HSW 2209 User manual
Bevertalstraße 20
D-42499 Hückeswagen
Phone: +49 2192 9166 0
Fax: +49 2192 9166 66
Installation Instructions
Cable fuse box HSW 2209
Intended use
The cable fuse box HSW 2209 is intended to be used in suitable
lighting poles.
The cable fuse box HSW 2209 is designed for the connection of
max. 3 underground cables.
Any other use of this product requires the consultation with the
manufacturer.
Safety instructions
When working on electrical systems, the valid regulations such as
VDE 0100 must be observed. Installation may only be carried out by
qualified personnel or instructed persons in a de-energized state.
Service
In the event of malfunctions or complaints regarding the product,
please contact your sales representative or the manufacturer.
Technical data
Nominal voltage /
-current
400 V / 16 A
Degree of protection
IP54
Protection class
II
Measurements (L x W x H)
290 x 84 x 72 mm
Pole internal diameter
from Ø 89 mm
Door size
80 x 300 mm
Entry field for wire
connection
up to 110 mm
Input connectors
max. 3 cables
5 x 6 - 16 mm²
Mounting in lighting poles
▪Remove housing cover
▪Remove bridge clamp
▪Insert the cable fuse box into open lighting pole and fasten it to
the mounting rail
Bridge clamp strain relief
can be snapped into the lower part
of the housing for easier installation.
For disassembly, the side lugs must
be operated with a slot screwdriver
Adjust input seal
▪Important! With one input cable, always use the existing opening
of the input seal!
▪Break out the inlet seal at the engraved points according to the
number and diameter of the input cables
Connecting the input cable
▪Strip the input cable and remove
the filling material
▪Insert the input cable so that the
outer sheath extends into the
connection compartment
▪Snap on bridge clamp and screw
tight
▪Bending, shortening and stripping
cable conductors to suit
▪Mount or remove the PE/N - N
connection, if present, as
required
▪Insert the cable cores into the U-
profiles according to the terminal
assignment and fasten with the
self-locking sliding clamps (torque
max. 2 Nm)
▪Snap the contact hazard
protection cover on
Connecting the output cable
▪Cut off the nipple of the outlet seal to be used
▪Slide outlet seal over output cable
▪Strip output cable
▪Insert the outlet seal with output cable into the slot of the cable
fuse box
▪Pull the output cable back a little so that the outgoing seal is in full
contact with the cable
▪Shortening and stripping cable conductors to suit
▪Connect the cable cores to the output terminals of the insert
(torque max. 0,8 Nm) or to special components according to the
cable assignment
Assembly
▪Fit housing cover, snap the housing
cover and screw it tight
Special components
▪When special components are used, the respective regulations of
the devices used must be observed
Changing fuse inserts
▪Remove housing cover
▪Remove screw caps and change fuse insert
▪Attention! Do not remove the contact hazard protection cover! It
prevents from the accidental contact with live parts!
Print errors and technical changes excepted (Status: August 2019)
Bevertalstraße 20
D-42499 Hückeswagen
Phone: +49 2192 9166 0
Fax: +49 2192 9166 66
Installation Instructions
Cable fuse box HSW 2209
Intended use
The cable fuse box HSW 2209 is intended to be used in suitable
lighting poles.
The cable fuse box HSW 2209 is designed for the connection of
max. 3 underground cables.
Any other use of this product requires the consultation with the
manufacturer.
Safety instructions
When working on electrical systems, the valid regulations such as
VDE 0100 must be observed. Installation may only be carried out by
qualified personnel or instructed persons in a de-energized state.
Service
In the event of malfunctions or complaints regarding the product,
please contact your sales representative or the manufacturer.
Technical data
Nominal voltage /
-current
400 V / 16 A
Degree of protection
IP54
Protection class
II
Measurements (L x W x H)
290 x 84 x 72 mm
Pole internal diameter
from Ø 89 mm
Door size
80 x 300 mm
Entry field for wire
connection
up to 110 mm
Input connectors
max. 3 cables
5 x 6 - 16 mm²
Mounting in lighting poles
▪Remove housing cover
▪Remove bridge clamp
▪Insert the cable fuse box into open lighting pole and fasten it to
the mounting rail
Bridge clamp strain relief
can be snapped into the lower part
of the housing for easier installation.
For disassembly, the side lugs must
be operated with a slot screwdriver
Adjust input seal
▪Important! With one input cable, always use the existing opening
of the input seal!
▪Break out the inlet seal at the engraved points according to the
number and diameter of the input cables
Connecting the input cable
▪Strip the input cable and remove
the filling material
▪Insert the input cable so that the
outer sheath extends into the
connection compartment
▪Snap on bridge clamp and screw
tight
▪Bending, shortening and stripping
cable conductors to suit
▪Mount or remove the PE/N - N
connection, if present, as
required
▪Insert the cable cores into the U-
profiles according to the terminal
assignment and fasten with the
self-locking sliding clamps (torque
max. 2 Nm)
▪Snap the contact hazard
protection cover on
Connecting the output cable
▪Strip the output cable, shortening and stripping cores
▪Insert the output cable through the cable gland
▪Screw the pressure nut together until the seal set between nut and
cable forms a small bead
▪Connect the cable cores to the output terminals of the insert
(torque max. 0,8 Nm) or to special components according to the
cable assignment
Assembly
▪Fit housing cover, snap the housing
cover and screw it tight
Special components
▪When special components are used, the respective regulations of
the devices used must be observed
Changing fuse inserts
▪Remove housing cover
▪Remove screw caps and change fuse insert
▪Attention! Do not remove the contact hazard protection cover! It
prevents from the accidental contact with live parts!
Print errors and technical changes excepted (Status: August 2019)
