Kenmore 721.85062 User manual

ENGLISH ESPAÑOL
Models/Modelos
721.85062
721.85063
721.85064
721.85069
Read and save these
installation instructions.
Lea y guarde estas
instrucciones de
instalación
  
INSTALLATION INSTRUCTIONS
INSTRUCCIONES DE INSTALACIÓN



2
ENGLISH
YOUR SAFETY FIRST
BEFORE YOU START

- Read the entire manual before you begin.
- The model number label is located on the oven front of oven behind doon See Figure 1.
- Mounting plate is located on back side of microwave oven. See Figure 2.
BE SURE TO READ THE FOLLOWING SAFETY INSTRUCTIONS:
Model Number Label
Model Number Label
Mounting Plate
Mounting Plate
Figure1 Figure 2
FOR YOUR SAFETY:
• This oven should not be installed or located by anyone except properly qualified service personnel.
• You will need TWO people to install this oven. It is heavy and could cause personal injury if not
handled properly.
• 
- Before you drill into the wall, note where electrical outlets are and where electrical wires might be
behind concealed the wall, YOU COULD GET AN ELECTRIC SHOCK it you contact electrical wires
with your drill bit.
- Locate and disconnect the power of any electrical circuits that could be aected by installing this oven.
IF YOU DO NOT DISCONNECT THE POWER, YOU COULD GET AN ELECTRIC SHOCK.
• ELECTRICAL RATING OF THIS OVEN: 120V, 60Hz.
- You need a 120V, 60Hz, AC only, 15A or 20A, fused electrical supply (located in the cabinet above
the microwave as close as possible to the microwave circuit) serving only the microwave.
WARNING

3
ENGLISH
YOUR SAFETY FIRST
ENGLISH



- Check with a qualified electrician if you are not sure whether the oven is properly grounded or if you
do not completely understand the grounding instructions.
DO NOT USE A FUSE IN THE NEUTRAL OR GROUNDING CIRCUIT.

SAVE THESE INSTRUCTIONS FOR THE LOCAL ELECTRICAL INSPECTOR'S USE.
• 
- DO NOT try to operate the microwave oven with the door open.
- DO NOT tamper with or defeat the safety interlocks.
- DO NOT place objects between the microwave oven front face and the door.
- DO NOT allow soil or cleaner residue to build up on the flat surfaces around the microwave oven door.
- DO NOT operate the microwave oven if it is damaged.
- The microwave oven door must close properly to operate safely.
- DO NOT use the microwave oven:
• If the door is bent.
• If the hinges or latches are broken or loose.
• If the door seals, sealing surfaces or glass is broken.
- DO NOT attempt to adjust or repair the oven yourself!
It should be adjusted and repaired by a qualified technician who can check for microwave leakage
after repairing the oven.

- If there is an electrical short circuit, grounding reduces the risk of electrical shock by providing an
escape wire for the electric current. This appliance is equipped with a cord having a grounding
wire with a grounding plug.
• Place the plug into a properly installed and grounded outlet.
See Figure 3.
• Do not use an extension cord.
• Keep the power cord dry and do not pinch or crush it.


This appliance MUST be grounded!
PROPERLY POLARIZED AND
GROUNDED OUTLET
Three-Pronged (Grounding) plug
Figure 3
WARNING
WARNING
WARNING

YOUR SAFETY FIRST
4
ENGLISH

- Mount the oven against a flat, vertical wall, so that it is supported by the wall. The wall should be
constructed of minimum 2" x 4" wood studding and 3/8" thick drywall or plaster/lath.
- ATTACH AT LEAST ONE of the two lag screws supporting the oven to a vertical, 2" x 4" wall stud.
- DO NOT mount the microwave oven to an island or peninsula cabinet.
- BE SURE the upper cabinet and rear wall structures are able to support 150 lbs., plus the weight of
any items you place inside the oven or upper cabinet.
- Locate the oven away from strong draft areas, such as windows, doors, and strong heating vents.
- BE SURE you have enough space. See Figure 4 below for minimum vertical and horizontal clearance.


WARNING
• Before you begin installing the oven, PLACE A PIECE OF THE CARTON OR OTHER HEAVY MATERIAL
(a blanket) over the countertop or cooktop to protect it. 
Failure to protect these surfaces could result inproperty damage.
CAUTION
Grounded Plug


Cord Hole


of cabinet to cooking surface or



Figure 4

5
ENGLISH
PARTS, TOOLS, MATERIALS
12

REAR WALL TEMPLATE
B.
A.
F. CUT OUT FOR WALL
VENTED ONLY
12

REAR WALL TEMPLATE
B.
A.
F. CUT OUT FOR WALL
VENTED ONLY
ENGLISH
THE FOLLOWING PARTS ARE SUPPLIED WITH THE OVEN:
NOTE: Depending on your ventilation requirements, you may not use all of these parts.
12

REAR WALL TEMPLATE
B.
A.
F. CUT OUT FOR WALL
VENTED ONLY
12

REAR WALL TEMPLATE
B.
A.
F. CUT OUT FOR WALL
VENTED ONLY
12

REAR WALL TEMPLATE
B.
A.
F. CUT OUT FOR WALL
VENTED ONLY
12

REAR WALL TEMPLATE
B.
A.
F. CUT OUT FOR WALL
VENTED ONLY

(for roof vented or wall vented installation).
Not Actual Size (2 pieces must be assembled
as shown)

(for wall stud holes).
Not Actual Size
(3 pieces mounting plate only)


(for securing to the upper cabinet).

(for the toggle bolts).
NOTE: You need to install at least two lag screws into a 2" x 4" stud and four anchor bolts into the wall.
and the mounting area must meet the 150 lbs. weight requirement.

(for drywall holes).

- Not Actual Size

(for the cord hole in a metal upper cabinet).


(to hold the power cord).
Actual Size

(for attaching the damper duct connector)
12

REAR WALL TEMPLATE
B.
A.
F. CUT OUT FOR WALL
VENTED ONLY