SportsPlay 511-114 User manual

511-114 SIT-UP STATION Page 1 of 1
Rev 4/7/03
Sportsplay Equipment, Inc., 5642 Natural Bridge, St. Louis, MO 63120 [phone]
* IMPORTANT *
PLEASE RETAIN THIS INSTRUCTION SHEET IN YOUR FILES. IT CONTAINS IMPORTANT REPLACEMENT
PARTS INFORMATION. ALL EQUIPMENT SHOULD BE INSTALLED IN ACCORDANCE WITH THESE
INSTRUCTIONS.
IT IS IMPORTANT TO USE AND MAINTAIN ALL PUBLIC PLAYGROUND EQUIPMENT PROPERLY. PLAYGROUND
EQUIPMENT WHICH IS IMPROPERLY MAINTAINED CAN CAUSE SERIOUS INJURY. PERIODICAL
INSPECTIONS, MAINTENANCE, REPAIR AND/OR REPLACEMENT OF DAMAGED PARTS IS NECESSARY FOR
SAFE OPERATION OF EQUIPMENT AND SAFETY OF USERS. RESILIENT SURFACING SHOULD BE USED
UNDER ALL PLAYGROUND EQUIPMENT. APPROPRIATE PUBLICATIONS, AVAILABLE AT NO CHARGE, FROM
THE CONSUMER PRODUCT SAFETY COMMISSION, INCLUDE “A HANDBOOK FOR PUBLIC PLAYGROUND
SAFETY.” YOU CAN RECEIVE YOUR FREE COPY BY CALLING 1-301-504-7908.
PACKING LIST HARDWARE BAG
1 CTN - 1 Hardware Bag 12 - 605-506 Clips
1 BDL - 3 603-906 6’ Alum Board 4 - 116-512 5/16” x 3” Hex Hd Bolt
1 BDL - 3 603-505 Angles 12 - 126-504 5/16” x 1” Carriage Bolt
1 BDL - 4 503-216 Legs 16 - 316-501 5/16” Flat Washer
1 PIPE - 1 513-615 Toe Bar 16 - 216-501 5/16” Hex Nut
1 - 805-532 Warning Label
1 - 805-534 SportsPlay Label
1 - Maintenance Checklist
1 CTN 3 BDL 1 PIPE 5 TOTAL PCS WT 80# CLASS 70

511-114 SIT-UP STATION Page 2 of 2
Rev 4/7/03
Sportsplay Equipment, Inc., 5642 Natural Bridge, St. Louis, MO 63120 [phone]
GENERAL USE/FALL ZONE & FOOTING RECOMMENDATIONS
STATIONARY & PORTABLE EQUIPMENT – USE/FALL ZONES SHOULD EXTEND A MINIMUM OF 6 FEET IN ALL
DIRECTIONS FROM THE PERIMETER OF THE EQUIPMENT GROUND SPACE. THIS AREA SHOULD BE COVERED
WITH THE REQUIRED AMOUNT OF RESILIENT SAFETY SURFACING MATERIAL. FOR SOME EQUIPMENT –
USE/FALL ZONES CAN OVERLAP. SEE CONSUMER PRODUCT SAFETY COMMISSION GUIDELINES.
DIAMETER & DEPTH OF FOOTING ILLUSTRATED ARE SATISFACTORY IN MOST APPLICATIONS FOR PIPE
SIZES UP TO 2 3/8” DIAMETER. VARYING SOIL & CLIMATIC CONDITIONS MAY REQUIRE DEEPER &
HEAVIER FOOTINGS IN SOME AREAS. CHECK LOCAL BUILDING CODES.
* If resilient surfacing is to be less than 12”, then additional pipe should be put in
concrete to maintain proper finish grade for equipment.

511-114 SIT-UP STATION Page 3 of 3
Rev 4/7/03
Sportsplay Equipment, Inc., 5642 Natural Bridge, St. Louis, MO 63120 [phone]
GENERAL ASSEMBLY INSTRUCTIONS:
Check all the parts and hardware with the packing list to be sure you have received
everything needed to assemble this product. CONTACT YOUR LOCAL DISTRIBUTOR WITH
NOTIFICATION OF ANY MISSING OR DAMAGED PARTS. Contact must be made within ten days of
receipt of your order.
Only hand-tighten nuts & bolts on initial assembly. Final tightening should be done
EVENLY after final assembly when unit has been plumbed & leveled.
After assembly is complete, ANY ENDS OF BOLTS PROTRUDING BEYOND NUTS SHOULD BE CUT OFF
AND/OR PEENED OVER TO REMOVE ANY SHARP EDGES. Go over entire unit to file smooth any
sharp edges or projections that may have been caused by rough handling in shipping or
installation. T-Clamps are designed for both one and two bolt connections. In many
situations only one bolt is required. See specific assembly instructions.
On products with platforms install 1 – 2 degrees off level to facilitate water drainage.
GENERAL MAINTENANCE INSTRUCTIONS:
Check MONTHLY for loose bolts, damaged or broken parts. Tighten and/or replace
immediately.
SPECIFIC ASSEMBLY INSTRUCTIONS:
STEP #1: Mark & dig footing holes per SKETCH on PAGE #2.
STEP #2 &
#3:
STEP #4: Stand up & brace in footing holes. Length of pipe below intended level of
resilient surfacing should be 24”. Two long braces holding 2 legs each are
recommended.
STEP #5: Plumb & level entire unit. Pour Concrete. Tighten all nuts & bolts so that
lock washers are flat. Wait 48 hours before removing braces, installing
Resilient Surfacing & using equipment.
STEP #6: Attach Warning Label and Manufacturer’s Identification Label to a clean
surface. The Labels should be attached in a location where they are clearly
visible and legible and away from normal hand and foot placement areas. The
Labels must be replaced if they become illegible, destroyed or removed.
Contact your distributor for replacement Labels.