Operating temperature range: 02~ +502
1Storage temperature range: -52~ +652

PMED-H1-1 VER1.0(A-0)
28
3. Panel Description:
ABS: ABS Mode
INC: REL Mode
MM: Unit: mm
INCH: Unit: inch
4. Normal Mode Description:
Button representation:
Menu
Switch between ABS/REL mode
Switch between units (mm/inch)
Set zero mark

PMED-H1-1 VER1.0(A-0)
29
5. Function Mode Description:
When the display is set on normal mode, press the MENU button to enter into the
function mode
Button representation:
Return back to normal mode/back one page
Switch between functions
Switch between functions
Confirmation button
F1-1-2>F2-DIR>F3-ADC>F4-DOT>F5-DPI>F6-PCALL>
F7-PSET>F8-IO.USE>F9-IO.SET> F1-1-2
F1-1-2> F9-IO.SET> F8-IO.USE> >F7-PSET
>F6-PCALL>F5-DPI >F4-DOT>F3-ADC>F2-DIR> F1-1-2

PMED-H1-1 VER1.0(A-0)
30
6. Auto-Center (1/2) Function:
Function: To set the auto-center (1/2) value when needed
Caution: Can only be used when the display unit is set on INC mode
Step 1. If not in INC mode, press
to switch into INC mode
Step 2. Press once, and then
press
or until it
displays F1-1-2
Press to find the
midpoint

PMED-H1-1 VER1.0(A-0)
31
7. Count Direction Setting (DIR):
Function: To set the direction (increase or decrease)
Note: Can be used with the display unit set on ABS mode or INC mode
Step 1. Press once, and then
press or
until it displays F2-DIR
Step 2. Press to enter setting,
then press or
to choose the counting direction
(positive or negative)
Press to confirm

PMED-H1-1 VER1.0(A-0)
32
8. Input Signal Setting (ADC):
Function: Choose the input signal (analog or digital)
Note: Can be used with the display unit set on ABS mode or INC mode
Step 1. Press once, then
press or
until it displays F3-ADC
Step 2. Press to enter setting,
then press or
to choose DIG (digital signal) or
ANA (analog signal)
Press to confirm

PMED-H1-1 VER1.0(A-0)
33
9. Decimal Point Setting (DOT):
Function: To set the decimal point according to the user’s requirement
1. For mm, choices are 0.001, 0.01, 0.1, 1
2. For inch, choices are 0.000001, 0.00001, 0.0001, 0.001
Note: Can be used with the display unit set on ABS mode or INC mode
Step 1. Press to choose the
desired unit
Step 2. Press once, and then press
or until it
displays F4-DOT

PMED-H1-1 VER1.0(A-0)
34
Step 3. Press to enter setting, then
press or to choose
the placement of the decimal point
Press to confirm