scope of this manual, consult a professional.
● Do not use this product if unusual occurrences
should occur. Consult with your dealer immediately.
● If any unusual noise, scents, and/or vibrations are
noticed, stop using the product to prevent a fire
and/or short circuit.
● Do not try to repair the product yourself.
Consult with your dealer.
Caution
Red LED
Green LED
Red LED :
Illuminated: Select Device is OK
Flashing: Select Device Error
（Please check pairing settings）
Green LED :
Illuminated: Select Cartype is OK
Flashing: Select Cartype Error
If the OB-LINK TYPE-001 is connected to the OBD II
port and Device setup and vehicle protocol type are
not set correctly. OB-LINK TYPE-001 will switch off
after 2 minutes. When resetting, please unplug from
the OBD II port and restart connection process.
Use the included hook and loop tape to secure the
OB-LINK TYPE-001 unit in a location which will not
obstruct driving.
7.Fixing OB-LINK TYPE-001
● OB-LINK TYPE-001 will automatically switch ON
when it detects that the application and engine
are started (ECU power ON)
If the engine is stopped (ECU Power OFF),
Bluetooth connection is lost or the application is
closed, OB-LINK TYPE-001 will automatically
switch off.
● If an engine related problem is detected, An
Error code is displayed. If you see this please
consult an HKS Pro Shop or specialist.
② Select Cartype
Tap Cartype select on setting menu.
From “OB-LINK car application list” you can
download from HKS site,select Cartype according
to your car OB-LINK TYPE-001 attached.
(HKS web address in section1)
If ① and ② are set correctly, the OB-LINK TYPE-001
LED will illuminate as follows:
● Do not use this product if any unusual noises or
scents are detected.
Consult your Authorized HKS Dealer immediately.
Otherwise, it may cause electric shock or fire.
WARNING
Maintenance
5. The check of IG signal line
To let OB-LINK TYPE-001 reflect OBD meter,
connection of IG signal line is required. There are
vehicles which have IG signal line in an OBDⅡ
coupler. In that case, connection of IG signal wire is
unnecessary.
Please check IG signal line by the method of ① or ②.
① Check a connection status by the OBDⅡ coupler.
As with the illustration, check whether a terminal
has been inserted at the edge of upper right.
Caution
● Please ensure that OB-LINK TYPE-001 or the wiring
does not contact with water.
If OB-LINK TYPE-001 or its wiring contact water,
there may be problems with operation and could
possible cause damage to OB-LINK TYPE-001 or the
vehicle.
● If it is being unused for long periods (over 2weeks)
please disconnect the OB-LINK TYPE-001 as it can
lead to battery drain.The current draw during
standby is approximately 0.2[mA].
IG signal line
Case 1. In the event that the terminal has been
inserted,it has the IG signal line.
Case 2. If it's none, it doesn't have the IG signal line.
② Check a connection status by the application,
“CarscopePlus” .
Run CarscopePlus and tap it in order of setting” ,
"Check of the IG signal line".
Case 1. If a message “IG signal line is OK” is
displayed, it has the ignition signal line.
Case 2. If a message “IG signal line is NG” is
displayed, it doesnʼ t have the ignition
signal line.
Connect the Ignition signal line if Ignition signal line
isn't in the OBD2 coupler. (Refer to Article 6)
6. Connection of IG signal wire
Splice to
the IG line
① Connect the Redwire of the IG signal-Pick-up
harness to the Red wire of the OB-LINK
TYPE-001.
② Splice these to the line that outputs 12V while IG
is on.(like a power line of a cigar socket)
IG signal-Pick-up
harness
Installing Splices
Strip5mmofcover
Stakethewires
usingasplice
Insulatewithelectricaltape
Twin wires
together
