Ice RS26L Programming manual

Operator & Parts Manual
Rider Auto Scrubber
RS26L
RS28L
RS32L
INTELLIGENT CLEANING EQUIPMENT
8300050
REV.03 (03-2017)
www.icecompanies.com
www.icerental.com

2ICE RS26L / RS28L / RS32L
OPERATOR MANUAL
HOW TO ORDER PARTS
Only use ICE Company supplied or equivalent parts. Parts and supplies may be ordered
online,by phone, by fax or by mail.
1. Identify the machine model.
2. Identify the machine serial number from the data label.
3. Ensure the proper serial number is used from the parts list.
4. Identify the part number and quantity.
Do not order by page or reference numbers.
5. Provide your name, company name, customer ID number,billing and shipping address,
phone number and purchase order number.
Please ll out at time of installation for future reference.
Model No.
Serial No.
Machine Options
Sales Rep.
Sales Rep. Phone No.
Customer ID Number
Installation Date
READ OPERATOR MANUAL CAREFULLY!
ICE Company Limited
XiangShi Road LiaoBu DongGuan GuangDong China
Tel: 0769 - 81869000
Fax:0769 - 81863000
Specifications and parts are subject to change without notice.
IMPORTANT: To ensure full warranty protection, please ll out & return
your warranty card.
PROTECT THE ENVIRONMENT
Please dispose of packaging materials,old machine components
such as batteries, hazardous uids, including antifreeze and oil, in an
environmentally safe way according to local waste disposal regulations.
Always remember to recycle.

3ICE RS26L / RS28L / RS32L
OPERATOR MANUAL
SAFETY PRECAUTIONS......................................................................................................4
MACHINE COMPONENTS................................................................................................5-6
MACHINE SETUP & INSTALLATION....................................................................................7
MACHINE OPERATION........................................................................................................8
WHILE OPERATING MACHINE............................................................................................9
TANK DRAINING.................................................................................................................10
BATTERY CHARGING........................................................................................................10
PREVENTATIVE MAINTENANCE.......................................................................................11
FAULT CODE AND ELIMINATE..........................................................................................12
TECHNICAL SPECIFICATION............................................................................................13
PARTS LIST..................................................................................................................14-39
WEAR AND TEAR PARTS...............................................................................................40
WIRING DIAGRAM.............................................................................................................41
TABLE OF CONTENTS

4ICE RS26L / RS28L / RS32L
OPERATOR MANUAL
SAFETY PRECAUTIONS
This machine is intended for commercial use. It
is designed exclusively to scrub hard oors in an
indoor environment and is not constructed for any
other use. Only use recommended accessories.
All operators shall read, understand and
exercise the following safety precautions:
1. Do not operate machine:
-Unless trained and authorized.
-Unless you have read and understand the
operators manual.
-In ammable or exploxive areas.
-With brake disabled.
-If not in proper operating condition.
2. Before starting machine:
-Make sure all safety devices are in place
and operate properly.
-Check brakes and steering for proper
operation.
3. When using machine:
-Go slow on inclines and slippery surfaces.
-Follow all safety guidelines.
-Be very careful when using the machine in
reverse.
-Reduce speed when turning.
-Report and x any damage to machine prior
to operating it.
-Never allow children to play on or
around.
4. Before leaving or servicing machine:
-Stop on level surface.
-Turn off machine.
5. When servicing machine:
-Read operators manual thoroughly prior to
operating or servicing this machine.
-Use manufacturer supplied or approved
replacement parts.
-Secure machine with wheel blocks prior to
jacking the machine up.
-Use approved jack or hoist to safely elevate
the machine.
-Disconnect batteries prior to working on
machine.
-Avoid moving parts. Do not wear loose tting
clothing while servicing machine.
WARNING: Explosion or re can result
from hydrogen gas. Keep sparks and open
ames away! Keep battery compartment
open when charging.
WARNING: Flammable materials can
cause an explosion or re. Do not use
ammable materials in tanks.
WARNING: Flammable materials or
reactive metals can cause explosion or re.
Do not pick up.

5ICE RS26L / RS28L / RS32L
OPERATOR MANUAL
MACHINE COMPONENTS
1. Solution tank
2. Hose ll port & Cap
3. Squeegee assembly
4. Wheels, 10 inch
5. Scrub head assembly
6. Side squeegee assembly
7. Watching window, on-
board battery charger
8. Brake pedal
9. Propel pedal
10. Front drive wheel
11. Operator seat
12. Steering wheel
13. LED light, work
14. Adjusting handle, seat
15. Off-board battery
charger receptacle
16. Detergent level watching
window
17. Warning light
18. Recovery tank cover
19. Recovery tank
20. Cup holder
21. Cap
22. Detergent bottle
23. Battery box

6ICE RS26L / RS28L / RS32L
OPERATOR MANUAL
MACHINE COMPONENTS
24. i-synergyTM, ID card scanning
area
25. Emergency stop switch
26. Directional switch
27. Warning light switch
28. Vacuum motor switch & indicator
29. Detergent dosage adjusting
buttons & indicator
30. Batteries meter
31. LED display screen
32. Fault indicator
33. Fault code
34. Fault message
35. Hour meter
36. Solution ow adjusting buttons &
indicator
37. Horn button
38. 1-Step switch & Indicator
39. Brush pressure adjusting button
& indicator
40. Drain hose, recovery tank
41. Drain hose, solution tank
42. Vacuum hose

7ICE RS26L / RS28L / RS32L
OPERATOR MANUAL
i-synergyTM collects operational data from
cleaning machines and transmit the information
to ICE’s server. The ICE server generates daily
reports and send them to designated end users
by email. From these reports, end users will
have information about machines’ usage and
even specic timings.
Besides, i-synergyTM also collects data on
lithium-ion battery, vacuum motor, brush
deck motor, transaxle, and other electrical
components at least once every minute when
the machine is in use and even during battery
charging.
i-synergyTM will send notications instantly
to the ICE server in case of any malfunction.
ICE maintenance personnel will receive a
SMS within minutes from the ICE server for
immediate servicing.
UNCRATING MACHINE
Be sure and check packing carton for any damage.
Immediately report any damage to carrier. Check
the contents of package to ensure that the
following items are included:
• Machine
• Lithium-ion Batteries
• Squeegee assembly
• 2-Pad drivers
1. Uncrate the wooden box, place the top board
on the edge of pallet, lie in the front of the
machine, as below shown.
WARNING: Do not operate machine unless
you have read & understood this manual.
2. Install batteries.(see INSTALLING BATTERIES)
3. Place the ID card on the scanning area (machine
components, #24) to turn on the machine,
make sure the Squeegee assembly (machine
components, #3) and the Scrub head assembly
(machine components, #5) is off the oor.
4. Sit in the Operator seat (machine components,
#11), hold the Steering wheel (machine
components, #12), press the Propel pedal
(machine components, #9) and driving slowly
the machine down from the slope.
INSTALLING BATTERIES
The machine uses the Lithium-ion batteries,
the batteries are already in the machine upon
delivery; However you will need to connect the
Lithium ion batteries to the machine.
WARNING: Fire or Explosion Hazard.
Keep sparks and open ames away! Keep
battery compartment open when charging.
1. Turn off the machine.
2. Open and prop up the Operator seat, plug the
batteries connector to the machine adaptor,
connect machine i-synergyTM COM port to the
batteries.
MACHINE SET UP
INSTALLING BRUSHES OR PADS
1. Turn off the 1-Step switch (machine
components, #38) and raise the Scrub head
assembly off the oor, then stop machine on the
level surface, ensure the machine is turned off.
2. If using the pad driver, rst attach the
appropriate pad to the pad driver surface.
3. Align the pad driver or brush under the motor
hub and push it upward to engage.
4. To remove the pad driver or brush, raise the
scrub head and remove the Side squeegee
assembly (machine components, #6), push the
edge of brush downward.
MACHINE SET UP & INSTALLATION
i-synergyTM INTRODUCTION

8ICE RS26L / RS28L / RS32L
OPERATOR MANUAL
MOUNTING THE SQUEEGEE ASSEMBLY
1. Turn off the 1-Step switch and raise the
Squeegee assembly off the oor.
2. Mount the squeegee assembly to the squeegee
pivot bracket. make sure the knobs are
completely seated into the slots before securing
knobs.
3. Connect the Vacuum hose (machine
components, #42) to the squeegee assembly.
Loop the hose by using the hose clip provided.
4. Check the squeegee blades for proper
adjustment.
FILLING THE SOLUTION TANK
The machine is equipped with a Hose ll-port
(machine components, #2) at the side of the
machine, and a bucket ll-port located under the
recovery tank.
NOTE: Before accessing the bucket ll-port
make sure that the recovery tank is empty.
When lling the solution tank with a bucket,
make sure that the bucket is clean. Do not use
the same bucket for lling and draining the
machine.
WARNING: Do not put any ammable
materials into solution tank. this can cause an
explosion or a re.
FILLING THE DETERGENT BOTTLE
The machine is equipped with a 6 liters Detergent
bottle (machine components, #22). Open the Cap
(machine components, #21) you can ll detergent,
and watch the liquid level on the Detergemt level
watching window (machine components, #16).
The ratio of water and detergent is 0~5%, you can
adjust this ratio via pressing the Detergent dosage
adjusting buttons (machine components, #29).
NOTE: Only use recommended cleaning
chemicals. Contact your janitorial supply
distributor for recommendations on
properchemicals.
WARNING: Do not operate machine
unless you have read and understand this
manual.
PRE-OPERATION CHECKS
1. Check the tank cover seals for damage.
2. Drain the recovery tank, check the vacuum fan
inlet lter, clean them if necessary.
3. Check the vacuum hose for debris or blockage.
4. Check the squeegees for damage, wear and for
deection adjustment.
5. Check whether Pad/Bruch is installed properly .
6. Check the brakes and steering for proper
operation.
OPERATION THE MACHINE
1. Sit in the Operator seat, adjusting the seat
to comfortable place by pushing the Seat
adjustment handle (machine components, #14).
NOTE: The machine will not travel unless the
operator is sitting in the operator seat.
2. Turn on the machine.
Check the LED display screen (machine
components, #31) , if there are fault codes
(machine components, #33) and the Fault
indicator (machine components, #32) is blink,
please Do Not operation the machine unless the
faults have been eliminated (please see FAULT
CODES AND ELIMINATE section).
3. Select the preferred settings by pressing the
Brush pressure adjusting buttons (machine
components, #39) , Solution ow adjusting
buttons (machine components, #36) and
Detergent dosage adjusting buttons.
NOTE: Use the minimal pressure and ow
as possible.
4. Turn on the 1-Step switch, the Scrub head
assembly and the Squeegee assembly will
lower down automatically, all the presetting
functions will turn on.
5. The machine can scrub in both forward and
backward, place the Directional switch (machine
components, #26) in the forward direction is to
move forward, backward is to move backward.
The horn will sound and the squeegee will
raise automatically (the vacuum motor will turn
off after a short delay) when drive machine
backwards. This is to prevents damaging the
squeegee.
NOTE: Go slow when drive machine
backwards.
MACHINE OPERATION

9ICE RS26L / RS28L / RS32L
OPERATOR MANUAL
6. Press the Propel pedal, the machine start
scrubbing, the speed can be adjusted by
controlling the force of foot stepping, light is
slow, heavy is fast.
NOTE: Go slow on inclines and slippery
surfaces.
7. To stop scrubbing, turn off the 1-Step switch,
the scrub head will raise automatically, the
squeegee will also raise after a short delay (the
vacuum indicator ashing), please keep moving
until the dirty water is picked up, and then
release the propel pedal and stop scrubbing.
8. Turn off the machine.
BRAKE DEVICE
The machine is drived by the Front drive wheel
(machine components, #10), that is equipped
with a brake device. When you release the Propel
pedal, the machine will stop travel, the park brake
will engage after a short delay.
The machine is equipped with a Brake pedal
(machine components, #8), that can be used to
control the machine if quicker stopping is needed
or if operating on an incline.
EMERGENCY STOP BUTTON
The machine is equipped with an Emergency stop
button (machine components, #25), please push
it if an emergency, that will shut off all power of
machine and brake immediately.
To restart the machine, please reset the
Emergency stop button, and turn off the machine
and then restart.
NOTE: Please hold the steering wheel when
emergency stop.
WARNING: Fire Or Explosion Hazard. Do
Not Pick Up Flammable Materials Or Reactive
Metals.
1. Go slow on inclines and slippery surfaces, go
slow when turn and reverse. Do not operate the
machine on inclines that exceed 7% (4°).
2. Drive machine in a straight path as possible,
avoid turning the Steering wheel too sharply
when machine is in motion. avoid sudden turns
except emergencies.
3. Do not keep the machine in the same position
with pad / brush spinning, keep the machine
moving to prevent damage to oor nish.
4. If the squeegee assembly leaves streaks on the
oor, raise the squeegee off the oor and wipe
the blades down with a damp cloth. Pre-sweep
the area to prevent leaving streaks on the oor.
5. To obtain the optimum cleaning performance,
you can adjust the brush pressure, solution
ow and detergent dosage as your required. If
poor picking up water performance is observed,
please stop scrubbing and check the squeegee
blade, adjust or replace if necessary.
6. If the dirty water path exceed the width of
squeegee, please adjust the side squeegee
assembly.
7. Pour a recommended defoamer into the
recovery tank if excessive foam appears.
WARNING: The foam do not activate
water level switch, excessive foam may result
in vacuum motor damage.
8. Press the Horn button (machine components,
#37) to alert if necessary.
9. The machine is equipped with a Warning light
(machine components, #17), you can select turn
ON or OFF by the Warning light switch (machine
components, #27).
10. If there is a fault code F10 (Batt low) on the
LED display screen, the machine will stop
scrubbing and alarm, please drive the machine
to charging.
11. If there is a fault code F08 (Rec Tank Full)
on the LED display screen, the vacuum motor
will stop working and alarm, please drive the
machine to drain water.
If there is a fault code F09 (Soln Tank Empty)
on the LED display screen, the Detergent
system will stop working and alarm, please ll
the solution tank.
12. If there are other fault codes on the LED
display screen, please turn off the machine,
eliminate the fault (please see FAULT CODES
AND ELIMINATE section), then restart machine.
13. For heavily soiled areas, please use DOUBLE
SCRUBBING mode.
The rst time: Turn on the 1-Step switch, then
press the Vacuum motor switch (machine
components, #28), its indicator will turn off and
the squeegee will raise automatically, then start
to scrubbing this areas without picking up water.
The second time: turn on the Vacuum
motor switch, the squeegee will lower down
automatically, and then start to scrubbing and
picking up water.
14. If you only want to pick up water needn't
scrubbing, Turn on the Vacuum motor switch
(squeegee will lower down) and turn off the
1-Step switch (if it is ON), the scrub head will
raise and then start to working.
WHILE OPERATING MACHINE

10 ICE RS26L / RS28L / RS32L
OPERATOR MANUAL
BATTERY CHARGINGTANK DRAINING
DRAINING THE RECOVERY TANK
Any time scrubbing is completed, or when relling
solution tank, the recovery tank should be drained
and cleaned.
WARNING: If the recovery tank is not
drained when the solution tank has been
relled, foam or water may enter the oat shut-
off screen and cause damage to the vacuum
motor.
1. While holding the Recovery tank drain hose
(machine components, #40) upward, remove
the cap and lower hose to drain.
2. Open the Recovery tank cover (machine
components, #18) and rinse out the tank. Use
a rag to remove any excess dirt.
3. Remove and clean the vacuum fan inlet lter
located in the recovery tank. Clean the lter with
a damp cloth or low pressure water hose if dirty.
Allow the vacuum fan lter to dry completely
before reinstalling it in the machine.
DRAINING THE SOLUTION TANK
Any time scrubbing operation is completed, the
solution tank should be drained and cleaned.
1. While holding the Solution tank drain hose
(machine components, #41) upward, remove
the cap and lower hose to drain.
2. Rinse the solution tank with clean water after
every use. This will help prevent chemical
buildup and clogging of the solution lines.
WARNING: Fire Or Explosion Hazard.
Keep Sparks and Open Flame Away. Keep
Battery Compartment Propped Open When
Charging.
Use only ICE supplied or apprved batteries
charger, use unapproved charger may cause
damage to the batteries and machine.
Batteries charger specications:
• Applicable to charging Lithium-ion batteries
• Automatic shut off circuit
• Output current of 30 Amps
• Output voltage of 24 volts
1. Transport the machine to a well ventilated area.
2. Turn the machine off.
3. Prop up the Operator seat by the support stand
for ventilation.
4. Connect the charger's AC power supply cord to
a properly grounded receptable.
5. The charger will automatically begin to charge,
you can watching the charging status on the
window (machine components, #7), once the
charging cycle begins, the indicator lights will
progress from red, yellow to green. when the
green indicator light comes on, the charging
cycle is done. Unplug the charger cord.
NOTE: The machine will can not operate
when charging.

11 ICE RS26L / RS28L / RS32L
OPERATOR MANUAL
WARNING: Before performing any
maintenance on the machine, be sure that
the power is turned off, or the batteries are
disconnected!
WARING: Repairs are to be completed
by Authorized service centers only. Any repairs
completed by unauthorized persons will avoid
the warrenty.
DAILY MAINTENANCE
1. Remove pad driver/ brush and clean with
approved cleaner.
2. Drain recovery and solution tanks completely
and rinse out with clean water. Visually check
the recovery tank for debris and clean out as
necessary.
3. Raise the squeegee assembly off oor and wipe
it down with a damp towel. Be sure to store the
squeegee in the up position.
4. Remove the vacuum fan inlet lter and rinse it
out with clean water.
5. Clean machine with an approved cleaner and a
damp towel.
6. Recharge the batteries.
7. Check the condition of the squeegee blade
wiping edge, rotate blade if worn.
MONTHLY MAINTENANCE
1. Clean the battery tops to prevent corrosion.
2. Check for loose battery cable connections.
3. Inspect and clean the recovery tank cover seal.
Replce it if damaged.
4. Lubricate all grease points and pivot points with
silicon spray and approved grease.
5. Check the machine for loose nuts and bolts.
6. Check the machine for leaks.
MACHINE STORAGE
1. Always store the machine indoors.
2. Always store the machine in a dry area.
3. Always store the machine in its upright position.
4. Always store the machine with the pad driver/
brush raised off the oor.
5. Always store the machine with the squeegee
assembly raised off the oor.
6. If storing in an area which may reach freezing
temperatures, be sure to drain all uids from the
machine prior to storage. Any damage caused
by freezing temperatures will not be covered by
the warranty.
7. Drain the recovery tank.
8. Drain the solution tank of all uid.
PREVENTATIVE MAINTENANCE
FAULT CODE & SOLUTION
The machine is equipped with a LED display
screen (see Machine components, item # 31), the
LED screen will display the operating hours (see
Machine components, item # 35) and the battery
level status (see Machine components, item # 30).
When the machine detects a fault, there will be a
Fault code (see Machine components, item #33)
& Fault message (see Machine components, item
#34) display on the LED screen, and the Fault
indicator (see Machine components, item #32) will
ash continuously, accompany an audible alarm
Occasionally.
Once fault occuring, please DO NOT continue
operate the machine unless the fault are eliminated.
Turn off the machine, then to solve the fault, the
fault code & message will be eliminated when
machine restart.
If the fault is occurred frequently, or the fault can't
be eliminated, please contact ICE service center.
Please refer to the below table to determine the
fault cause and the solution.

12 ICE RS26L / RS28L / RS32L
OPERATOR MANUAL
FAULT CODE & SOLUTION
FAULT
CODE FAULT MESSAGE FAULT CAUSE SOLUTION
F01 Seat Empty Not sit in the seat Sit in the operator seat
F02 Squeegee Actt O.L.
RE-START! Squeegee lifting actuator is overload
Turn off the machine,after a moment,
RE-START machine.
F03 Bru Actt O.L.
RESTART! Scrub head lifting actuator is overload
F04 Vac Mtr O.L.
RE-START! Vacuum motor overload
F05 Left Bru Mtr O.L.
RE-START! Left brush motor is overload
F06 Right Bru Mtr O.L.
RE-START! Right brush motor is overload
F07 Propel Mtr O.L.
RE-START! Propel motor overload
F08 RecTank Full Recovery tank is full Drain the Recovery tank
F09 Soln Tank empty Solution tank is empty Fill the solution tank
F10 Batt Low
Charge Batt Battery is low Charge the battery
F11 Batt Empty
Charge Batt NOW Battery is empty Charge the battery NOW
F12 Brake Wiring Error Bad Brake wiring Check the brake wiring
F13 Release Foot pedal Stepping the propel pedal when
starting machine Release the propel pedal
F14 Replace Brake Assy Bad Brake assembly Replace the brake assembly
F16 Control Unit Overheat!
Wait Control Unit Overheat Turn off the machine,after a moment, RE-START machine
F17 Replace Control Unit Control Unit Fault Replace the control unit
F18 Replace Accel Pedal Sensor Bad Accelerator pedal sensor Replace accelerator pedal sensor
F19 Replace Brake pedal sensor Bad Accelerator pedal sensor Replace accelerator pedal sensor
F20 Check Left Brush motor Bad left brush motor Check left brush motor/ wiring
F21 Check Vac Mtr Bad Vacuum motor or wiring Check the vacuum motor / Wiring
F22 Check Soln Solenoid Solution solenoid wiring fault Check the wiring & Contactors
F23 Replace Soln solenoid Bad Solution solenoid Replace the solution solenoid
F24 Check Propel Motor Bad propel motor Check the propel motor / Wiring
F25 Check Right Brush motor Bad right brush motor Check right brush motor/ wiring
F40 Check Proximity Sw Proximity switch fault Check the Proximity switch
F42 Replace Control Unit Bad Control Unit Replace the control unit
F43 Turn Dead Sw Off
RE-START! Emergency stop button activated Release emergency stop button and restart machine
F44 Replace Control Unit
Bad Control Unit Contact service center, Replace the
Control Unit
F45 Return Control Unit
F46 Return Control Unit
F47 Return Control Unit
F48 Return Control Unit

13 ICE RS26L / RS28L / RS32L
OPERATOR MANUAL
TECHNICAL SPECIFICATIONS
MODEL RS26L RS28L RS32L
LENGTH 61.6 in / 1,565 mm
WIDTH (MACHINE WITH
SCRUB HEAD) 32 in / 815 mm 33.7 in / 855 mm 37.4 in / 950 mm
HEIGHT 56.7 in / 1,440 mm
WEIGHT 618 lbs / 280 Kg 640 lbs / 290 Kg
WEIGHT WITH BATTERIES 880 lbs / 400 Kg 900 lbs / 410 Kg
RECOVERY TANK CAPACITY 29 Gal / 110 L
SOLUTION TANK CAPACITY 29 Gal / 110 L
SQUEEGEE WIDTH 33.8 in / 860 mm 40 in / 1,030 mm
CLEANING PATH WIDTH 26 in / 650 mm 28 in / 710 mm 32 in / 810 mm
PRODUCTIVITY RATE PER
HOUR (IN THEORY)
46, 300 ft2
4,300 m2
49, 500 ft2
4,600 m2
55, 600 ft2
5,200 m2
TRAVEL SPEED
(TRANSPORT)
4 Mile / h
6.5 Km / h
MINIMUM AISLE TURN 71 in / 1,800 mm 75 in / 1,900 mm
PAD/BRUSH PRESSURE
80 lbs / 35 Kg
120 lbs / 55 Kg
160 lbs / 75 Kg
SOLUTION FLOW 0 ~ 0.7 Gal / Min
0 ~ 2.7 L / Min
BATTERIES Lithium-ion batteries, 240AH
VOLTAGE 24V DC
DRIVE WHEEL 1.1 hp / 0.8 KW
BRUSH MOTOR (2) 0.6 hp / 0.45 KW, 210 RPM
VACUUM MOTOR 0.6 hp / 0.45KW
VACUUM WATER LIFT (MAX) 70 in. H2O / 1780 mm. H2O
RUN TIME PER CHARGE 3~3.5 Hours
DECIBEL RATING AT
OPERATOR'S EAR, INDOORS 68 dB(A)
GRADE LEVEL, MAX Scrubbing: 4°/7% Transporting (empty):10°/17.5%

14 ICE RS26L / RS28L / RS32L
PARTS LIST
MAIN FRAME GROUP

15 ICE RS26L / RS28L / RS32L
PARTS LIST
MAIN FRAME GROUP
DIA
NO.
PART
NUMBER DESCRIPTION NO REQ'D
1 8310102 MAIN FRAME, WELDED 1
2 8310133 RUBBER GROMMET 5
3
8310930A PERISTALTIC PUMP, KIT 1
8310931 TUBING, PUMP 1
4 1421409 FLAT WASHER, M4×∮9×0.8 2
5 1422411 LOCK WASHER M4 2
6 1221412 SCREW, PAN HEAD, M4×12 2
7
8310119 10" WHEEL, PU TIRE 2
1612605 BALL BEARING,6205-2RS 4
8 1436025 RETAINING RING, 25MM 2
9 8310150 WHEEL CAP 2
10 6210131 NYLON, CLAMP 5
11 1421510 FLAT WASHER, M5×∮10×1.0 5
12 1221512 SCREW, PAN HEAD, M5×12 5
13 8310120 BRACKET, STAND 2
14 1421824 FLAT WASHER, M8×∮24×2.0 3
15 1422821 LOCK WASHER M8 3
16 1021825 BOLT, HEX, M8×25 3
17 1021840 BOLT, HEX, M8×40 1
18 1121807 HEX NUT, M8 1
19 1123810 LOCK NUT M8 1
20 8310158 BRACKET,PROXIMITY SENSOR 1
21 8134709A PROXIMITY SENSOR, KIT 1
22 1421612 FLAT WASHER, M6×∮12×1.6 2
23 1422616 LOCK WASHER M6 2
24 1021616 BOLT, HEX, M6×16 2
25 8210118 STATIC STRAP 1
26 8310708A HORN, 24VDC, KIT 1
27 1421307 PLAT WASHER, M3×∮7×0.5 4
28 1211316 SCREW, PAN HEAD, M3×16 2

16 ICE RS26L / RS28L / RS32L
PARTS LIST
STEERING & DRIVE WHEEL GROUP

17 ICE RS26L / RS28L / RS32L
PARTS LIST
STEERING & DRIVE WHEEL GROUP
DIA
NO.
PART
NUMBER DESCRIPTION NO REQ'D
1 1113014 LOCK NUT, M14 1
2 1421428 FLAT WASHER, M14×∮28×2.0 1
3
8310602 STEERING WHEEL 1
8310699A CUSHION WITH ICE LOGO 1
4 8310608 BELLOWS, SHAFT, STEERING 1
5 1021825 BOLT, HEX HEAD, M8×25 8
6 1422821 LOCK WASHER, M8 6
7 1421816 FLAT WASHER, M18×∮16×1.6 4
8 8310609 BEARING, FLANGE 2
9 8310605 SHAFT, STEERING WHEEL 1
10 1654025 KEY, 4.75×4.75×25.4 2
11 8310604 U-JOINT 1
12 1534508 SET SCREW, M5 ×8 4
13 1123507 LOCK NUT, M5 3
14 1421510 FLAT WASHER, M5×∮10×1.0 3
15 6210131 CLAMP, NYLON 3
16 8310645 BRACKET, FLANGE BEARING 1
17 1021060 BOLT, HEX HEAD, M10×60 4
18 1422026 LOCK WASHER, M10 4
19 1421030 FLAT WASHER, M10×∮30×2.5 4
20 8310601 SUPPORT BRACKET, STEERING 1
21 1021820 BOLT, HEX HEAD, M8×20 4
22 1421824 FLAT WASHER, M14×∮24×2.0 8
23 8310640 ACCELERATOR/ BRAKE PEDAL 1
24 8310431 HALL SENSOR WITH CABLE 1
25 8310603 STEER-CONTROL ASSY. 1
26 8310650 DRIVE WHEEL, 24VDC 800W 1
27 8310611 PU TIRE, DRIVER WHEEL 1
28 8310612 ARMATURE BRUSH 4
29 8310613 BRUSHES CONNECTION BOX 2
30 8310618A ELECTRICALLY RELEASED BRAKE 1

18 ICE RS26L / RS28L / RS32L
PARTS LIST
SOLUTION TANK GROUP

19 ICE RS26L / RS28L / RS32L
PARTS LIST
SOLUTION TANK GROUP
DIA
NO.
PART
NUMBER DESCRIPTION NO REQ'D
1 8310101 SOLUTION TANK 1
2 1221512 SCREW, PAN HEAD, M5×12 2
3 1421510 FLAT WASHER, M5×∮10×1.0 2
4 8113009 CLAMP, NYLON 2
5 1021820 BOLT, HEX HEAD, M8×20 12
6 1421824 FLAT WASHER, M8×∮24×2.0 13
7 8310139 PLATE 2
8 8310151A NON-SLIP MAT 2
9 8310132 FOOTREST PLATE 1
10 1222508 SCREW, M5×8 4
11 1512820 SCREW, HEX SOCKET, M8×20 2
12 1421816 FLAT WASHER, M8×∮16×1.6 2
13 8310140 JUNCTION PLATE 2
14 1422821 LOCK WASHER, M8 8
15 8310130 BRACKET, SOLUTION TANK MNTG 3
16 8310124 ELBOW, G1/2 1
17 8310142 NUT, M36 1
18 8310141 SEALING 2
19 8310238A SENSOR, SOLUTION LEVEL, KIT 1
20 8310125 CAP, SOLUTION TANK 1
21 1021825 BOLT, HEX HEAD, M8×25 1
22 8310225 SLEEVE, ∮8.1×∮12.7×7.8 1
23 8310224 ARM, RECOVERY TANK SUPPORT 1
24 1962050 CLAMP, 2 INCH 1
25 8011030 HOSE ASSEMBLY 1
26 8310123 ADAPTER, STRAINER ASSY 1
27 8310122 STRAINER ASSY 1

20 ICE RS26L / RS28L / RS32L
PARTS LIST
RECOVERY TANK GROUP