Jaycar Electronics XC4697 User manual

- 1 -
XC4697 Manual
Introduction：
XC4697 is a USB 3.0 enabled dual-SATA hard drive
enclosure. It supports simultaneous use of two 2.5” or 3.5”
SATA hard disk for both data read and data write. It also
backward compatible with USB 2.0 and USB 1.1. The
maximum transfer speed of USB 3.0 can reach 5Gbps. The
actual transfer speed of XC4697 is 400M/s.It supports Offline
Clone, which is able to copy data and system files from Source
HDD to Target HDD completely via finger touch. XC4697
provides high storage capacity, high data transfer rate, and best
data protection.
Function Chart：
1、Power indicator 2、Bay ‘A’ indicator 3、Bay ‘B’indicator
4、Clone processing indicator 5、Clone button 6、Bay ‘B’
7、Bay ‘A’ 8、USB3.0 input 9、Power switch (ON/OFF)
10、DC input

- 2 -
Caution:
1. Once using E-SATAinterface, it can only recognize one HDD
in PC. If 2 HDDs are inserted in the dock, it can only recognize
Bay ‘A’HDD. If only insert one HDD in the dock, both Bay’A’and
Bay ’B’ can be recognized.
Function：
•Complies with Gen2i/Gen2m of Serial ATA II Electrical
Specification 2.6
•Supports SATA II Asynchronous Signal Recovery (Hot Plug)
feature
•Supports SATAto SATApass through
•Complies with USB 3.0 Specification, USB Mass Storage
Class, Bulk-Only Transport Specification
•Supports USB Super-Speed/High-Speed/Full-Speed Operation
•Supports USB HID operation
•Supports USB2.0/USB3.0/eSATApower saving mode
•Supports Dual LUN for USB2.0/USB3.0
•One Touch Backup
•Easy to Install and Set-up
•Supports clone function
•Design for Win2000, WinXP, WinVista, Win7, MAC 9.2 or
later version.

- 3 -
CLONE:
Please note the below conditions before clone:
-Bay ‘A’ = SOURCE HDD,
-Bay ’B’ = TARGET HDD
-TARGET HDD ‘s capacity MUST be larger than SOURCE
HDD, otherwise the CLONE cannot be completed. (Same
capacity is also not acceptable)
-Before CLONE function starts, make sure the information
in TARGET HDD is not important; once CLONE started, all
information from the SOURCE HDD will be covered into
TARGET HDD..
-Once the docking is connected to USB interface, the offline
Clone will be invalid. Clone can only process by using USB
Clone Function.
1, Offline clone
a、Insert source HDD to Bay ‘A’; target HDD to Bay ‘B’, and then
turn on the power

- 4 -
b、Once the Bays indicators are on, that means XC4697 is
ready for clone.
c、Press and hold the clone button for 3 seconds until the
indicator light is on, press the button once more for Clone
confirmation. Offline clone is starting to process.

- 5 -
d、Clone progress indicator flashes and shows the progress
(25%, 50%, 75%, 100%).
e、Once clone is finished, all progress indicators will light up.
f、Turn off power and take out the HDD carefully

- 6 -
2, USB Clone
Drive Installation
a、Please insert the CD drive and click “setup.exe”. Choose
your language and click “ Next”
b、Fill in the S/N # accordingly (you can find the S/N# on the
cover of CD drive)

- 7 -
c、Click “Install” for installation
d、Installation progress is showed

- 8 -
e、please click “Done” once installation is finished.
3, Clone from Source HDD to Target HDD
a、Please insert Source HDD and Target HDD well to the
docking, connect XC4697 to PC via USB cable. Turn on the
power, you can find the clone icon on the right bottom of window,
then double click the CLONE Icon to start the program.
CLONE Icon

- 9 -
b、Clone drive activated, please click “Start”
c、Press start to proceed with Clone.

- 10 -
d、Clone progress is showed
e、Click “OK” once clone is finished