Knectek Labs CubiTag CTAG0302 User manual

Cautions
RISK OF EXPLOSION: If battery is replaced with incorrect
type. Dispose of used batteries according to instructions.
Cautions
CHOKING HAZARD: Small parts, particularly coin cell
battery and battery cap. Please use with caution
around young children and pets.
Ring your phone by double-clicking here
・ Location of Push-button ・ Battery Replacement
CubiTag is a trademark of Knectek Labs Inc.
©2017 Knectek Labs Inc. All Rights Reserved.
Made in China
Visit
cubitag.com
[ USER MANUAL ]
Card
Model: CTAG0302
Manufacturer: KNECTEK LABS INC.
push-button
Slide open the battery cover.
loosen the screw
push down

QUICK START GUIDE
1. Download the CubiTag app from the App Store or
Google Play by scanning the QR Code below:
2. Add CubiTag Card by following the instructions on
the CubiTag app.
3. Attach CubiTag Card to your items and find them at
the click of a button on the CubiTag app, or find your
phone by double-clicking the CubiTag Card tracker.
CERTIFICATIONS & APPROVALS
This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful
interference to radio communications. However, there is
no guarantee that interference will not occur in a
particular installation. If this equipment does cause
harmful interference to radio or television reception,
which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment
and receiver.
- Connect the equipment into an outlet on a circuit
different from that to which the receiver is
connected.
- Consult the dealer or an experienced radio/TV
technician for help.
Changes or modifications not expressly approved by the
party responsible for compliance could void the user’s
authority to operate the equipment. This equipment
complies with FCC radiation exposure limits set forth for
an uncontrolled environment. This equipment should be
installed and operated with a minimum distance of 20
cm between the radiator and a human body.
FCC Statement
This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) this device must accept any interference received,
including interference that may cause undesired
operation.
NOTE: This equipment has been tested and found to
comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against
harmful interference in a residential installation.
Industry Canada (IC) Compliance Notice
This device complies with Industry Canada
license-exempt RSS standard(s). Operation is subject to
the following two conditions: (1) this device may not
cause interference, and (2) this device must accept any
interference, including interference that may cause
undesired operation of the device.
Avis de conformité à la réglementation d'Industrie
Canada
Le présent appareil est conforme aux CNR d'Industrie
Canada applicables aux appareils radio exempts de
licence. L'exploitation est autorisée aux deux conditions
suivantes: (1) l'appareil ne doit pas produire de
brouillage, et (2) l'utilisateur de l'appareil doit accepter
tout brouillage radioélectrique subi, même si le
brouillage est susceptible d'en compromettre le
fonctionnement.
CE Compliance
Knectek Labs Inc. hereby declares that CubiTag Card
conforms with all necessary requirements and EN
60950-1 standards. Model number and manufacturer’s
info can be found on the back of CubiTag Card.
Importer: Intretech Hungary Kft
Harmat u 208, 1108 Budapest, Hungary
WARRANTY SERVICE
Each CubiTag Card comes with One Year warranty
service. Consumers requesting repairs under warranty
must email [email protected] to obtain a Return
Merchandise Authorization (RMA).
Please visit cubitag.com/pages/return-policy-warranty
for more info.
SAFETY INSTRUCTIONS
・ To track your items, CubiTag Card requires the app to
be running in the background. Make sure the app is
running at all times. When the app is not running,
CubiTag will send a notification to let you know.
・ When replacing the battery, please replace with coin
cell battery CR2016 ONLY.