Home Comfort HCWP1605 User manual

Dimensions
W545mm D575mm H944mm
Weight
Rated voltage and frequency
Model
Water level/water volume about
Inlet pressure
120V~ 60Hz
0.03MPa~0.85MPa
Specification
17
HCWP1605
Rated input power Wash 420W spin 340W
About 37kg
7.0kg (dry laundries weight)
Rated capacity of wash and spin
10/66L 9/62L 8/58L 7/54L
6/50L 5/46L 4/42L 3/38L
2/34L 1/30L
Before using
Parts name........................................ 1
Cautions............................................
2
Installation and adjustment.................
4
How to usedrainpipe.......................... 5
Waterinlet installation........................ 6
Operation
Preparation before operation..............7
Load Laundries.................................
8
Useof detergent.................................9
Program operation............................ 10
control panel instructions................
10
operation steps............................. 12
Maintenance.................................... 13
Trouble shooting .................................
14
Other functions.................................
16
Specification.................................... 17
Contents

16
Other functions
1
Parts name
Before using
Symbol definition
Warning symbols
Pay special attention to the warning symbols. There may be
serous risks to personal body safety or damages to the washing
machine if not follow.
Please stop doing the contents with this symbol, otherwise
it will damage the appliance or injure your personal body.
Forbidden symbols
1. Give an alarm
E1
E3
E2
F1
E4
E0
Display Explanation Settlement
The top lid is opened
when preset is started Close the top lid and clear upthe alarm
After draining 5 minutes,
it still does not reach to
water level
Open top lid, according to before
troubleshooting and settlement to
settle it ,then close the top lidand
clear up the alarm.
The top lid is open when
spinning
Spin does not balance
Open the top lid ,make the laundries
place equally, then close it andclear
up the alarm
After inlet 20 minutes still
not reach to setting water
level
Open top lid, according to before
troubleshooting and settlement to settle
it. Then close the tip lidand clear up the
alarm
Water level sensor is
wrong
Cut the power supply and call the
technicians
vibration testing system will supervise the running. Once vibration is beyond certain
3. Power supply is cut offautomatically
violent vibration. This machine has imbalance adjustment function, and the
During spinning, if the laundries are not placed equally in the tub, it would cause
2. Imbalance adjustment
level, the adjustment system will start automatically to adjust the imbalance.
1) Press thepower supply buttonand does not start the programin 10 minutes,
the power supplywill be cutoff automatically.
2) Afterthe washing isfinished, buzzer will remind, the powersupply
can be cutoff automatically.
Close the top lid and clear upthe
alarm
Toplid
Topframe
Detergent box
Lint filter
Control panel
Inner tub
Pulsator
Body
Base
Power cord
Fixing foot(3pcs)
Back cover
Adjustable foot
Lint filterB
Foot wheel
Hot water inlet valve
Cold water inlet valve
Drainpipe
Accessories
The end connecting to
the appliance
Connector for
water inlet hose
and tap
The end connecting to
water inlet hose connector
Bottom cover
(1pc) Water inlet hose (2pc)
Outfall stopper
(1pcs)

15
Settlement
2
Cautions Before using
Don t install the washing machine in bathroom or damp
places,. Do not wash the machine with water, do not put
wet clothes on the control panel film.
Do not use water hotter than 50 C.
If the machine is situated on a carpeted floor, please adjust
the feet in order to allow air to circulate freely.
Do not wash raincoat, bike cover, feather dress and such
waterproof laundries, which will make the washing machine
abnormal vibrations during spinning.
Do not share the same socket with other electric appliances.
Do not use the damaged plug or loose socket.
Before using
Please insert the plug into the power socket with rated voltage
120V A/C.
Always unplug the appliance and turn off the water when
the power is cut, moving or cleaning the washing machine,
or it is not in use. Do not insert or pull off the plug with wet hand.
Do not make the electric cable bended, stretched, twisted, strapped or changed, pressed or nipped. If the electric cable or plug is
damaged or the socket becomes loose, they must be repaired or changed by our appointed repair stations or the professionals of
our post-sale service department to avoid danger. The pin of the plug must remain clean. Please clean it carefully with dry cloth if
it is dirty.
Ventilation holes
at the bottom
Soft item
Insert the plug tightly
Check the socket or change to another socket
Press power switch
Check power supply
Install the inlet hose again
Tighten the connector of the machine
Restart when water supply is resumed
Open the tap
Clean the filter according to before clean inlet gate
The machine is adjusting automatically
Close the toplid
Close the top lid
Normal
Normal
Notes If there is still a fault after the above checks, please pull out the plug and
contact the seller right away. It is dangerous to repair this product by yourself.
Settlement
The height of the drainpipe should be less than 1.2m
Straighten or clean the drainpipe

14
Troubleshooting
3
Dismantle Fit on
Any objects such as coins, safety pins, nails,
screws, stones or any other hard, sharp material
can cause extensive damage and must not be
placed into to the machine.
Before washing, please ensure the tap is open
and the inlet hose is installed properly.
It is suggested to use low foam washing powder.
Do not put hands into the working machine.
It is dangerous even if the speed is very slow.
Take special care of the children, and forbid
them to climb on the washing machine.
It is dangerous to alter the specifications or
attempt to modify this product in any way.
Do not overload the appliance or put any hot
goods(such as the kettle with hot water)on the
washing machine.
Garments which have been in contact with
volatile petroleum products should not be
machine washed.
Keep the appliance away from direct
sunlight and heat sources like the heater.
Toprevent the lint from blocking cascade outlet
during washing, pleasekeep the lintfilter in good
condition, install itto proper positionand clean it
in time.
Benzene
Petroleum
Thinner
Cautions Before using
This appliance is not intended for use by persons(including children)
with reduced physical,sensory or mental capabilities,or lack of
experience and knowledge,unless they have been given supervision
or instruction concerning use of the appliance by a person
responsible for their safety.
Children should be supervised to ensure that they do not play with
the appliance.
It does not drain
It does not inlet
Spin stops and begins to inlet
during spin program
Press the program button to
select SPIN, but It does not spin
The spin is intermittent when spin
starts
First time to use, some water flows
from the drainpipe
No water supply
Tap is not open
Inlet hose gets blocked
Laundries is too much or too little or the
Machine is not place stably
Before contacting the technicians, please make the following checks:
Control panel has no any display
Plug is not inserted tightly
No electricity in the socket
Power switch is not turned on
Power supply is cut off
Inlet hose leaks
Inlet hose connector(connecting with the tap)is not fixed tightly
Inlet hose and washing machine connector is loose
The remaining water when the factory make test
Do not closethe top lidwhen drain is finished
Open up thetop lid whenstart drain
Balance the laundries to reach to the best spin effect
Phenomena Possible reason
Water outlet of drainpipe is higher than 1.2m
drainpipe is bended or get blocked

Maintenance Operation
13
Groove
1.Once you haveusing the machine, you are advisedto turn offthe water taps.(if necessary, pullout
the inlet hose)
2. Do notkeep water in tub for along time. When washing is finished , drain itright away.
3.Once you havefinished using the machine, you areadvised to unplug it.
4. Put theelectric cable and the drain hosein order.
5. Wipe thewater on the surface and intub with soft cloth and keep the top lidopening for a while. It
helps to preventmould and stagnant smells forming inside the appliance.
The machine stopsautomatically ,and music
buzzer will remindyou to take out the laundries
or start again.
Once you havefinished using the machine,
you are advisedto unplug it and turn offthe
water taps toavoid unexpected leak or fire.
After the end of the programme Clean the exteriorcabinet of the appliance with
soft cloth. Donot use cleanser, volatile chemical
materials to cleanthe machine, which will
damage plastic partsand the surface.
External cleaning
It is necessaryto use lint filter during
washing.
After washing, pleaseclean the lint
filter in time.
Clean the lintfilter according to the
following steps:
1. Pull outthe lint filter.
2. Turnthe filter net outside and
wash it.
3. Recover thefilter net and
remount it.
Clean the lint filter Clean inlet gate
It is possiblethat the inlet filter net canbe blocked
by the dust,please clean it according to thefollow
steps:
1. Close thetap and turn on the powerswitch.
2. Start thewashing machine for 5 seconds(make
the water inthe inlet hoseflows to the tub),and
cut off thepowersupply.
3. Pull offthe inlet hose,remove and clean the inlet
valve and theinlet net, andinstall again.
Maintenance methods
4
Loosen Fasten
Adjustable
nut
Adjustable
foot
High Low
Please install and adjust the machine according to the requirements of the manual.
It is very important to your safety and correct operation.
Unpacking
Unpack the carton and take out the bottom panel.
Open the top lid of washing machine and take out all of the accessories.
Remove all wrappers, including the polystyrene base.
You are advised to keep all the packaging for reuse in case the machine is to be
transported again.
Positioning
The distance between the washing machine and the wall should be more than 50mm, and the
maximum allowed angle of the shank base of the machine is 1 .The slanting or rough ground may
cause operating stopped or unstable, please adjust it with the following methods:
Make ithorizontal
Use a tied thread with plumb to check
if it is horizontal.
Adjustthe adjustable foot
1 Lift up the adjustable foot gently, loose the adjustable nut
and twist the adjustable foot.
2 Fasten the nut after adjustment.
Installation and adjustment Before using
If the water in the inner tub has possibility to freeze,please do like below:
1. In winter, if remaining water freeze can cause the washing machine trouble,
please take off the water inlet hose and drain out the water in the hose and inner
tub.
2. If the water freeze, please don't operate the washing machine. Put 40 hot water
in the tub, the hot water should submerge the pulsator, after a few minutes, rotate
the pulsator by hand gently, then you can operate the washing machine.
1
Installing the bottom cover
Let the back of washing machine incline forward make
the side of bottom cover with sticker description back to
washing machine insert to the bottom of washing machine
along the direction of arrow.
Remove two fixing clamp by scissors insert to the
accordingly holes red lines indicating gently pull
fixing clamp should not be pulled out make the
bottom cover fixed on the base.
Fixing clamp
Scissors
Bottom cover
The base

12
Operation steps Operation
5
How to use drainpipe Before using
1. Press power switch, put through power, the machine is in state of beginning
4. Select appropriate water level according to your laundries quantity.
5.Press WATER TYPE to select HOT COLD or WARM water for
wash, during the rinse process, it will inlet cold water.
6. Close the top lid, press START/PAUSE, the washing machine is working.
7. When the washing is finished, buzzer alarm, power supply cut off automatically.
0
1
2
3
4
5
Times of pressing
the process button
Selected procedure
program
Applicable
procedure
Contents(the lighted indicator
indicate the programsabout
to run)
Wash, rinse, spin
Soak, wash,
rinse ,spin
Wash
when use detergent
repeatedly Wash light is on
Wash, rinse
Rinse ,spin
Spin
Standard program
For dirty laundries
No need tospin for
laundries creased easily
Wash by hand and
need to rinseand rinse
Wash by hand and
only need tospin
Wash rinse and spin
lights are on
Soak, wash, rinseand
spin lights areon
Wash and rinse lights
are on
Rinse and spinlights
are on
Spin light ison
Remarks: press PROCESSbutton continually, the above mode will be
cycled in turn.
2. Press program button to select proper program
3. Press process button to begin process selection
1). if there is no water in inner tub,washing machine is in state of "FUZZY",the state details
as per each model's button explanation. Now press "START/PAUSE" button (press
"PROGRAM" and select "STRONG",the washing machine is in state of "FUZZY"), the
washing machine will start fuzzy sensor and to sensor the weight of laundries and set
water level automatically.
2). If there is water in inner tub, washing machine is not in state of "FUZZY",the state details
as per each model's button explanation.Now press "PROGRAM" and"PROCESS" to select
proper program and process.
Operation steps
1.the drainpipe must be hanged during use, the
height is not more than 1.2m to avoid leakage or stop,
if drain a long time, the machine will stop running.
2. You can adjust the situation of the elbow bend
pipe to change the height of the drainpipe.
3. Do not extrude the drainpipe to ensue drain smoothly.
Drainpipe
Elbow
Less than 1.2m

11
Operation
6
Water inlet installation Before using
After select program, process and water level, press
this button to start.
Press this button to pause during working, press again
will rework .
Can select one program from NORMAL,STRONG,SOFT, SPEEDY,ULTRASPIN
At the beginning of start, the process is NORMAL.
To control the washing machine is in
working state or waiting state.
When washing, the digital timer shows
At the beginning of start, if with FUZZY logic,
When trouble encountered, the digital time
shows trouble code.
the rest time of washing, unit is MIN.
The digital timer shows -- .
Press this button to select HOT,COLD,WARM.
At the beginning of start, the process is COLD.
At the beginning of start, if with FUZZY logic and do not select water level, the digital timer
shows - - at this time, before press START/PAUSE, If select NORMAL or STRONG,
with fuzzy logic. When select SOFT, no fuzzy logic, the water level is 7 When
select speedy, no fuzzy logic, water level is 2 . If no WASH process, no fuzzy logic.
During wash (including rinse), if need to add water, press WATER LEVEL button to add
water, un-press will stop adding. Or PAUSE the washing machine and press WATER
LEVEL to select higher water level, then press START/PAUSE button, The washing
machine Will add the water to setting level automatically and continue working. If your
resetting water level is lower than present water level, the lowe r water Level will valid in
next water inlet.
At the beginning of start, press WATER LEVEL to select water level, at this time, no fuzzy
logic function, you can select appropriate water level. According to your laundries quantity.
1-2 is low water level, 3-6 is middle water level,7-10 is high water level.
Automatically add water: during SOAK, WASH and RINSE process, if the washing
machine check the water level is lower than setting water level, The washing machine
will pause and add water to setting water level automatically.
Tap selection
Suitable tap Not suitable tap
1. Swing the inlet hose gently to confirm if it is
fastened.
2. After installation,open the tap and check if
it leaks.
3. Do not bend the inlet hose with overstrain.
4. Before each usage,check the connection
between inlet hose connector and the tap.
Make sure they are firmly fitted to prevent
dropping from improper installation position.
Inlet valve connector
Inlet hose nut
Water absorption cushion
Connect the inlet hose with the washing machine
Check the connection between inlet
hose connector and the tap
1. Do not take off the water absorption cushion. Please
check if the cushion is dropped or damaged before
each usage. If it is, contact the seller immediately.
2. Put the inlet hose nut on the inlet valve connector.
3. Fasten the inlet hose nut and swing it gently to make
sure if it is suitable.
ºÏÊʵÄË®ÁúÍ·
The front end should be longer than 10mm. The tap exit end
face should be flat and smooth, if not file it to avoid leakage
Cautions:When install thewashing machine, please use the newhose assy alongwith the washing
machine, old hoseassy can not reuse.

Press this button to select one cycle from wash-rinse-spin
spin soak-wash-rinse -spin wash wash-risne
rinse-spin .
At the beginning of start, the process setting is wash-rinse-spin .
10
Control panel instruction
7
Mode and meaning of the indicator light
on: indicate the selected mode
flashing: indicate the program is running
At the beginning of start state
Put through the power, press POWER button, the machine is in the state of beginning of start:
1. If no water in the inner tub, the washing machine is in state of FUZZY, the process is wash,
rinse, spin . The program is NORMAL ,digital timer shows -- , at this time, if press
START/PAUSE button(or press program to select STRONG),the washing machine can
automatically set the water level according to the laundries quantity.
2. If there is water in the inner tub, and the machine is in state of non FUZZY, the water level setting
is 7 . Process is wash,rinse, spin program is NORMAL .
Preparation before operation Operation
Preparation before washing
1. Connect the inlet hose and open the tap.
2. This appliance must be earthed. Confirm
the socket is earthed reliably and insert the
power plug. The earth terminal should not
link to gas pipeline, tap pipeline etc.
3. Hang up the drainpipe.
Before washing the laundries, please pay attention to the followings:
Make sure if there is
special requirements
for the laundries
Before washing, empty
all pockets of small
objects which may
have been left inside
(coins,keys,screws etc.)
As these could damage
the drain pump.
Knot the long band,
fasten the buttons
and close the zippers.
Do not overload the
machine. Load the
laundry loosely
alternating large
items with small ones.
Sort the laundry
according to the type
of fabric, color-fastness
and how dirty it is. Put
thin laundries, woolens
and such prone to wear
and tear laundries into
washing bag.
A. Make sure the laundries are washable.
B. It is essential to wash new colored items separately when washing for the first time. White items
should not be washed with colored items.
C. Please immerge the non-absorbable laundries by hand.
D. Some stains such as fruit, wine, grass, rust etc. are difficult to remove and should be treated
before washing with specific products, which can be found in most household shops. In some
cases it may help to soak the stain before washing with a special pre-soak product or biological
detergent.
E. Overturn the nap fabric and long floss laundries before putting them into the machine.
F. Do not put the laundries polluted by chemicals into the machine directly.
G.Very small item(handkerchiefs, ribbons, socks etc) should be washed in a washing bag or a pillow case.
Warning: the temperature of the water should less than 50

9
8
Operation
It is suggested to use low foam washing powder
For the quantity of the concentrated washing powder, please refer to its manual
Remarks avoid splashing of water and waste of washing powder, water level should not be too
high if laundries are too small.
Withdraw the dispenser box before adding detergent
Pour concentrated synthetic washing powder into
the box directly as shown in the left illustration.
The dosage of the washing powder, please refer to
below.
It is suggested to use low sud washing powder.
How to use the washing powder
Detergent box
How to use bleach
Fill water tothe selected level,
dilute the bleachin the container,
and pour itslowly into thewashing
tub.
Do not usebleach for coloredor
figured laundries asthey are prone
to lose colors.
Do not putbleach to laundries
directly.
Refer to themanual for theusage
and quantity ofthe bleach.
Please dissolve powderbleach
before use.
Use of detergent
Dissolve in the machine directly not suitable for
preset program
1. Low water level.
2. Add the washing powder, and run for 30 seconds
to dissolve it completely.
3. Put laundries in, select suitable water level.
The instant dissolving of the washing powder
1. Prepare warm water of 30 in a container.
2. Pour the powder while stirring to fully dissolve it.
The washing powder is more prone to pollute the
laundries than the detergent, therefore, please use
it with proper quantity.
Washing powder with poor quality or not used for a
long period may get blocked, please clean the
detergent box in time.
Load laundries Operation
The capacity of washing and spinning of the machine refer
to the largest weight of the standard laundries under dry
condition .Washingquantity shall be lower than the rated
capacity.The maximum capacity of this machine is 7.0kg.
Different thickness, size and type of the laundries will
influence the actual washing capacity. It is suitable that
the laundries can be turned round normally during washing.
Do not select high water level when laundries are less than
1.0kg to avoid water splashing.
Use of detergent