Hoskin & Muir Cardinal Skyline Series User manual

73-11A
503F
19MM
502G1
512A
501E1
505S
50H
Connector Bracket
Door Stops
Support Bar
Panel Glass Bracket
Wall Mount Bracket
Rollers
Center Guide
Recessed Finger Pull
Fixed Panel (3/8” Clear Glass)
Rolling Panel (3/8”Clear Glass)
Glass Block
2
2
1
2
2
3
1
1
1
1
2
STEP 1
Using the centerline of tub/shower base as a starting point, come down
3” from overall height of shower and drill holes on both walls for bar
attachment. If you’re drilling into wood, use a 3/16” drill bit. If using the
anchors, use a 1/4” drill bit. If your tub has outages, and you’re
measuring up from the tub or shower base, make sure to allow for your
outages so the bar will be completely level when installed.
Place anchor in hole (if needed) and silicone in hole. The connector
bracket (Part number 73-11A) consists of two parts, a tubular sleeve and
a wall-mount puck. Using your allen key remove your wall mount puck
located inside the tubular sleeve. Attach wall mount pucks using 1-1/2”
screws provided. See figure 1. Tighten screw down inside puck. Make
sure the slot in the puck is vertical to allow for some leveling adjustment.
STEP 2
Slide door stops (Part number 503F) a few inches down onto each end
of the bar and use a small amount of tape to hold it in place so it won’t
slide off during installation of the rod. See figure 2.
Page 69
Cardinal Shower Enclosures are manufactured by Hoskin & Muir, Inc.
Updated Dec 1, 2012
INSTALLATION INSTRUCTIONS
PARTS LIST
ITEM PART DESCRIPTION QTY
FIXED PANEL SLIDING PANEL (GOES ON SHOWER HEAD SIDE)
FIGURE 1
FIGURE 2

STEP 5
Install the two panel glass bracket (Part number 502G1) on bar securely using allen key. Set panel glass on glass blocks and
loosely attach with brackets to bar. See figure 5. This is to accurately mark the holes for drilling.
STEP 3
Slide tubular parts of connector brackets (Part number 73-11A) onto each
end of bar. See figure 3.
STEP 4
Place bar in-line with mounted wall pucks and slide connector brackets
over puck. Ensure that the flat spot of the connector bracket is facing
towards glass side. Tighten set screws on top and bottom of connector
bracket to secure the bar. See figure 4.
STEP 6
Ensure panel glass is level and plumb before marking holes for the two
wall mount brackets (Part number 512A). See figure 6 for marking holes
for wall mount bracket, caps have been removed in this figure.
Note: part has adjustment if required.
After marking holes remove puck from the inside of the wall mount bracket.
Updated Dec 1, 2012
Cardinal Shower Enclosures are manufactured by Hoskin & Muir, Inc.
Page 70
INSTALLATION INSTRUCTIONS
FIGURE 3
FIGURE 4
FIGURE 5
FIGURE 6

Wall mount bracket (Part number 512A) shown disassembled in figure 7.
The wall mount bracket is adjustable. If your drill can be used without
touching the glass, you do not need to remove the panel to install the wall
mount brackets.
STEP 9
Make any necessary adjustments to the wall mount bracket and tighten set
screw with allen key. See figure 10.
STEP 8
Thread wall mount bracket onto puck. See figure 9.
STEP 7
Drill a hole in the center of your mark. If you’re drilling into wood, use a
3/16” drill bit. If using the anchors, use a 1/4” drill bit. Place silicone and
anchor into hole and install puck. See figure 8.
Page 71
Cardinal Shower Enclosures are manufactured by Hoskin & Muir, Inc.
Updated Dec 1, 2012
INSTALLATION INSTRUCTIONS
FIGURE 7
FIGURE 8
FIGURE 9
FIGURE 10

STEP 10
Reinstall glass panel on glass blocks and secure wall mount brackets (Part
number 512A). See figures 11, 12 and 13.
STEP 11
Attach glass panel to the panel glass brackets (Part number 502G1) and
use provided spanner wrench to secure. See figure 14.
Updated Dec 1, 2012
Cardinal Shower Enclosures are manufactured by Hoskin & Muir, Inc.
Page 72
INSTALLATION INSTRUCTIONS
FIGURE 11
FIGURE 12 FIGURE 13
FIGURE 14

STEP 12
Install two part number 501E1 (qty. 3) rollers into top 2 holes of door panel.
Using provided CRL SOW wrench and spanner wrench to tighten roller to
door glass. See Figure 15, 16 and 17.
STEP 13
Carefully set door glass on bar for purposes of marking for center guide
only. Hold glass plumb and mark both holes and install center guide (Part
number 505S). See figure 18. It is important to put silicone in screw holes
and properly silicone guide itself to avoid leaking.
NOTE: Guide has two settings. Use tighter setting for 3/8” glass.
STEP 14
Hang door on rail and install bottom roller loosely as in previous step for
top rollers. See figure 19.
NOTE: If having issues getting bottom roller installed see next step
for cam system adjustment to allow extra clearance.
Page 73
Cardinal Shower Enclosures are manufactured by Hoskin & Muir, Inc.
Updated Dec 1, 2012
INSTALLATION INSTRUCTIONS
FIGURE 15
FIGURE 16 FIGURE 17
FIGURE 18
FIGURE 19

STEP 15
Notice there is a cam system installed in the
rollers that will allow adjustment for small
outages. Using level adjust top rollers with
provided spanner wrench and then snug bottom
roller to rail to ensure the door glass will not
come off track. See figure 20.
STEP 17
Install recessed finger pull (Part number 50H) using gaskets provided. See
figure 22.
Note: The recessed pull
consists of five pieces. When
mounting, try to center the
threaded middle section
between the two end rings.
STEP 18 (Optional)
Polycarbonate is provided as an option for the edge of the door to help
seal against wall.
STEP 19 (Optional)
Silicone the inside and outside of the stationary panel, both wall and curb.
STEP 16
IMPORTANT: GLASS STOPS MUST BE ADJUSTED PROPERLY
TO KEEP GLASS FROM STRIKING WALL AND/OR WALL
CONNECTORS AND BREAKING.
Adjust glass stops (Part number 503F) for required stopping distance
for glass door. See figure 21.
Updated Dec 1, 2012
Cardinal Shower Enclosures are manufactured by Hoskin & Muir, Inc.
Page 74
INSTALLATION INSTRUCTIONS
FIGURE 21
FIGURE 20
FIGURE 22