JMA Wireless 919050 User manual
81900510 Rev. B
©2019 JMA Wireless. All rights reserved. This document contains proprietary information. All products, company names, brands, and logos are trademarks™ or
registered® trademarks of their respective holders. All specificationsare subject to change without notice.Revised: July 8, 2019
Installation Guide
Venue
Bracket
JMA Wireless World
Headquarters
7645 Henry Clay Boulevard
Liverpool, NY 13088
USA
www.jmawireless.com
+1 888-201-6073
Instructions for Mounting Kits
919050, 919055, & 91900313
P/N 81900510
20
Rev. Description ECO number
ARelease
BUpdated to add SX
antenna views and
instructions for
91900313 bracket kit
75289 ECR00708
81900510 Rev. B
©2019 JMA Wireless. All rights reserved. This document contains proprietary information. All products, company names, brands, and logos are trademarks™ or
registered® trademarks of their respective holders. All specificationsare subject to change without notice.Revised: July 8, 2019
Installation Guide
Venue Brackets
Instructions for Mounting Kits 919050, 919055, & 91900313
This is the installation guide for the Venue Bracket. Note that
the bracket comes pre-installed on the antenna.
Antenna XGU-165 pictured for reference.
2 3
Figure 1: Bracket installed on antenna
Figure 2: 919050 kit
The bracket can be repositioned depending upon use in the field.
When mounting the antenna, always follow the arrows and the word
“top” for correct placement. When the bracket is in horizontal mount, the
word “top” marked on the bracket will match the top of the antenna. But
in vertical mount, the bracket can be turned either way. Torque 1/4” SS
hardware to 75 lbf∙in (8.47 N∙m).
81900510 Rev. B
©2019 JMA Wireless. All rights reserved. This document contains proprietary information. All products, company names, brands, and logos are trademarks™ or
registered® trademarks of their respective holders. All specificationsare subject to change without notice.Revised: July 8, 2019
Installation Guide
Venue Brackets
Instructions for Mounting Kits 919050, 919055, & 91900313
Kit #919050
Item
#JMA part # Description Qty.
in kit
1411-144-0732-VS 10-32 x 1/2” HEX Head Bolt
SS 2
2411-144-1348-VS 3/8”-16 x 1.000” HEX HEAD
BOLT FULL THRE 4
3412-105-0907-VS 1/4”-20 HEX NUT SS 4
4413-011-1699-VS 1/4 FLAT WASHER SS 4
5413-011-2421-VS 3/8” FLAT WASHER SS
(OD 13/16) 4
6413-011-8518-VS #10 FLAT WASHER SS 2
7413-012-1659-VS 1/4 SPLIT LOCK WASHER SS 4
8413-012-2489-VS 3/8 SPLIT LOCK WASHER SS 4
9413-012-6789-VS #10 SPLIT LOCK WASHER
SS 2
10 457216-PF Wall / Pipe Mount Stadium
Bracket 1
11 457217-PF Center Mount Stadium
Bracket 1
12 457218-PF Antenna Mount Stadium
Bracket 1
13 81900510 Assembly instructions 1
Other key details:
The brackets were designed to handle pole diameters ranging from
2.5 to 4.5 inches.
All 10-32 hardware to be torqued to 30 lbf∙in (3.39 N∙m).
All 3/8” hardware to be torqued to 20 lbf∙ft (27.12 N∙m).
All 1/4” hardware to be torqued to 75 lbf∙in (8.47 N∙m).
Fasteners / hose clamps for wall mount and pole mount not
included in 919050 bracket kit. (Sold separately)
Below is the bracket kit pre-installed on the antenna.
45
Venue bracket details.
Bracket 12 can be re-oriented 90°to support vertical mounting
configurations. Keep the word “top” on the antenna facing top, and the
weep hole facing down. Use Screw 1 for locking bracket into specific
angle positions. Torque to 30 lbf∙in (3.39 N∙m). Use the holes in Bracket
10 (4.50” [114.3 mm] apart @ CL) and 3/8” hardware for wall mounts.
Figure 3: Bracket details
81900510 Rev. B
©2019 JMA Wireless. All rights reserved. This document contains proprietary information. All products, company names, brands, and logos are trademarks™ or
registered® trademarks of their respective holders. All specificationsare subject to change without notice.Revised: July 8, 2019
Installation Guide
Venue Brackets
Instructions for Mounting Kits 919050, 919055, & 91900313
Wall-mounted bracket
See Figure 2, the bracket drawing, for the hole layout dimensions. All
3/8” hardware to be torqued to 20 lbf∙ft (27.12 N∙m).
6 7
Figure 4: Wall mount
Pole-mounted bracket
Figure 5: Pole mount
Plan view
Bracket
attaches to
wall using
appropriate
3/8” fasteners
suitable for
wall structure
(2 places
each) Torque
to 20 lbf∙ft
(27.12 N∙m)
Side view
Plan view
Side view
Bracket
attaches to
pole using
appropriate
pole straps
(4 places
each)
81900510 Rev. B
©2019 JMA Wireless. All rights reserved. This document contains proprietary information. All products, company names, brands, and logos are trademarks™ or
registered® trademarks of their respective holders. All specificationsare subject to change without notice.Revised: July 8, 2019
Installation Guide
Venue Brackets
Instructions for Mounting Kits 919050, 919055, & 91900313
Vertical and horizontal mounting positions tables
Azimuth rotation for specific locking position. Use supplied #10-32
fasteners to lock bracket at specific angle.
Figure 6: Bracket azimuth rotation in vertical position
Mechanical downtilt rotation for specific locking position. Use supplied
#10-32 fasteners to lock bracket at specific angle.
8 9
Figure 7: Bracket mechanical downtilt rotation in horizontal
position
+ve side
-ve side
“-” indicates
negative angle
-ve side
+ve side
81900510 Rev. B
©2019 JMA Wireless. All rights reserved. This document contains proprietary information. All products, company names, brands, and logos are trademarks™ or
registered® trademarks of their respective holders. All specificationsare subject to change without notice.Revised: July 8, 2019
Installation Guide
Venue Brackets
Instructions for Mounting Kits 919050, 919055, & 91900313
10 11
Optional inverted (upside down) mount kit (919055).
Maximum angle for wall-and pole-mount antennas.
Figure 8: Maximum angle indicated in table
Angle “X”Angle “X”
Angle “Y”
Angle “Y”
This bracket kit 919055 to be used along with venue bracket 919050 on
poles with an outer diameter of 4”-10”. Refer to page 10 to learn about
available tilt options. All 3/8”-16 fasteners to be torqued to 20 lbf∙ft
(27.12 N∙m). Must use appropriate size heavy duty band straps. While
mounting antenna upside down, additional weep holes must be drilled
to properly drain antenna. Refer to JMA weep hole modification guide at
jmawireless.com
Kit #919055
Item
#JMA part # Description Qty.
in kit
1411-144-1350-VS 3/8”-16 x 1-1/4” HEX BOLT
FULL THREAD SS 2
2412-105-1322-VS 3/8”-16 HEX NUT SS 2
3413-011-2421-VS 3/8 FLAT WASHER SS
(OD 13/16) 2
4413-012-2489-VS 3/8 SPLIT LOCK WASHER SS 2
5457237-PF BRACKET, INVERTED MNT
919050 STDM BRCKT 1
681900510 Instructions for mounting
kits 919050 and 919055 1
NOTE: These item numbers refer to Figure 10.
81900510 Rev. B
©2019 JMA Wireless. All rights reserved. This document contains proprietary information. All products, company names, brands, and logos are trademarks™ or
registered® trademarks of their respective holders. All specificationsare subject to change without notice.Revised: July 8, 2019
Installation Guide
Venue Brackets
Instructions for Mounting Kits 919050, 919055, & 91900313
12 13
Below is the optional bracket kit 919055 for inverted
mount.
Figures 9 and 10 show both kits 919050 and 919055 together. XGU
model antenna pictured for reference.
Figure 9: Inverted mount
Figure 10: Inverted mount: side view details
Band straps
(2 places)
(not included
in kit)
Inverted mount bracket kit
P/N 919055
Pre-installed
venue bracket kit
3/8” hardware torque:
20 lbf∙ft (27.12 N∙m).
* Approximate dimensions
81900510 Rev. B
©2019 JMA Wireless. All rights reserved. This document contains proprietary information. All products, company names, brands, and logos are trademarks™ or
registered® trademarks of their respective holders. All specificationsare subject to change without notice.Revised: July 8, 2019
Installation Guide
Venue Brackets
Instructions for Mounting Kits 919050, 919055, & 91900313
14 15
Below is the optional extension bracket kit 91900313
for inverted mount of larger antennas.
Figure 11 shows antenna SX08FRO230-01 (for reference only) pictured
after being fitted with extension bracket kit 91900313.
Figure 11: Inverted mount
Figure 13: Connecting the
extension bracket to the antenna
mount stadium bracket
Extension kit
91900313
Antenna mount
stadium bracket
3/8”-16 hardware,
4 PL as shown
Center mount
stadium bracket
#10-32 screw, 2 PL (for locking
bracket into specific angle
position
Wall/pipe mount
stadium bracket
Step 1: Removing the wall/pipe mount bracket from the antenna
mount stadium bracket. Do not throw away any hardware. Remove 2
sets of 3/8”-16 hardware and the #10-32 screw from the connection of
the center mount stadium bracket and wall/pipe mount stadium bracket.
Remove the wall/pipe mount bracket from the assembly.
Step 2: Installing the extension bracket. Install extension bracket
kit 91900313 by securing the extension bracket to the center mount
stadium bracket using 3/8” hardware and #10-32 screw from Step 1. All
3/8” hardware to be torqued to 20 lbf∙ft.
Figure 12: Removing the
wall/pipe mount bracket
Wall mount holes,
2 PL, using 3/8”
hardware, 4.50”
apart @ centerline
81900510 Rev. B
©2019 JMA Wireless. All rights reserved. This document contains proprietary information. All products, company names, brands, and logos are trademarks™ or
registered® trademarks of their respective holders. All specificationsare subject to change without notice.Revised: July 8, 2019
Installation Guide
Venue Brackets
Instructions for Mounting Kits 919050, 919055, & 91900313
16 17
Vertical and horizontal mounting positions tables
Azimuth rotation for specific locking position. Use supplied #10-32
fasteners to lock bracket at specific angles, at 5-degree increments, (+)
& (-) sides.
Mechanical downtilt rotation for specific locking position. Use supplied
#10-32 fasteners to lock bracket at specific angle.
“-” indicates
negative angle
Figure 14: Bracket azimuth rotation in vertical position
Figure 15: Bracket mechanical
downtilt rotation in horizontal
position
+ve side
-ve side
AZIMUTH ROTATION TABLE
LEGEND AZIMUTH
ROTATION (DEG)
A 0
B 5
C10
D15
E20
F25
G30
MECH. DOWNTILT TABLE
LEGEND DOWNTILT
ROTATION (DEG)
A 0
B 5
C10
D15
E20
F25
G30
H35
I40
J45
K50
L55
-ve side
+ve side
81900510 Rev. B
©2019 JMA Wireless. All rights reserved. This document contains proprietary information. All products, company names, brands, and logos are trademarks™ or
registered® trademarks of their respective holders. All specificationsare subject to change without notice.Revised: July 8, 2019
Installation Guide
Venue Brackets
Instructions for Mounting Kits 919050, 919055, & 91900313
18 19
Below is the optional extension bracket kit 91900313 for
inverted mount of larger antennas.
Figures 16 and 17 show both kits 919050 and 91900313 together. XGU
model antenna pictured for reference.
Figure 16: Inverted mount
Figure 17: Inverted mount: side view details
Band straps
(2 places)
(not included
in kit)
Inverted mount bracket kit
P/N 919055
Extension bracket kit
P/N 91900313
3/8”
hardware
torque:
20 lbf∙ft
(27.12 N∙m)
* Approximate dimensions
This manual suits for next models
2
Table of contents
