INNOVAPLAS BILTMOR 5001 User manual

Sand
50 lbs
BILTMOR 5001 WITH CLASSIC LADDER 6003
(not included)
Sand
Required tools and supplies (not included)
A
Contents of the ladder box SKU # 6003 Contents of the Biltmor box SKU # 5001
WARNING
105-005
115-005
105-012
x4
x2
x2 x4
x2
A weather resistant padlock is
recommended.
115-005
105-005 105-012
x6
x6
x6
Do not dive or jump from step or ladder.
Use BATTERY operated tools to avoid electric shocks.
Install step on flat surface, following the manufacturers
instructions.
Remove step from pool during freezing climate season.
Manufacturer cannot be held responsible for injuries caused
by abusive use of product.
Ask your city about specific regulations that apply to your
above-ground pool and ladder.
REV. 28/10/10
PN: 110-097
1) Assemble the two main modules with the six
screws, nuts and washers provided.
2) Snap the door between the top and bottom
modules within the slots provided.
115-014 (3/4 in.)
x6 x6 x6
x16
Maximum functional
width is 1/4 inch.
PG. 1
SCREW BAG 140-020
x2
105-012
105-005
x2 x2
115-014 (3/4 in.)
x18
Security Strap
x2
CABLE LOCK
***PADLOCK REQUIRED
115-018 (2 1/2 in.)
x2
SCREW BAG 140-058
x2
x2
115-006 (1 in.)
x2
x2
370 Lajeunesse St,
St-Jérome (Québec),
Canada J7Y4E5

G
BC
D
F
REV. 28/10/10
PN : 110-097
Sand
50 lbs
MANUFACTURER
WARRANTY
1 Year on the Classic
ladder and Biltmor.
1 year on the hardware.
E
1) Snap the four post ends
into the step making sure
that the cylindrical part is
vertical and that the ends
are placed and fitted
properly in their respective
housings.
2) Snap the 2 feet to the
bottom of the step.
1) Insert the four posts into the post
ends and secure them in place with
the screws provided.
2) Insert the platform over the 2 rear
posts.
3) Insert the small and large handrails
as illustrated. Secure the large
handrails with the screws provided.
Leave the small handrails floating.
1) Install the four
post covers.
2) Insert a bag of sand
onto surface provided
at the rear of the step.
1) Slowly submerge
the Step in the pool.
Make sure you do not
damage the liner in
the process.
x16
115-014 (3/4 in.)
Security strap
x2
2) Once the step is
in the pool secure
the platform to the
top seat (see
illustration) using
the two straps
provided.
115-018 (2 1/2 in.)
x2
PG. 2
OPTIONAL:
Once the pool step has been
completely assembled and
secured to the pool, attach the 2
screws supplied through the
platform to the top seat of your
pool to provided a more rigid
assembly.
A
1) Trace a line on each post at 39 inches from the ground for 48'' &
52'' Pools. If you have a 54'' pool trace a line at 40.5'' from the ground.
2) Slide the pivot blocks onto the posts and line up with the traced
marks. Secure with the screws provided.
3) Slide the 2 posts through the platform and handrails.
4) Secure the handrails and platform to
the posts with the screws provided.
5) Secure the ladder base to the post
with the screws provided.
x18
115-014 (3/4 IN.)
48'' & 52''
54''
align
x2
105-012
105-005
x2 x2
125-035
2) Secure the
ladder to the
pivot blocks
using the
bolts, washers
and nuts
provided.
H
SWING THE LADDER UP
AND LOCK IN PLACE
WHEN THE POOL IS NOT
IN USE TO PREVENT
DROWNING AND
UNAUTHORIZED ENTRY.
WARNING
CABLE LOCK
***PADLOCK REQUIRED
x1
370 Lajeunesse St,
St-Jérome (Québec),
Canada J7Y4E5