Inspire FPC1 Installation and operating instructions

PAGE 1
FPC1
FULL POWER CAGE

PAGE 2
FPC1 RACK- SH-G8901
ASSEMBLY & OWNER’S MANUAL
Toll-Free Customer Service
Number
1-877-738-1729
Mon. - Fri. 8 a.m. - 5 p.m.
PST
www.inspirefitness.com
BEFORE YOU BEGIN
Thank you for selecting the INSPIRE FPC1 RACK. For your safety and benefit, read this
manual carefully before using the machine. As a manufacturer, we are committed to
providing you complete customer satisfaction. If you have any questions, or find there are
missing or damaged parts, please call our TOLL-FREE customer service number. Our
Customer Service Agents will provide immediate assistance to you.
Table of Contents
BEFORE YOU BEGIN 1
IMPORTANT SAFETY NOTICE 3
PARTS LIST 4
EXPLODED VIEW 6
ASSEMBLY INSTRUCTIONS 7
REGULATORY INFORMATION/ SAFETY NOTICE 13
WARRANTY / DISCLAIMER 17

PAGE 3
IMPORTANT SAFETY NOTICE
Precautions
This exercise machine is built for optimum safety. However, certain precautions apply whenever you
operate a piece of exercise equipment. Be sure to read the entire manual before you assemble or
operate your machine. Please note the following safety precautions:
1. Always keep children and pets away from the machine. DO NOT leave children
unattended in the same room with the machine. The linkages on this machine can cause
serious injury or death if used improperly.
2. Never place your hands or feet in the path of the linkages because injury may occur to
you or damage may occur to the equipment. Never allow children to come near or
approach the moving linkages while in use.
3. If the user experiences dizziness, nausea, chest pain, or any other abnormal symptoms,
STOP the workout at once. CONSULT A PHYSICIAN IMMEDIATELY.
4. Position the machine on an open and level surface.
5. DO NOT use the machine outdoors or near water.
6. Keep hands away from all moving parts.
7. Always wear appropriate workout clothing when exercising. DO NOT wear robes or
other clothing that could become caught in the machine. Running or aerobic shoes are
also required when using the machine.
8. Use the machine only for its intended use as described in this manual. DO NOT use
attachments not recommended by the manufacturer.
9. Do not place any sharp objects around the machine.
10. Disabled persons should not use the machine without a qualified person or physician in
attendance.
11. Before using the machine to exercise, perform stretching exercises to properly warm up.
12. Never operate if the machine is not functioning properly.
Care and Maintenance
1. Keep moving parts clean.
2. Inspect and tighten all parts before using the machine.
3. The Frame can be cleaned using a damp cloth and mild non-abrasive detergent. DO NOT
use solvents.
WARNING:
BEFORE BEGINNING ANY EXERCISE PROGRAM, CONSULT YOUR PHYSICIAN. THIS IS
ESPECIALLY IMPORTANT FOR INDIVIDUALS OVER THE AGE OF 35 OR PERSONS WITH
PRE-EXISTING HEALTH PROBLEMS. READ ALL INSTRUCTIONS BEFORE USING ANY
FITNESS EQUIPMENT. Health In Motion, LLC. DOES NOT ASSUME ANY
RESPONSIBILITY FOR PERSONAL INJURY OR PROPERTY DAMAGE SUSTAINED BY OR
THROUGH THE USE OF THIS PRODUCT.

PAGE 4

PAGE 5
EXPLODED VIEW

PAGE 6
COMPONENTS LIST
7X 1
6X 1
18 X 1
9X 1
8X 1
10 X 1
11 X 1
16 X 4
23 X 2 17 X 10
14 X 1

PAGE 7
COMPONENTS LIST
13 X 4
4X 1
2X 2
40 X 2
12 X 2
15 X 4
5X 4
3X 1
1 X 2

PAGE 8
HARDWARE PACK

PAGE 9
STEP 1.
BOTTOM SUPPORT FRAME ASSEMBLY
Refer to the illustration above for location and orientation of components.
This step consists of a left side and a right side.
•Fasten with Bolt (28), Washer (36), and Locknut (35). Connect Bottom Foot Plate (15) to
Bottom Base Frame (1), Bottom Inner Plate (13), and the Bottom Cross Brace (14), place
these items towards the one end of the Bottom Base Frame.
•Repeat Step for the Opposite side.
•Fasten with Bolt (29), Washer (36), and Locknut (35). Connect Bottom Foot Plate (15) to
Bottom Base Frame (1), and Bottom Inner Plate (13), and the Bottom Cross Brace (14),
place these items towards the one end front of the Bottom Base Frame.
•Repeat Step for the Opposite side.
•Together, these Items form the Bottom support Assembly.

PAGE 10
STEP 2
Upright BeamS AND REAR CONNECTING FRAME INSTALLATION
Refer to the illustration above for location and orientation of components.
•Fasten with Bolt (28), at the bottom, Bolt (29) above, Washer (37), and Lock-Nut (35).
Connect Upright Beam (5) to the Bottom Support Frame Assembly. Left side and Right
side. (Refer to the illustration above for placement).
•Fasten with Bolt (29), Washer (36), and Lock-Nut (35). Connect the Rear Cross Bar(3) to
the Upright Beams (5) and fasten in place.

PAGE 11
STEP 3
Upright Beams FRONT INSTALLATION
Refer to the illustration above for location, and orientation of components.
•Fasten with Bolt (29) at the bottom, Washer (36), and Lock-Nut (35). Connect Upright
Beam (5) to the Bottom Support Frame Assembly. Left side and Right side.
•Repeat steps for the opposite side.

PAGE 12
STEP 4
UPPER CROSS BARS INSTALLATION
Refer to the illustration above for location, and orientation of components.
•Fasten with Bolt (29), Washer (37), Washer (36), and Lock-Nut (35).
•Connect the Upper Cross Bar (2), to the 2 the Upright Beams. Left side
and Right side.
•Repeat steps for the opposite side.
Fix washer 37 #to appear

PAGE 13
STEP 5.
Monkey Bar INSTALLATION.
Refer to the illustration above for location, and orientation of components.
•Fasten with Bolt (31), Washer (36), and Lock-Nut (35).
•Connect the Monkey Bar (4), to the Upper Cross Bars (2), and Deco Plate
(23). Left side and Right side.

PAGE 14
STEP 6
RESISTANCE BAND PEGS, , LANDMINE, AND BATTLE ROPE ATTACHMENT
INSTALLATION.
Refer to the illustration above for location, and orientation of components.
RESISTANCE BAND PEGS (4 Places): one at top, and one at bottom on each side.
•Fasten with Bolt (30), Washer (36), and Lock-Nut (35).
•Connect Resistance Band Pegs (16) to the bottom frame, and to the top of the frame. one on
each side, left and right.
LANDMINE:
•Fasten with Bolt (29), Washer (36), and Lock-Nut (35).
•Connect the Landmine bracket (18) to the bottom frame.
BATTLE-ROPE ATTACHMENT:
•Fasten with Bolt (29), Washer (36), and Lock-Nut (35).
•Connect the Battle-Rope attachment bracket (17) to the bottom frame.

PAGE 15
STEP 7
HOOKS, PARALLEL BARS, AND SAFETY TUBES ATTACHMENT.
Before beginning a workout, make sure all the safety tubes are in place.
Locate a desired height to place the safety bar (12) thru the hole of the beam and the safety
sleeve (40).
Proceed to install in place:
Parallel bars (10), (11)
J-Cups (6), (7).
Safety Catches (8), (9).
(Please see illustrations on the next page for attachment).

PAGE 16
Step 3
Step 2
Step 1
Step 3
Step 2
Step 1
Step 3
Step 2
Step 1
Parallel bars (10), (11)
J-Cups (6), (7).
Safety Catches (8), (9)

PAGE 17

PAGE 18
Labels Placement
FPC1
FULL POWER CAGE

PAGE 19