Kid's Creations Costco High Wire 2254 Quick start guide

52011
Costco High Wire
Assembly InstrucƟons & Owner's Manual
Important!
Read this manual completely through before assembly and use.
Consumer assistance
Toll free – If you need to order replacement parts or have any questions or concerns about your
Kid’s Creations product; Call 1-800-437-0784.
Warning: Installation over a hard surface such as concrete, asphalt or packed earth
may result in serious injury or death from falls
Copyright Kids Creations, L.L.C., Garnett, Kansas
2254

High Wire - Parts List
PALLE
T
QTY
3144 5' Rock wall 1
3120 Deck Panel 8
3130 Ladde
r
1.
#8 Deck Support 4
#27A Top Canop
y
Support 1
#102 Wood canop
y
Face Board 4
#25 Tower End Brace 5
#28 Canop
y
Upri
g
ht 1
#4 Ri
g
ht Hand Brace 3
#5 Left Hand Brace 3
#6 Handrail Support Post 3
#14 Deck Facer Board 5
#50 Handrail 1
#23 A-frame Block 1
#101 Wood Roof Slat 22
#52 Beam Connectin
g
Post 1
Swin
g
s - Green 3
Rocks
(
12
)
1
Safet
y
Handles Pai
r
2
Steerin
g
Wheel 1
Telescope 1
Tire Swin
g
1
Glide
r
0
#70 Balcon
y
Deck Supports 2
#81 Balcon
y
Facer Board 2
#95 Slide Face Mount 1
#96 Slide Face Mount 1
#97 Slide Face Mount 1
#2 Tower Base Board 1
#3 Tower Base Board 2
#7 Tower Facer Board 5
#9 Deck Board 5
3122 Small Rails 6
3124 Lar
g
e Rails 4
3125 Handrail C 2
3134 45 De
g
ree Ladde
r
1
3132 3 Run
g
Ladde
r
1
Bolt Bo
x
1

BUNDLE #1 QTY
#48 Swin
g
Beam 1
#1 Tower Le
g
4s
A
BUNDLE #
2
#26 Canop
y
Support 2
#22 A-frame Support 1
#24 A-frame Le
g
2
#80 Canop
y
Upri
g
ht 1
BUNDLE #3
#34 Tower Le
g
4s
#51 Tower Base Board 2
SLIDE BUNDLE
S
1edilSebuT
14' Green Slide 1
14' Blue Slide 1
BOLT BOX
11"
x 1/2" Bolt 6
9"
x 1/2" Bolt 1
7"
x 1/2" Bolt 80
5" x 1/2" Bolt 34
3 1/2" x 1/2" Bolt 8921stuN"2/1
1/2" Washers 129
513swercS"3
4" La
g
Screws 10
La
g
Washers 10
Slide Screws 6
Star Head Drive
r
1
Snap Hooks 8
7" x 3/8" Carria
g
e Bolt 12
3/8" Flat Washe
r
12
3/8" Lock Nut 12
3/8" Torque Washe
r
12

NOT
E
:ALLBOLTSGETAWASHER,LOCKWASHER,ANDANUT
INTHISORDER.
Prior to construction:
Follow each assembly instruction in this booklet very carefully and
thoroughly.
Open all packages and parts bags and lay all parts that look the same
together.
Before using play center, review all maintenance and safety play tips
and inspect for proper and complete assembly.
Wear safety glasses at all times during assembly.
Configuration shown may be altered according to layout desired and
area placed
Note: Bolts were designed to be very snug when inserted into pre-drilled
holes. Use of a hammer will be necessary.

Parts needed for step 1
(4) Part #34 119 ¾” 4x4
(2) Part #26A 7’6” 4x4
(2) Part #8 4’ 10” 4x6
1. Using 7” bolts, connect part #8 to 2 of part #34’s with counter
sink on part #34 facing inward. Counter sink on part #8 should be facing up.
2. Using 7” bolts, connect part #26A to 2 parts #34’s. Note: etacoL
counter sinks on part #26A – they should be facing DOWN.
3. Tighten all connec ons and repeat for opposite side.
#26A
#34
#8
NOTE: Place all bolts so they have the nut in the counter sink part of
the board, so they will not stick out and harm anyone.
Countersink
Inward
Countersink up
Countersink

Partsneededforstep2
(1)Part#286'5"4x4
1.Connectpart#28asshownwith7"bolts.
#28

Partsneededforstep3
(1)Part#808'5"4x4
1.Connectpart#80toothersideasshownwith7"bolts.
#80

80
28

Partsneededforstep4
(2)Part#75'6"2x6
1.Donottightenbolts.
2.Standupbothtowerframesmadeinearliersteps2and3.Note:Part#8
(4x6)onbothtowerlegsshouldbeontheinsideofthetower.
3.Using5"bolts,connectpart#7tobothtowers.
#80
#28
#7
#7

Partsneededforstep5
(1)Part#34'10"2x6
(1)Part#42'2"4x4
(1)Part#52'2"4x4
1.Facingthe2x6(part#7)using5"and31/2"bolts,connectpart#4to
therighthandsideandconnectpart#5tothelefthandside.
2.Using3"screwsconnectpart#3tothesideoftowerwithpart#28.
3.Usingalevelandsquare,squareupswingsetandtightenallbolts.
#4
#5
#3

Partsneededforstep6
(1)Part#84'10"4x6
1.Using7"boltsconnectpart#8tothetowerasshown.
Note:Thecountersinkonpart#8shouldfaceout.
#8
These twoboltswillbereplacedby
11"boltsinalaterstep.

Note:
Note:
#1
#8
#50
Countersink
Direc ons

Partsneeddforstep8
(1)Part#34'10"2x6
(1)Part#75'6"2x6
(2)Part#511311/2"2x6
1.Using5"boltsconnectpart#7tomaintowerthenstandup
endframeandconnecttootherendofpart#7.
2.Using5"boltsattachparts#51totowerlegsasshown.
3.Using3"screwsattachpart#3asshown.
#51
#3
#51
#7

Partneededinstep9
(1)Part#42'2"4x4
(2)Part#52'2"4x4
1.Facingthe2x6(part#7)connectpart#4totherighthandsideusing
5"and31/2"boltsconnect#5tothelefthandslide.
2.Connectrockwalltotower,using11"bolts.Theexistinglower7"
boltsplacedinthe#8willberemovedandreplacedwiththe11"bolts.
3. To attach rocks, place rocks in random pattern by using the 1-1/2" screw in the
small hole of the rock to place the rock.
4. After you have connected the rocks to the rock wall with the little screw, rotate
the rock where you want it. Use the 2" screw and washer in the large hole of
the rock to set the rock in place.
#5
#4

Partsneededforstep10
(2)Part#94'11"2x6
1.Placedeckboardsontopof4x6(part#8)andplace#9'sontheoutside.
2.Using3"screws;screweach2x6deckboardintothe4x6below.
Use2screwsoneachendofdeckboard.
#9
#9
Deck panels

Partneededforstep11
(2)Part#94'11"2x6
1.Attachdeckinginsamemannerasstep10using3"screws.
#9
#9
Deck panels

Partneededforstep12
1.Attachsmallladderasshownusing3"screws.