JIB 1316B User manual

MODEL 1316B/1316F
FOR YOUR SAFETY:
READ ALL INSTRUCTIONS CAREFULLY

Table of Contents
General safety instructions for Power Tools
…………………………………………
1
Main specification
…………………………………………………………………………
2
Unpacking and checking contents…………………………………………………… 2
List of loose parts in the box and bags………………………………………………. 3
Getting to know your drill press………………………………………………………
..
4
Assembly………………………………………………………………………………….. 5
Lubrication………………………………………………………………………………… 6
Maintenance……………………………………………………………………………… 6
Wire diagram……………………………………………………………………………… 6
Trouble shooting…………………………………………………………………………. 7
Repair parts……………………………………………………………………………….. 8
General safety instructions for Power Tools
1.KNOW YOUR POWER TOOL
Read and understand the ower's manual and labels affixed to the tool.Learn its application and
limitations as well as the specific potential hazards peculiar to this tool.
2.GROUND ALL TOOLS
This tool is equipped with an approved 3 conductor and a 3 prong grounding type plug to fit the
proper grounding type receptacle.
3.KEEP GUARDS IN PLACE
In working order and in proper adjustment and alignment.
4.WEAR PROPER APPAREL
Do not wear loose clothing,gloves,neckties,or jewelry (rings,wrist,watches) to get caught in moving
parts.Wear protective hair covering to contain long hair.Roll long sleeves above the elbow.
5.USE SAFETY GOGGLES
6.KEEP WORK AREA CLEAN
Cluttered areas and benches invite accidents.Floor must not be slippery due to wax or sawdust.
7.KEEP CHILDREN AWAY
-1-

Main Specification
Drill Capacity 16 mm / 5/8 in.
Chuck Capacity 16 mm / 5/8 in.
Swing 330 mm / 13 in.
Spindle Taper MT2
Spindle Travel 80 mm / 3-5/32 in.
Column Diameter 73 mm / 2-7/8 in.
Motor 120V/1ph/600W
Rack & Pinion Yes
Base Size 450 × 270mm / 17-23/32 × 10-5/8 in.
Table Size dia 300mm / 11-13/16 in.
Overall Height DP33016B: 990 mm / 38-31/32 in.
DP33016F: 1630mm / 64-11/64 in.
Range of spindle speeds
16 speeds
Motor Speed Spindle Speeds (min-1)
1700 min-1 220 300 430 480 590 650 720 850 900 950 1600 1900 2000
2500 2900 3600
Unpacking and checking contents
1.Unpacking and checking contents
Separate all the parts from packaging materials and check each item make sure all items are accounted
for before discarding any packing material.
Item Description Qty
A Table (square or Round )………………………. 1
B Column Support Asm……………………………. 1
C Owner's Manual…………………………………… 1
D Box of Loose Parts……………………………….. 1
E Bag of Loose Parts……………………………….. *
F Base…………………………………………………. 1
G Head Asm………..………………………………… 1
2.Remove the protective oil that is applied to the table and column.Use any ordinary household
type grease and spot remover
3.Apply a coat of paste wax to the table and column to prevent rust.Wipe all parts thoroughly with
clean dry cloth.
-2-

Separate all the parts from packaging materials and check each item make sure all items are accounted

List of Loose Parts in the box and bags
-3-

Getting to know your drill press
- 4-

Assembly
Refer to the figure install all parts correctly,
tighten the screw and bolts securelly.
1 Base
2. Column/w Support Asm
3 M10*1.5-40Screw (4)
4 Head Asm
5 Table
6 Feed Handle
7 Clamp-Column Lock
8 Crank
-5-
- 5-

Lubrication
All of the BALL BEARING are packed with grease at the factory.They require no further lubrication.
Periodically lubricate the table elevation machanism,the SPLINES (grooves) in the spindle,and the
RACK (teeth of the quill),see "Getting to know your drill press."
Maintenance
Frequently blow out any dust that may accumulate inside the motor.
A coat of automotive type paste was applied to the table and column will help to keep the surfaces clean.
Wire diagram
Part No. Component/Object Manufacturer PCS
Motor Motor AC250V/1PH/400W 1
SB1 Magnetic Switch 250VAC/16A 1 KJD12
SB2
SB3 Push Button-Emergency Stop 250VAC/12A 1 HY57B
SB4 Micro Switch 250VAC/16A 1 KW-7-3B
SB5 Micro Switch 250VAC/16A 1 KW7
- 6-

Trouble Shooting
TROUBLE PROBABALE CAUSE REMEDY
Noisy Operation
1.Incorrect belt tension. 1.Adjust tension.
2.Dry Spindle. 2.Lubricate spindle.
3.Loose spindle pulley 3.Checking tightness of retaining nut on
pulley,and tighten if necessary.
4.Loose motor pulley 4.Tighten setscrews in pulleys.
Drill bit burns
1.Incorrect speed. 1.Change speed.
2.Chips not coming out of hole. 2.Retract drill bit frequently to clear chips.
3.Dull drill bit 3.Resharpen drill bit.
4.Feeding too slow 4.Faster the speed.
5.Not lubricated 5.Lubricate drill bit.
Drill bit leads off…
hole not round
1.Hard grain in wood or
lengths of cutting lips
and/or angles not equal
1.Resharpen drill bit correctly.
2.Bent drill bit 2.Replace drill bit.
Wood splinters on
underside
1.No "back up material" 1.Use "back-up material"
under workpiece.
Workpiece turn
loose from hand
1.Not supported or 1.Support working or clamp it.
clamped properly.
Drill bit binds in
workpiece
1.Workpiece pinching drill bit 1.Support working or clamp it.
or excessive feed pressure.
2.Improper belt tension. 2.Adjust temsion.
Excessive drill bit
runout or wobble
1.Bent drill bit 1.Use a straight drill bit.
2.Worn spindle bearings. 2.Replace bearings.
3.Drill but not properly 3.Install drill bit properly.
installed in chuck
4.chuck not properly installed. 4.Install chuck properly.
Quill Returns too
slow or too fast 1.Spring has improper tension. 1.Adjust spring tension.
Chuck will not stay
atached to spindle
if falls off when
trying to install it.
1.Dirty,grease,or oil on the 1.Using a household detergent clean the
tapered inside surface of chuck tapered surface of the chuck and spindle to
or on the spindles tapered remove all dirt,grease and oil.
surface.
-7-

Repair Parts
FIGURE1
FIGURE1 PARTS LIST
Key
No. Description Key No. Description
1 Screw-Hex Soc.Set 11 Support Column
M6*1.0-10 12 Screw-Hex HD M10*1.5-40
2 Collar-Rack 13 Screw-Hex Soc.Set
3 Gear-Helical M10*1.5-12
4 Crank 14 Tube Column
6 Table 15 Rack
7 Clamp-Table 16 Clamp-Column
8 Screw-Hex HD 17 Support Table w/Indicator
M16*20-35 18 Worm-Elevation
9 Arm-Table w/Scale 19 Pin-Gear
10 Base
-8-