KODA Citigo User manual

SIMPLY CLEVER
ŠKODA Citigo
Owner's Manual

Layout of this Owner's Manual
(explanations)
This Owner's Manual has been systematically designed to make it easy for you to
search for and obtain the information you require.
Chapters, table of contents and subject index
The text of the Owner's manual is divided into relatively short sections which are
combined into easy-to-read chapters. The chapter you are reading at any particular
moment is always specified on the bottom right of the page.
The Table of contents is arranged according to the chapters and the detailed Sub-
ject index at the end of the Owner's Manual helps you to rapidly find the informa-
tion you are looking for.
Direction indications
All direction indications such as “left”, “right”, “front”, “rear” relate to the direction of
travel of the vehicle.
Units of measurement
All values are expressed in metric units.
Explanation of symbols
Denotes a reference to a section with important information and safety
advice in a chapter.
Denotes the end of a section.
Denotes the continuation of a section on the next page.
Indicates situations where the vehicle must be stopped as soon as possi-
ble.
® Denotes a registered trademark.
Notes
WARNING
The most important notes are marked with the heading WARNING. These
WARNING notes draw your attention to a serious risk of accident or injury.
CAUTION
A Caution note draws your attention to the possibility of damage to your vehicle
(e.g. damage to gearbox), or points out general risks of an accident.
For the sake of the environment
An Environmental note draws your attention to environmental protection aspects.
This is where you will, for example, find tips aimed at reducing your fuel consump-
tion.
Note
A normal Note draws your attention to important information about the operation
of your vehicle.

Preface
You have opted for a ŠKODA – our sincere thanks for your confidence in us.
You have received a vehicle with the latest technology and range of amenities. Please read this Owner's
Manual carefully, because the operation in accordance with these instructions is a prerequisite for proper use
of the vehicle.
Observe the national legal requirements when using your vehicle.
If you have any questions about your vehicle, please contact a ŠKODA Partner.
We hope you enjoy driving your ŠKODA, and wish you a pleasant journey at all times.
Your ŠKODA AUTO a.s. (Hereinafter referred to only as ŠKODA or manufacturer) 

On-board literature
The on-board literature for your vehicle consists of this “owner's manual” as well
as a “service schedule” and the “Help on the road” brochure.
Depending on the vehicle model and equipment, other additional operating man-
uals and instructions may be provided (e.g. an operating manual for the radio).
If one of the documents listed above is missing, please contact a ŠKODA Partner.
Terms used
The on-board literature contains the following terms relating to the service work
for your vehicle.
›“Specialist garage” - a company that carries out specialist service tasks for
ŠKODA vehicles
›“ŠKODA service partner” - a company that is contractually authorized by ŠKODA
AUTO a.s. to carry out service tasks for ŠKODA vehicles
›“ŠKODA Partners” - a company that is authorized by ŠKODA AUTO a.s. to sell
ŠKODA products or carry out service work, or to carry out these tasks in parallel
The owner's manual
This owner's manual describes all possible equipment variants without identify-
ing them as special equipment, model variants or market-dependent equipment.
Consequently, this vehicle does not need to contain all of the equipment compo-
nents described in this owner's manual.
The scope of equipment in your vehicle relates to your sales contract for the vehi-
cle. More information is available from the ŠKODA Partner where you bought the
vehicle.
The illustrations may differ in minor details from your vehicle; they are only inten-
ded as general information.
The service schedule:
›Contains vehicle data including information on service work carried out;
›Is intended as proof of services carried out;
›Is intended for records relating to the mobility warranty (only valid for some
countries);
›Serves as a warranty certificate from the ŠKODA Partner where your vehicle
was purchased.
Therefore please always present the service schedule when you take your vehicle
to a specialist garage.
If the service schedule is missing or in poor condition, please contact the special-
ist garage that regularly services your vehicle. You will need to request a dupli-
cate, in which the specialist garage will confirm the service work previously car-
ried out.
The Help on the road brochure
The Help on the road brochure contains the most important emergency tele-
phone numbers as well as telephone numbers and contact addresses of ŠKODA
Partners in the various different countries.

Table of Contents
Abbreviations
Using the system
Cockpit 7
Overview 6
Instruments and warning lights 8
Instrument cluster 8
Multifunction display (onboard computer) 11
Warning lights 14
Unlocking and locking 20
Unlocking and locking 20
Central locking system 23
Remote control 25
Luggage compartment lid 26
Window operation 27
Power sliding/tilting roof 29
Lights and visibility 31
Lights 31
Interior lighting 34
Visibility 35
Windscreen wipers and washers 36
Rear window 38
Seats and stowing 40
Front seats 40
Rear seats 42
Luggage compartment 44
Roof rack system 47
Useful equipment 48
Storage compartments 51
Heating and air-conditioning 55
Heating, ventilation, cooling 55
Heating 56
Air conditioning system 57
Communication and multimedia 60
Telephone and Move & Fun 60
Driving
Starting-off and Driving 63
Starting and stopping the engine 63
Braking 65
Manual gear changing and pedals 67
Automatic gearbox 67
Running in 70
Economical driving and environmental
sustainability 71
Avoiding damage to your vehicle 75
Driving abroad 76
Assist systems 77
Brake assist systems 77
Parking aid 78
Cruise Control System 80
START/STOP 82
City Safe Drive 83
Safety
Passive Safety 87
General information 87
Correct seated position 88
Seat belts 91
Using seat belts 91
Inertia reels and belt tensioners 93
Airbag system 95
Description of the airbag system 95
Airbag overview 96
Deactivating airbags 98
Transporting children safely 100
Child seat 100
Fastening systems 102
General Maintenance
Taking care of and cleaning the vehicle 105
Washing your car 105
Taking care of your vehicle exterior 106
Taking care of the interior 110
Modifications, repairs and technical alterations 112
Inspecting and replenishing 115
Fuel 115
Vehicles with CNG (compressed natural gas)
mode 116
Engine compartment 120
Engine oil 123
Coolant 125
Brake fluid 126
Vehicle battery 127
Wheels 131
Tyres and wheel rims 131
Winter operation 136
Do-it-yourself
Emergency equipment and self-help 137
Emergency equipment 137
Changing a wheel 138
Breakdown kit 142
3
Table of Contents

Jump-starting 144
Towing the vehicle 146
Fuses and light bulbs 148
Fuses 148
Bulbs 151
Technical data
Technical data 155
Vehicle data 155
Index
4Table of Contents

Abbreviations
Abbreviation Definition
rpm Engine revolutions per minute
ABS Anti-lock brake system
ASG Automated transmission
CNG Compressed natural gas
CO2 in g/km discharged quantity of carbon dioxide in grams per driven kilo-
metre
EDL Electronic differential lock
EPC EPC fault light
ESC Electronic Stability Control
kW Kilowatt, measuring unit for the engine output
MG Manual gearbox
MFD Multifunction display
Nm Newton meter, measuring unit for the engine torque
TCS Traction control 
5
Abbreviations

Fig. 1 Cockpit
6Using the system

Using the system
Cockpit
Overview
Door opening lever on the driver's side 22
Electrical power window in the driver's door 27
Central locking system 24
Electric exterior mirror adjustment 39
Air outlet vent on the driver's side 55
Operating lever:
›Turn signal lights and main beam, headlight flasher 32
›Speed regulating system 80
Steering wheel:
›With horn
›With driver’s front airbag 96
Instrument cluster: Instruments and warning lights 8
Operating lever:
›Multifunction display 11
›Windscreen wiper and wash system 36
Switch for rear window heater 35
START-STOP button 82
Depending on equipment fitted:
›Operating controls for the heating 56
›Operating controls for the air conditioning system 57
Socket for the cradle for the multifunction device Move & Fun 61
Warning light for the deactivated front seat passenger airbag 99
Interior mirror 38
Switch for hazard warning lights 33
Storage compartment on the front passenger side 52
Front passenger airbag 96
Air outlet vent on the front passenger side 55
Power window in the front passenger door 27
Door opening lever on the front passenger side 22
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
Light switch 31
Bonnet release lever 120
Regulator for headlamp beam adjustment for the headlights 32
Lever for adjusting the steering wheel 64
Ignition lock 65
Pedals 67
Regulator for left seat heating 42
Radio
Button for City Safe Drive system 83
Handbrake lever 66
Depending on equipment fitted:
›Gearshift lever (manual gearbox) 67
›Selector lever (automated gearbox) 69
Storage compartment 53
Regulator for right seat heating 42
Note
■Cars with factory-fitted radio are supplied with separate instructions for operat-
ing such equipment.
■The arrangement of the controls and switches and the location of some items
on right-hand drive models may differ from that shown in » Fig. 1. The symbols on
the controls and switches are the same as for left-hand drive models. 
22
23
24
25
26
27
28
29
30
31
32
33
34
7
Cockpit

Instruments and warning lights
Instrument cluster
Introduction
This chapter contains information on the following subjects:
Overview of the Instrument cluster 8
Speedometer 9
Fuel gauge 9
Engine revolutions counter 9
Counter for distance driven 10
Service Interval Display 10
Recommended gear 10
WARNING
■Concentrate fully at all times on your driving! As the driver you are fully re-
sponsible for the operation of your vehicle.
■Never operate the controls in the instrument cluster while driving, only
when the vehicle is stationary! 
Overview of the Instrument cluster
Fig. 2 Instrument cluster - Version 1
Fig. 3 Instrument cluster - Version 2
First read and observe the introductory information and safety warn-
ings on page 8.
Speedometer » page 9
Display:
›With counter for distance driven » page 10
›with outside temperature display » page 12 

1
2
8Using the system

›With service interval display » page 10
›With multifunction display » page 11
Reset button for the display of the daily trip counter (trip) » page 10
Fuel gauge » page 9
Engine revolutions counter » page 9
Adjust button for the clock » page 12 
Speedometer
First read and observe the introductory information and safety warn-
ings on page 8.
The speed is shown in km/h or mph and km/h depending on the vehicle. 
Fuel gauge
Fig. 4 Fuel gauge
Fig. 5
Fuel gauge - CNG
3
4
5
6

First read and observe the introductory information and safety warn-
ings on page 8.
Vehicles running on petrol
The fuel gauge » Fig. 4 only operates if the ignition is switched on.
The fuel tank has a capacity of about 35 litres. If the fuel gauge in the fuel tank
reaches the reserve capacity level, the warning symbol  » Fig. 4 -  will appear
in the Instrument cluster. or the symbol  will flash for 10 seconds together with
the remaining segments in the instrument cluster display » Fig. 4 - . There are
now about 4 litres of fuel remaining in the tank. This symbol is a reminder for you,
that you must refuel.
An audible signal sounds as a warning signal.
Vehicles running on CNG (compressed natural gas)
The fuel gauge » Fig. 5 only operates if the ignition is switched on.
When the vehicle runs on petrol, the pointer of the fuel gauge is in the range
1 » Fig. 5. When the vehicle runs on CNG, the pointer of the fuel gauge is in the
range 2.
If the fuel level in the fuel tank for petrol reaches the reserve level, the warning
symbol  will appear in the instrument cluster. The pointer is in the red range of
the gauge 1 » Fig. 5. There are now about 5 litres of fuel remaining in the tank.
If the fuel level in the fuel tank for CNG reaches the reserve level, the warning
symbol  will appear in the instrument cluster. The pointer is in the red range of
the gauge 2 » Fig. 5. There are now about 1.5 kg of fuel remaining in the tank. 
Engine revolutions counter
First read and observe the introductory information and safety warn-
ings on page 8.
The red scale of the rev counter 5 » Fig. 3 on page 8 indicates the range in which
the engine control unit begins to limit the engine speed. The engine control unit
restricts the engine speed to a steady limit.
Before reaching the red zone of the rev counter scale, shift up into the next high-
er gear.
To maintain the optimum motor speed, observe the gearshift indica-
tor » page 10.


9
Instruments and warning lights

Avoid high engine speeds during the running-in period and before the engine has
warmed up to the operating temperature .
For the sake of the environment
Shifting to a higher gear in good time helps to lower fuel consumption, minimises
operating noise levels, protects the environment and contributes to a longer life
and reliability of the engine. 
Counter for distance driven
First read and observe the introductory information and safety warn-
ings on page 8.
The distance which you have driven with your vehicle is shown in kilometres (km).
In some countries the measuring unit “mile” is used.
Reset button
To toggle between the odometer and the daily trip counter, briefly press the but-
ton 3 » Fig. 2 on page 8 or » Fig. 3 on page 8.
To reset the display of the daily trip counter, press button 3 for longer.
Daily trip counter (trip)
The daily trip counter indicates the distance which you have driven since it was
last reset - in steps of 100 metres or 1/10 of a mile.
Odometer
The odometer indicates the total distance in kilometres or miles which the vehicle
has been driven. 
Service Interval Display
First read and observe the introductory information and safety warn-
ings on page 8.
Before the next service interval, the message  appears for some seconds and
the remaining kilometres are indicated after switching on the ignition.
At the time of the service, an acoustic signal will sound and the message ap-
pears for a few seconds after switching on the ignition.


Note
■Information is retained in the Service Interval Display even after the vehicle bat-
tery is disconnected.
■If the instrument cluster is exchanged after a repair, the correct values must be
entered in the counter for the Service Interval Display. This work is carried out by
a specialist garage.
■For more information on the service intervals, see » service schedule, chap-
ter service intervals.
Recommended gear
First read and observe the introductory information and safety warn-
ings on page 8.
An information for the engaged gear is shown in the display of the instrument
cluster.
In order to minimise the fuel consumption, a recommendation for shifting into an-
other gear is indicated in the display.
Show Importance
Optimal gear.
Recommends that you shift to a higher gear.
Recommends that you shift to a lower gear.
CAUTION
The driver is always responsible for selecting the correct gear in different driving
situations, such as overtaking. 

10 Using the system

Multifunction display (onboard computer)
Introduction
This chapter contains information on the following subjects:
Memory 11
Operation 12
Digital clock 12
Multifunction display details 12
Warning against excessive speeds 13
The multifunction display can only be operated when the ignition is switched on.
After the ignition is switched on, the function displayed is the one which you last
selected before switching off the ignition.
The multi-functional indicator appears in the display » Fig. 6 on page 11.
WARNING
■Concentrate fully at all times on your driving! As the driver you are fully re-
sponsible for the operation of your vehicle.
■Do not only rely upon the information given on the outside temperature dis-
play that there is no ice on the road. Even at temperatures around +4 °C, black
ice may still be on the road surface – warning, drive with care!
Note
In certain national versions the displays appear in the Imperial system of meas-
ures. 
Memory
Fig. 6
Multifunction display
First read and observe the introductory information and safety warn-
ings on page 11.
The multifunction display is equipped with two automatic memories. The selected
memory is shown in the Display » Fig. 6.
The data of the single-trip memory (memory 1) is shown if a 1 appears in the dis-
play. A 2 shown in the display means that data relates to the total distance mem-
ory (memory 2).
Switching over the memory takes place with the button B » Fig. 7 on page 12
on the windscreen wiper lever.
Single-trip memory (memory 1)
The single-trip memory collates the driving information from the moment the ig-
nition is switched on until it is switched off. New data will also flow into the cal-
culation of the current driving information if the trip is continued within 2 hours
after switching off the ignition. If the trip is interrupted for more than 2 hours,
the memory is automatically erased.
Total-trip memory (memory 2)
The total distance driven memory gathers data from any number of individual
journeys up to a total of 19 hours and 59 minutes driving or 1 999 kilometres driv-
en. The memory is deleted when either of these limits is reached and the calcula-
tion starts all over again.
Unlike the single-trip memory, the total-trip memory is not deleted after a period
of interruption of driving of 2 hours. 

11
Instruments and warning lights

Note
All information in the memory 1 and 2 is erased if the battery of the vehicle is dis-
connected. 
Operation
Fig. 7
Multifunction display: Control el-
ements
First read and observe the introductory information and safety warn-
ings on page 11.
The rocker switch A and the button B are located on the windscreen wiper lev-
er » Fig. 7.
Select memory
›Press the button B » Fig. 7.
Selecting functions
›Briefly press the rocker switch A » Fig. 7 up or down. This opens the individual
functions of the multifunction display one after the other.
Resetting
›Select the desired memory.
›Press the button B » Fig. 7 for longer.
The following readouts of the selected memory will be set to zero by button B:
›Average fuel consumption
›Distance driven
›Average speed
›Driving time 

Digital clock
First read and observe the introductory information and safety warn-
ings on page 11.
The time is set as follows:
›Press the rocker switch A » Fig. 7 on page 12 up or down to change the display
of the time.
›Press the button 6 » Fig. 3 on page 8 to select the hour display so that it flash-
es.
›Press button 3 to continue setting the time. Keep the button pressed to run
through the numbers quickly.
›Press the button 6 to select the minutes display so that it flashes.
›Press button 3 to continue setting the time. Keep the button pressed to run
through the numbers quickly.
›Confirm the set value by pressing the button 6 again, or wait for around 5 sec-
onds. The setting is saved automatically (the value stops flashing). 
Multifunction display details
First read and observe the introductory information and safety warn-
ings on page 11.
Outside temperature
The current outside temperature is shown in the display.
If the outside temperature drops below +4 °C, the temperature indicator appears
and a snow flake symbol (black ice warning) flashes for a few seconds, then re-
mains displayed together with the outside temperature.
Driving time
The driving time which has elapsed since the memory was last erased, appears in
the display » page 11. If you want to measure the driving time from a particular
moment in time on, at this moment, reset the memory by setting the button
B » Fig. 7 on page 12 to zero.
The maximum distance indicated in both memories is 19 hours and 59 minutes.
The indicator is set back to zero if this period is exceeded. 


12 Using the system

Current fuel consumption
The current fuel consumption level is shown in the display in litres/100 km1). You
can use this information to adapt your driving style to the desired fuel consump-
tion.
The display appears in litres/hour if the vehicle is stationary or driving at a low
speed2).
Average fuel consumption
The average fuel consumption since the memory was last erased is shown in the
display in litres/100 km1 ) » page 11. You can use this information to adapt your
driving style to the desired fuel consumption.
If you wish to determine the average fuel consumption over a certain period of
time, you must set the memory at the start of the new measurement to zero us-
ing the button B » Fig. 7 on page 12. A zero appears in the display for the first
approx. 300 m you drive after erasing the memory.
The display is updated regularly while you are driving.
Range
The estimated range in kilometres is shown on the display. It indicates the dis-
tance you can still drive with your vehicle based on the level of fuel in the tank
and the same style of driving.
The display is shown in steps of 10 km. After lighting up of the warning light for
the fuel reserve the display is shown in steps of 5 km.
The fuel consumption over the last 50 km is used to calculate the range. The
range will increase if you drive in a more economical manner.
Distance travelled
The distance driven since the memory was last erased appears in the dis-
play » page 11. If you want to measure the distance travelled from a particular mo-
ment in time on, at this moment, reset the memory by setting the button
B » Fig. 7 on page 12 to zero.
The maximum distance indicated in both memories is 1 999 km. The indicator is
set back to zero if this period is exceeded.
Average speed
The average speed since the memory was last erased is shown in the display
in km/hour » page 11. If you wish to determine the average speed over a certain
period of time, you must set the memory to zero at the start of the measurement
using the button B on the windscreen wiper lever » Fig. 7 on page 12.
After erasing the memory, no value appears in the display until you have driven
approx. 300 m.
The display is updated regularly while you are driving.
Current speed
The current speed which is identical to the display of the speedometer 1 » Fig. 3
on page 8 is indicated on the display.
Coolant temperature
The current coolant temperature is shown in the display. 
Warning against excessive speeds
First read and observe the introductory information and safety warn-
ings on page 11.
Adjust the speed limit while the vehicle is stationary
›With button A » Fig. 7 on page 12, choose the menu point Warning against ex-
cessive speeds.
›Press the button B to activate the ability to set the speed limit (value flashes).
›Use the button A to set the required speed limit, e.g. 50 km/h.
›Confirm the speed limit that was set with button B, or wait approx. 5 seconds
until the setting is saved automatically (the value stops flashing).
This allows you to set the speed in 5 km/h intervals.
Adjusting the speed limit while the vehicle is moving
›With button A » Fig. 7 on page 12, choose the menu point Warning against ex-
cessive speeds.
›Drive at the desired speed, e.g. 50 km/h.
›Press button B to accept the current speed as the speed limit (the value flash-
es). 

1) On some models in certain countries, the display appears in kilometres/litre.
2) On some models in certain countries, the display appears in --,- kilometres/litres if the vehicle is sta-
tionary.
13
Instruments and warning lights

If you wish to change the set speed limit, it is changed in 5 km/h intervals (e.g. the
accepted speed of 47 km/h increases to 50 km/h or decreases to 45 km/h).
›Confirm the speed limit that was set by pressing button B again, or wait ap-
prox. 5 seconds until the setting is saved automatically (the value stops flash-
ing).
Change or delete speed limit
›With button A » Fig. 7 on page 12, choose the menu point Warning against ex-
cessive speeds.
›Pressing the button B deletes the speed limit.
›Pressing the button B activates the ability to change the speed limit.
If the set speed limit is exceeded, an audible signal will sound as a warning. At
the same time the message Warning against excessive speeds appears on the
display with the set limit value.
The set speed limit value remains stored even after switching off the ignition. 
Warning lights
Introduction
This chapter contains information on the following subjects:
 Handbrake 14
Braking system 14
 Seat belt warning light 15
 Generator 15
 Engine oil pressure 15
 Coolant temperature/coolant level 16
  Electromechanical power steering 16
 Electronic Stability Control (ESC) 16
 Traction Control System (TC) 17
Antilock brake system (ABS) 17
 Rear fog lights 17
 Exhaust inspection system 17
 EPC fault light 17
 Airbag system 18
    Automated transmission 18
  Turn signal system 18
 Cruise control system 19
 Main beam 19
/ Seat belt fastened/not fastened (belt status display) - Rear seat 19
 City Safe Drive 19
 START STOP 19
The warning lights show certain functions/faults and may be accompanied by au-
dible signals.
WARNING
■If illuminated warning lights and the corresponding descriptions and warn-
ing notes are not observed, this may result in severe injuries or major vehicle
damage.
■The engine compartment of your car is a hazardous area. There is a risk of
injuries, scalding, accidents and fire when working in the engine compart-
ment, e.g. inspecting and replenishing oil and other fluids. It is essential to ob-
serve safety notes » page 120, Engine compartment.
 Handbrake
First read and observe the introductory information and safety warn-
ings on page 14.
The warning light  comes on if the handbrake is applied. An audible warning is
also given if you drive the vehicle for at least 3 seconds at a speed of more than
6 km/h. 
Braking system
First read and observe the introductory information and safety warn-
ings on page 14.
The warning light  illuminates if the brake fluid level is too low or there is a
fault in the ABS.
Stop the vehicle, switch off the engine, and check the level of the brake flu-
id » page 127.
Further information » page 65.


14 Using the system

WARNING
■If you have to stop for technical reasons, then park the vehicle at a safe dis-
tance from the traffic, switch off the engine and activate the hazard warning
light system » page 33.
■The following guidelines should be observed when opening the bonnet and
checking the brake fluid level » page 120, Engine compartment.
■If the warning light  is displayed simultaneously with warning light
 » page 17, Antilock brake system (ABS),  do not continue your jour-
ney! Seek help from a specialist garage.
■A fault to the braking system can increase the vehicle's braking distance! 
 Seat belt warning light
First read and observe the introductory information and safety warn-
ings on page 14.
The warning light  comes on after the ignition is switched on as a reminder for
the driver and front passenger to fasten the seat belt. The warning light only
goes out if the driver or front passenger has fastened his seat belt.
If the seat belt has not been fastened by the driver or front passenger, a perma-
nent warning signal sounds at vehicle speeds greater than 25 km/h and simulta-
neously the warning light  flashes.
If the seat belt is not fastened by the driver or front passenger during the next
90 seconds, the warning signal is deactivated and the warning light  lights up
permanently.
Further information » page 91, Seat belts.
 Generator
First read and observe the introductory information and safety warn-
ings on page 14.
If the warning light lights up  when the engine is running, the vehicle battery is
not being charged.
Seek help from a specialist garage. The electrical system requires checking.


WARNING
If you have to stop for technical reasons, then park the vehicle at a safe dis-
tance from the traffic, switch off the engine and activate the hazard warning
light system » page 33.
CAUTION
If the warning light  (cooling system fault) comes on in addition to the warning
light  in the display when driving, stop the vehicle immediately and switch the
engine off – risk of engine damage! 
 Engine oil pressure
First read and observe the introductory information and safety warn-
ings on page 14.
The warning light  comes on for a few seconds when the ignition is switched
on.
Stop the vehicle and switch the engine off if the warning light does not go off
after the engine has started or flashes while driving. Check the oil level and top
up with engine oil if necessary » page 124, Checking the oil level.
An audible signal sounds as a warning signal.
Do not continue your journey if for some reason it is not possible to top up the
engine oil under the prevailing conditions. This can cause serious engine damage.
Therefore, switch the engine off and seek help from a specialist garage.
Even if the oil level is correct,  do not drive any further if the warning light is
flashing. Also do not leave the engine running at an idling speed.
Seek help from a specialist garage.
WARNING
If you have to stop for technical reasons, then park the vehicle at a safe dis-
tance from the traffic, switch off the engine and activate the hazard warning
light system » page 33, Hazard warning light system.

15
Instruments and warning lights

CAUTION
The red oil pressure light  is not an oil level indicator! One should therefore
check the oil level at regular intervals, preferably after every refuelling stop. 
 Coolant temperature/coolant level
First read and observe the introductory information and safety warn-
ings on page 14.
The warning light  comes on for a few seconds when the ignition is switched
on.
If the warning light  lights up or flashes, either the coolant temperature is too
high or the coolant level is too low.
An audible signal sounds as a warning tone.
Stop the vehicle, switch off the engine, check the level of the coolant » page 126,
and refill the coolant if necessary » page 126.
Do not continue your journey if for some reason it is not possible to top up the
coolant under the prevailing conditions. This can cause serious engine damage.
Therefore, switch the engine off and seek help from a specialist garage.
If the coolant is within the specified range, the increased temperature may be
caused by an operating problem at the radiator fan. Check the fuse for the radia-
tor fan, replace if necessary » page 150, Fuses in the engine compartment.
Do not continue driving if the warning light   does not go off even though the
coolant level is correct and the fuse for the fan is in working order!
Seek help from a specialist garage.
WARNING
If you have to stop for technical reasons, park the vehicle at a safe distance
from traffic, switch off the engine and switch on the hazard warning light sys-
tem » page 33.

  Electromechanical power steering
First read and observe the introductory information and safety warn-
ings on page 14.
The warning light  comes on for a few seconds when the ignition is switched
on.
If the warning light after switching on the ignition or when driving lights up con-
tinuously, a fault exists in the electromechanical power steering.
›If the yellow warning light lights up , this indicates a partial failure of the
power steering and the steering forces can be greater.
›If the red warning light lights up , this indicates a complete failure of the pow-
er steering and the steering assist has failed (significantly higher steering
forces).
Further information » page 64.
Note
■If the yellow warning light  goes out after starting the engine again and driv-
ing a short distance, it is not necessary to visit a specialist garage.
■If the vehicle battery has been disconnected and reconnected, the yellow warn-
ing light  comes on after switching on the ignition. The warning light should go
out after driving a short distance. 
 Electronic Stability Control (ESC)
First read and observe the introductory information and safety warn-
ings on page 14.
The warning light flashes to show that the ESC is currently operating.
If the warning light  lights up, there is a fault in the ESC.
As the ESC operates in conjunction with the ABS, the ESP warning light will also
come on if the ABS system fails.
If the warning light  comes on immediately after starting the engine, the ESC
can be switched off for technical reasons. In this case, the ESC can be switched
on again by switching the ignition on and off. If the warning light goes out, the
ESC is fully functional again.
Further information » page 77, Electronic Stability Control (ESC).


16 Using the system

Note
If the vehicle's battery has been disconnected and reconnected, the warning light
 comes on after switching on the ignition. The warning light should go out after
driving a short distance. 
 Traction Control System (TC)
First read and observe the introductory information and safety warn-
ings on page 14.
The warning light  comes on for a few seconds when the ignition is switched
on.
The warning light comes on when driving when a control cycle is activated.
The warning light illuminates permanently if there is a fault in the TCS.
The fact that the TCS operates together with the ABS means that the TCS warn-
ing light will also come on if the ABS system is not operating properly.
If the warning light  comes on immediately after starting the engine, the TCS
can be switched off for technical reasons. In this case, the TCS can be switched
on again by switching the ignition on and off. If the warning light goes out, the
TCS is fully functional again.
Further information » page 78, Traction Control System (TCS).
Note
If the vehicle's battery has been disconnected and reconnected, the warning light
 comes on after switching on the ignition. The warning light should go out after
driving a short distance. 
Antilock brake system (ABS)
First read and observe the introductory information and safety warn-
ings on page 14.
If the warning light  lights up, there is a fault in the ABS.
The vehicle will only be braked by the normal brake system without the ABS.
Seek help from a specialist garage.


Further information » page 78, Antilock Braking System (ABS).
WARNING
■If you have to stop for technical reasons, then park the vehicle at a safe dis-
tance from the traffic, switch off the engine and activate the hazard warning
light system » page 33.
■If the warning light  » page 14 is displayed simultaneously with the ABS
warning light ,  do not continue your journey! Seek help from a specialist
garage.
■The following guidelines should be observed when opening the bonnet and
checking the brake fluid level » page 120, Engine compartment.
 Rear fog lights
First read and observe the introductory information and safety warn-
ings on page 14.
The warning light  comes on when the rear fog lights are operating » page 33.
 Exhaust inspection system
First read and observe the introductory information and safety warn-
ings on page 14.
If the warning light  lights up, there is a fault in the exhaust inspection system.
The engine control unit allows the vehicle to run in emergency mode.
Seek help from a specialist garage. 
 EPC fault light
First read and observe the introductory information and safety warn-
ings on page 14.
If the warning light  lights up, there is a fault in the engine control. The engine
control unit allows the vehicle to run in emergency mode.
Seek help from a specialist garage. 



17
Instruments and warning lights

 Airbag system
First read and observe the introductory information and safety warn-
ings on page 14.
Monitoring the airbag system
The warning light  comes on for a few seconds when the ignition is switched
on.
There is a fault in the system if the warning light does not go out or flashes while
driving » . This also applies if the warning light does not come on when the ig-
nition is switched on.
The functionality of the airbag system is also monitored electronically when one
airbag has been switched off.
The following situation applies if the front or side airbag or belt tensioner have
been switched off using the vehicle system tester:
›The warning light  lights up for around 4 seconds after switching on the igni-
tion and then flashes approximately another 12 seconds in 2 second intervals.
The following situation applies if the airbag has been switched off using the
key switch for the airbag in the front passenger storage compartment:
›The warning light  comes on for a few seconds when the ignition is switched
on;
›The deactivated airbag is indicated by the illumination of the warning light
     in the middle of the dash panel » page 99, Deactivating
the front passenger airbag.
WARNING
If there is a fault, have the airbag system checked immediately by a specialist
garage. Otherwise, there is a risk that the airbag will not be deployed in the
event of an accident. 
    Automated transmission
First read and observe the introductory information and safety warn-
ings on page 14.
Warning light 
Do not continue your journey if the warning light  lights up and an acoustic sig-
nal sounds. Switch off the engine and seek assistance from a specialist garage.


Warning light 
If the warning light  lights up and no gear can be selected, switch the ignition
on and off. If the warning light lights up after you switch on the ignition, seek as-
sistance from a specialist garage.
If the warning light  or warning light  lights up and an acoustic signal sounds,
this means that the automatic gearbox has overheated. Stop and allow the trans-
mission to cool down or drive more quickly than 20 km/h (12 mph).
If the warning light  lights up again, switch off the vehicle, shut off the engine
and allow the gearbox to cool down.
Warning light 
If the warning light  lights up, operate the brake pedal.
Warning light 
If the warning light  lights up, operate the handbrake.
Further information » page 67, Automatic gearbox.
WARNING
If you have to stop for technical reasons, park the vehicle at a safe distance
from traffic, switch off the engine and switch on the hazard warning light sys-
tem » page 33.
  Turn signal system
First read and observe the introductory information and safety warn-
ings on page 14.
Either the left  or right  warning light flashes depending on the position of the
turn signal lever.
If a turn signal light fails, the warning light flashes at twice its normal rate.
Switching off the hazard warning light system is switched on will cause all of the
turn signal lights as well as both warning lights to flash.
Further information » page 32, Turn signal and main beam light.

18 Using the system