INUX3D PRO Streamer YP PK1 User manual

© INUX3D 2022 V1.1
Assembly Instructions
Biodegradable according
to DIN EN ISO 14855
MADE IN EU
8 586022 660566
TUV
TUV Hessen
EN ISO
9001
2015
ADDITIVE MANUFACTURING
®
BLK
PRO
Streamer YP
Cage for YoloBox Pro
BLK
PRO
Streamer YP
Cage for YoloBox Pro
ADDITIVE MANUFACTURING
®
8 586022 660566
Lower Strut Assembly
All of the fasteners required for assembling this component are found in Bag 2.
Bag 2 contains 4 x M4*8mm bolts, 4 x M4 Hex Nuts and 4 x M2.5*6mm bolts
ŸFlip the entire assembly on it's back so that the undersides are visible.
ŸThe lower strut assembly comprises of 4 parts, 2 Left and 2 Right. Each part is
marked L or R
ŸUsing the M2.5x6mm bolts you will now join both the Left and Right lower
struts together to form a longer strut. The M2.5 bolt will pass through the bolt
hole on the Left part and you will screw directly into the plastic of the Right
part.
ŸYou will perform this step twice, creating 2 lower struts.
M2.5x6
M2.5x6
M4x8
M4x8
M4x8
M4x8 Rubber Foot
Rubber Foot
Rubber Foot
Rubber Foot
Front Right Strut
Front Left Strut
ŸWe will tighten the Top Left and Right bolts as well as the lower strut bolts to
stiffen up the entire assembly.
ŸPosition one of the lower strut assemblies into the notches under each of the
Left and Right sides.
ŸInsert an M4*8mm bolt from below and place an M4 hex nut into the nut
shaped recesses and loosely tighten the protruding bolt.
ŸRepeat for the second lower strut assembly.
ŸAttach the 4 rubber feet in the positions indicated in the diagram above.
DO NOT OVER TIGHTEN.
Biodegradable according
to DIN EN ISO 14855
MADE IN EU
8 586022 660252
Compatible with the ATEM Mini Extreme
and ATEM Mini Extreme ISO
INUX3D
d e s i g n s t u d i o
TM
TUV
TUV Hessen
EN ISO
9001
2015
5
INUX Cloud s.r.o.
Galvaniho 12B
Bratislava 82104
Slovakia
Assembly Instructions
This product was produced with an additive manufacturing process. Minor surface imperfections do not affect the overall product functionality. Instagram: @aaronpk_tv | Twitter: @aaronpk
You can also get support and show off photos of your rigs in our friendly community at
forum.livevideotech.today
Thanks so much for your support! I hope this stand makes your productions even more
successful. I'd love to see a photo of your new rig! Post a photo on Instagram or Twitter and
tag it with #pk1stand
- Aaron
Parts of this product were produced with an additive manufacturing process. Minor surface imperfections do not affect the overall product functionality.
Biodegradable according
to DIN EN ISO 14855
MADE IN EU
8 586022 660566
TUV
TUV Hessen
EN ISO
9001
2015
ADDITIVE MANUFACTURING
®
BLK
PRO
Streamer YP
Cage for YoloBox Pro
BLK
PRO
Streamer YP
Cage for YoloBox Pro
ADDITIVE MANUFACTURING
®
8 586022 660566
Biodegradable according
to DIN EN ISO 14855
MADE IN EU
8 586022 660566
TUV
TUV Hessen
EN ISO
9001
2015
ADDITIVE MANUFACTURING
®
BLK
PRO
Streamer YP
Cage for YoloBox Pro
BLK
PRO
Streamer YP
Cage for YoloBox Pro
ADDITIVE MANUFACTURING
®
8 586022 660566

© INUX3D 2022 V1.1
PK1 PRO STREAMER YP
Assembly Instructions Page 2 of 5
Begin by placing the left side of
the YP Cage smooth side down
with the cold shoes facing you
The left side is indicated by the
‘L’ embedded in the part
You are looking at the left rear
of the YP cage
Place your YoloBox Pro into
the side of the cage so that the
screen is facing away from you
You must now choose the nal
orientation of your YoloBox Pro
so the HDMI cables point up
( to the right in this image ) or
down ( to the left in this image )
A
A
B
BInsert the 2 aluminium bars into
the corresponding spaces in the
YP cage
Important:
Slide 2x M5 sliding T-Nuts for
the handle here
Slide 2x M5 sliding T-Nuts for
the CheeseBar tripod mount
here
Example
* Please note that your kit comes with extra M4 and M5 nuts and
bolts so you can attach other accessories you may already have

© INUX3D 2022 V1.1
Place the right side of the
YP cage over the top of
the YoloBox Pro and the 2
aluminium bars
Drop in two of the supplied
M5x10mm bolts, into the holes
to afx the right side of the YP
cage onto the aluminium bars
These only need to be lightly
tightened. You will damage the
plastic sides if you tighten with
force
Place your hand underneath
the left side which is currently
at the bottom
Flip the entire YP cage over while
pressing the sides together so
the left side is now on top
Drop in 2 more M5x10mm
bolts into the holes and lightly
tighten
Position the YP cage as shown
and note the 2x M5 slide in nuts
you dropped in earlier
We will be attaching the top
handle to these two T-nuts
PK1 PRO STREAMER YP
Assembly Instructions Page 3 of 5

© INUX3D 2022 V1.1
Place the handle on top of
the YP cage and very loosely
tighten the 2x M5x10 bolts into
the T-nuts
Now that you have both bolts
attached, slide the handle left
or right to centre it
You may now tighten the bolts
A
This is simply a zoomed in
view of how a cable manager
assembly should look once
attached
PK1 PRO STREAMER YP
Assembly Instructions Page 4 of 5
2
3
1Attaching the cable managers
requires the use of an M4x8mm
bolt through the cable manager
and into an M4 drop in nut.
Note that the nut ts into the
slot of the aluminium bar
1. Place the bolt through the
cable manager hole and very
loosely into the drop in nut
2. Position the drop in nut so that
it ts into the slot of the bar
3. Tighten the bolt so the drop in
nut turns and locks into place
at the position you require

© INUX3D 2022 V1.1
Attaching the cheesebar is like
the handle and utilises the two
slide in nuts we inserted earlier
We will attach bolts to the two
T-nuts that are visible here
A
Using 2x M5x8mm bolts, we will
lightly attach the cheesebar to
the slide in T-nuts
Once both bolts are attached
to the nuts, slide the cheesebar
so that it is centred along the
aluminium bar
You may now tighten the bolts
In the event you place your
YoloBox Pro such that the HDMI
cables are pointing downwards,
position the cheesebar so it
only covers the aluminium bar
and not the YoloBox Pro.
The HDMI cables will now be
clear of the cheesebar
PK1 PRO STREAMER YP
Assembly Instructions Page 5 of 5
Congratulations on completing
the assembly of your PK1 Pro
Streamer YP
Table of contents
Popular Enclosure manuals by other brands

Tripp Lite
Tripp Lite SmartRack SRW26US Brochure & specs

Tripp Lite
Tripp Lite SmartRack SRW12USNEMA Brochure & specs

Black Box
Black Box NEMA 12 Specifications

Rocket Fish
Rocket Fish RF-PHD35 Guide de l'utilisateur

Multilink
Multilink Starfighter 4048D installation instructions

Green Brook
Green Brook PowerBreaker ProteKt quick start guide