jbc CT-SA User manual

Solder Pot Cartridge Stand
Ref. CT-SA
www.jbctools.com

222

333
Packing List
The following items should be included:
Handle & Cartridge are not included
Ref. CT-SA
Solder Pot Cartridge stand
Solder Pot Cartridge stand .......................................................................................................................... 1 unit
Ref. CT-SA
Spatula 17 mm .......................................... 1 unit
Ref. 0017193
Tray ................................................................. 1 unit
Ref. 0016749
Lifters (x 2) ................................................... 1 unit
Ref. 0014899
Allen key Ø 2 mm .................................... 1 unit
Ref. 0916030
Spatula 39 mm .......................................... 1 unit
Ref. 0017194
Manual ........................................................... 1 unit
Ref. 0015011
www.jbctools.com
www.jbc tools .co m

444
Features
Operation
Knob
to fix on the bench
to fix on the bench
Residue Tray
Protective Screen
The CT-SA Solder Pot Cartridge Stand holds the handle T245 or T470 with the Solder Pot
Cartridge to avoid it tipping over accidentally. Find the cartridges availables in www.jbctools.com
As a safety precaution, before placing the handle, make sure the station is off and the tin is cold.
1. Unlock the knob and open the holder. 2. Place the handle with the cartridge. Be
careful to position it correctly.
3. Once in place, lock the knob and connect
the handle to the stand or the converter
(Ref. CHB-A).
- Do not melt “Cored Flux solder”.
- Recommended temperatures for fine
wires and lead free solder is 300ºC.
For thicker wires, increase the
temperatures as necessary.

555
Spatulas
Use the spatula to eliminate the dross (Oxide
and other contaminants that form on the
surface of molten solder)
To stabilize the CT-SA place the spacers (lifters Ref. 0014899) between the support and the
workbench. This means you protect the rubber feet from wear and tear.
Use a screw (we recommend M4) and assemble washers and/or self-locking nuts.
Once fixed, check that the stand is stable and leveled.
Fixing the CT-SA
Lifters / spacers
self-locking nut
screw
washer
Workbench
The screw, washers and the self-locking nut are not included
www.jbctools.com

6
It is imperative to follow safety guidelines to prevent electric
shock, injury, fire or explosion.
6
6
- Do not use the appliance for any purpose other than to hold the solder pot. It is not a tool stand.
- Allow to cool before handling.
- Before inserting the cartridge, turn off the station. If T470 is used, insert the cartridge and tighten
the screw.
- Use on a level and stable surface.
- The stand can reach extreme temperatures. Glasses and protective gloves are mandatory.
- Do not melt “Cored Flux solder”.
- Recommended temperatures for fine wires and lead free solder is 300ºC. For thicker wires,
increase the temperatures as necessary.
- Do not leave the appliance unattended when it is running.
- Do not use next to flamable materials. Do not spill liquid into the solder pot.
- Turn off when not in use or not supervised.
- Avoid contact with moving parts.
- Keep your workplace clean and tidy.
- This appliance can be used by children aged from 8 years and above and persons with reduced
physical, sensory or mental capabilities or lack of experience and knowledge if they have been
given supervision or instruction concerning use of the appliance in a safe way and understand
the hazards involved. Children must not play with the appliance. Cleaning and user maintenance
must not be carried out by children without supervision.
- Utmost care must be taken with liquid tin waste which can cause severe burns.
- Be careful with the fumes produced when soldering.
Safety
Maintenance
Allow to cool before carrying out maintenance or storage. Always unplug the handle from the station
and remove it from the stand.
TrayProtective screen
- Use a damp cloth to clean the tray and the protective screen.
Alcohol can only be used for cleaning the metal parts.
- Replace any defective or damaged parts. Use original JBC spare parts only.
- Repairs should only be performed by a JBC authorized technical service.

7
7
7
Exploded View
www.jbctools.com

This product should not be thrown in the garbage.
In accordance with the European directive 2002/96/EC, electronic equipment at the end of their life
must be collected and returned to an authorized recycling facility.
Warranty
JBC’s 2 year warranty covers this equipment
against all manufacturing defects, including the
replacement of defective parts and labour.
Warranty does not cover product wear due to use
or mis-use.
In order for the warranty to be valid, equipment
must be returned, postage paid, to the dealer
where it was purchased.
Manual in other languages available on our website
0015011-0616
- Weight: 1.6 kg (3.5 lb)
- Dimensions: 50 x 246 x 92 mm
Complies with CE standards.
ESD protected housing “skin effect”.
Specifications
www.jbctools.comwww.jbctools.com